NEC Np64 Projector User Manual

12
2. Installation and Connections
COMPUTER IN
PHONE
PHONE
AUDIO IN
➋ Making Connections
Connecting Your PC or Macintosh Computer
NOTE:	When	using	with	a	notebook	 PC,	be	sure	 to	connect	 the	projector	 and	notebook	 PC	while	 the	projector	 is	in	 standby	 mode	and	
before	turning	on	the	power	to	the	notebook	PC.
In	most	cases	the	output	signal	from	the	notebook	PC	is	not	turned	on	unless	connected	to	the	projector	before	being	powered	up.
*	 If	the	screen	 goes	blank	 while	using	 your	remote...

13
2. Installation and Connections
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
COMPUTER IN AUDIO IN
NOTE:	Refer	to	your	DVD	player’s	owner’s	manual	for	more	information	about	your	DVD	player’s	video	output	requirements.
Connecting Your DVD Player with Component Output
Use	audio	equipment	for	stereo	sound.
The	projector’s	built-in	speaker	is	monaural.
DVD player
Audio Equipment
Optional 15-pin - to - RCA (female) 
× 3 cable (ADP-CV1E)
Component video RCA × 3 cable (not supplied)
Audio cable (not supplied)...

14
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO
VIDEO
VIDEO IN
S-VIDEO IN
AUDIO IN
Connecting Your VCR
Use	audio	equipment	for	stereo	sound.
The	projector’s	built-in	speaker	is	monaural.
S-Video cable (not supplied)
Video cable (not supplied)
VCR
Audio equipment
Audio cable (not supplied)
NOTE:	Refer	to	your	VCR	owner’s	manual	for	more	information	about	your	equipment’s	video	output	requirements.
NOTE:	An	image	 may	not	be	displayed	 correctly	when	a	Video	 or	S-Video	 source	is...

15
2. Installation and Connections
Connecting the Supplied Power Cable
Connect	the	supplied	power	cable	to	the	projector.
First	connect	 the	supplied	 power	cable’s	 three-pin	 plug	to	the	 AC	IN	of	the	 projector,	 and	then	 connect	 the	other	
plug	of	the	supplied	power	cable	in	the	wall	outlet.
To wall outlet
The	 projector	 will	go	into	 standby	
mode.	 When	in	standby	 mode,	the	
POWER	 indicator	 will	light	 orange	
and	the	STATUS	 indicator	 will	light	
green	when	[NORMAL]	is	selected	
for...

16
AUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
3. Projecting an Image (Basic Operation)
This	section	describes	how	to	turn	on	the	projector	and	to	project	a	picture	onto	the	screen.
➊
 Turning on the Projector
NOTE:	 Before	 turning	 on	the	 projector,	 first	connect	 the	supplied	 power	cable’s	 three-pin	 plug	to	the	 AC	IN	of	the	 projector,	 and	
then	connect	 the	other	 plug	of	the	 supplied	 power	cable	in	the	 wall	 outlet.	 Make	sure	that	the	projector	 is	in	 its	 standby	 mode	
and	the	power...

17
3. Projecting an Image (Basic Operation)
SOURCEAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
SOURCEAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
Note on Startup screen (Menu Language Select screen)
When	
you	first	 turn	 on	the	 projector,	 you	will	get	the	 Startup	 menu.	The	menu	 gives	you	the	opportunity	 to	select	
the	menu	in	one	of	the	21	languages.
To select a menu language, follow these steps:
1.  Use  the ▲
, 
▼
, 
◀  or  ▶  button  to  select  one  of  the  21 
languages from the menu.
2....

18
3. Projecting an Image (Basic Operation)
SOURCEAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
➋ Selecting a Source
Selecting the computer or video source
NOTE:	Turn	on	the	computer	or	video	source	equipment	connected	to	the	projector.
Adjusting with buttons on the cabinet
1. 
Press the ▶ (SOURCE) button with no menus displayed.
 The Source list will be displayed.
 - When the menu is displayed, press the EXIT button to close the menu 
and start the operation.
2. Press the ▶ button a few times quickly to...

19
3. Projecting an Image (Basic Operation)
Selecting Default Source
You	can	set	a	source	 as	the	 default	 source	 so	that	 the	default	 source	 will	be	displayed	 each	time	the	projector	 is	
turned	on.
1. Press the MENU button.
 The menu will be displayed.
2. Press  the ▶  button  twice  to  select  [SETUP]  and  press 
the  ▼ button or the ENTER button to select [GENERAL].
3.  Press the ▶ button three times to select [OPTIONS(2)].
4.  P r e s s  t h e ▼  b u t t o n  s i x  t i m e s  t o  s e l e c...

20
3. Projecting an Image (Basic Operation)
Manual Operation
Place	your	projector	 on	a	flat	 level	 surface	 and	ensure	 that	the	
projector	is	square	to	the	screen.
[Adjust	the	Tilt	Foot]
Lift	the	 front	 edge	 of	the	 projector	 to	center	 the	image	 verti-
cally.	(→	page	21)
[Zoom]
Use	the	ZOOM	lever	to	adjust	the	image	size	on	the	screen.	(→	
page 	22)
➌
 Adjusting the Picture Size and Position
Automatic Operation
[AUTO FOCUS]
Just	 placing	 the	projector	 on	a	flat	 level	 surface	 makes	a	fo-...

21
3. Projecting an Image (Basic Operation)
2
1
2
1
Adjust the Tilt Foot
1. Lift the front edge of the projector.
CAUTION:
Do	 not	 try	to	touch	 the	ventilation	 outlet	during	 Tilt	Foot	 adjust-
ment	 as	it	can	 become	 heated	while	the	projector	 is	turned	 on	and	
during	its	cool	down	period	after	it	is	turned	off.
2. Push up and hold the Adjustable Tilt Foot Button on the front 
of  the  projector  to  extend  the  adjustable  tilt  foot  (maximum 
height).
3. Release the Adjustable Tilt Foot Button...