NEC P401w Projector User Manual

119
5. Using On-Screen Menu
NETWORK PROJECTOR
This	shows	 information 	for	 projector 	name,	 resolution, 	and	 network 	(wired/wireless) 	which 	are	 required 	to	 use	 Network	
Projector.
Use	this	information	to	set	up	for	your	computer.
REMOTE DESKTOP CONNECTION
This	allows	you	to	set	up	for	computer	name	entry	and	effects	for	Remote	Desktop.
NOTE:
•	 A	USB	keyboard	is	required	to	set	up	the	Remote	Desktop	Connection. 

120
5. Using On-Screen Menu
NETWORK SETTINGS
Important:
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wired	 LAN	connection,	 connect	a	LAN	 cable	 (Ethernet	 cable)	to	the	 LAN	 port	(RJ-45)	 of	the	 projector.	 (→	page	
151)	
TIP:	The	network	settings	you	make	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Hints	on	How	to	Set	Up	LAN	Connection	
To	set	up	the	projector	for	a	LAN	connection:
Select	[WIRED	LAN]	or	[WIRELESS	LAN]	→	[PROFILES]	→	[PROFILE	1]...

121
5. Using On-Screen Menu
WIRED	LAN	or	WIRELESS	LAN	(ADVANCED	menu	only)
PROFILES•	 Up	to	two	 settings	 for	the	 LAN	 port	or	USB	 wireless	 LAN	unit	
can	be	stored	 in	memory	 of	the	 projector. 	Total	 of	four	 settings	
can be stored.
	 Five	 settings	 can	be	stored: 	two	 for	the	 built-in	 LAN	port,	 two	
for	wireless	LAN	and	one	for	 WPS.
•	 Select	[PROFILE	 1]	or	 [PROFILE	 2]	and	 then	 do	settings	 for	
[DHCP]	and	the	other	options. 	
	 After	doing	this,	select	 [OK]	and	press	 the	ENTER...

122
5. Using On-Screen Menu
•	 When	selecting	 [WPS],	the	network	 will	be	connected	 by	using	
settings	stored	automatically	with	the	 WPS	function.
	 Selecting	[WPS]	will	allow	 the	projector	 to	access	 the	network	
by	using	the	settings	the	 WPS	function	automatically	stored.
DHCPPlace	a	check	 mark	to	automatically	 assign	an	IP	address	 to	the	
projector	from	your	DHCP	server.
Clear	 this	check	 box	to	register	 the	IP	address	 or	subnet	 mask	
number	obtained	from	your	network	administrator.
—
IP...

123
5. Using On-Screen Menu
SITE	SURVEYDisplays	a	list	 of	available	 SSIDs	for	wireless	 LAN	on	site. 	Select	
an	SSID	which	you	can	access.
To	 select	 an	SSID,	 highlight	 [SSID]	and	use	the	SELECT	→  to 
select	[OK]	and	press	the	ENTER	button. 	
 �����������������������Wireless access point 
 �����������������������Ad Hoc PC 
 �����������������������WEP or WPA enabled —
SECURITY
This	 will	turn	 on	or	off	 the	 encryption	 mode	for	secure	 transmis-
sion.
To	 use	 encryption,	 specify	a	WEP	 key	or...

124
5. Using On-Screen Menu
When	[WEP(64bit)]	or	[WEP(128bit)]	is	selected	for	[SECURITY	TYPE]
KEY	SELECTSelects	one	WEP	key	from	the	four	keys	below.
KEY1,	KEY2,	KEY3,	
KEY4
Enter	a	WEP	key.
•	Maximum	number	of	characters
Option Alphanumeric	(ASCII) Hexadecimal	(HEX)
WEP	64bit 510
WEP 128bit 1326
When	[WPA-PSK],	[WPA-EAP],	[WPA2-PSK], 	or	[WPA2-EAP]	is	selected	for	[SECURITY	 TYPE]
ENCRYPTION	TYPESelect	[TKIP]	or	[AES].
KEYEnter	encryption	key. 	Key	length	must	be	8	or	greater	and	63	or	less. 

125
5. Using On-Screen Menu
[AUTHENTICATION]	(required	for	wireless	only)
Setting	is	required	for	using	WPA-EAP	or	WPA2-EAP.	
Preparation	before	setting
Select	a	wireless	 LAN	compliant	 WPA-EAP	 or	WPA2-EAP	 authentication	 and	install	 a	digital	 certificate	 on	the	 projec-
tor.
1.	 Set	[DATE	AND	 TIME]	on	the	projector. 	(→	page	140)
2.	 Use	a	computer	 to	save	 digital	 certificates	 (files)	for	WPA-EAP	 or	WPA2-EAP	 setting	to	your	 USB	memory	
device.
 After completing saving the file, remove the...

126
5. Using On-Screen Menu
4.	 Select	[SITE	SURVEY]	and	press	the	ENTER	button.
	 The	“SSID”	list	will	be	displayed.
5.	 Select	a	connecting	SSID, 	and	then	select	[OK].
 Finally press the ENTER button.
•	 Select	the	SSID	for	which	 WPA-PSK	or	WPA2-PSK	is	set.
•	 Select	[INFRASTRUCTURE	 ()] for [NETWORK TYPE]. WPA-PSK, WPA2-PSK, WPA-EAP, or WPA2-EAP is 
not available when [AD HOC ()] is selected.
6.	 Select	the	[SECURITY]	tab.
	 The	[SECURITY]	page	will	be	displayed.
7.	 Select	the	[SECURITY	 TYPE]...

127
5. Using On-Screen Menu
11.	Select	the	[AUTHENTICATION]	tab.
	 The	[AUTHENTICATION]	page	will	be	displayed.
 Select  either  [EAP-TLS]  or  [PEAP-MSCHAPv2]  for  [EAP TYPE]. The  setting  items  vary  depending  on  the  EAP 
type.
 See the table below.
EAP	 TypeSetting	ItemNote
EAP-TLS
User	Name1  character  or  more  and  32  characters  or 
less
Client	CertificatePKCS#12	format	file
CA	Certificate
(Certificate	authority’s	certificate)
DER	format	file
PEAP-MSCHAPv2User	Name1  character  or  more...

128
5. Using On-Screen Menu
13.	Select	[CLIENT	CERTIFICATE]	and	press	the	ENTER	button.
A	list	of	files	([FILES]	screen)	will	be	displayed.
•	 For	operating	the	[FILES]	screen,	see	“4.	Using	the	 Viewer”	in	the	“User’s	Manual” 	(PDF).
•	 To	return	to	the	[AUTHENTICATION]	page,	press	the	EXIT	button.
NOTE:
Installing	a	digital	certificate
You	can	install	each	digital	certificate	(client	certificate	and	CA	certificate)	for	[PROFILE	1	(or	2)]	on	a	file-by-file	basis.
•	 Install	a	root	CA	certificate	for	a...