NEC Np600 Edu Projector User Manual


2. Installation and Connections
WARNING
* Installing your projector on the ceiling must be done 
by a qualified technician. Contact your NEC dealer for 
more information.
*  Do not attempt to install the projector yourself.
•  Only use your projector on a solid, level surface. If the 
projector falls to the ground, you can be injured and 
the projector severely damaged.
•  Do  not  use  the  projector  where  temperatures  vary 
greatly. The  projector  must  be  used  at  temperatures...


2. Installation and Connections
 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode 
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power manage
-
ment...

4
2. Installation and Connections
• Select the source name for its appropriate input connector after turning on the projector.
Input connectorSOURCE button on the projector 
cabinetButton on the remote control
COMPUTER 1 IN COMPUTER1(COMPUTER 1)
COMPUTER 2(DVI-I)IN
 COMPUTER 2(DIGITAL)
or
 COMPUTER 2(ANALOG)
(COMPUTER 2)
	 ↓ (Toggle)
(COMPUTER 2)
NOTE: The projector is not compatible with video decoded outputs of the \
NEC ISS-6020 switcher.
NOTE: An image may not be displayed correctly when a...

15
2. Installation and Connections
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before 
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source menu before 
turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should 
this happen, restart your PC.
Do not disconnect the DVI...

6
2. Installation and Connections
COMPUTER 1 IN COMPUTER 2 (DVI-I) IN
VGA signal cable  (supplied)
IBM PC or Compatibles (Notebook type) or Macintosh (Notebook type)
IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)
VGA signal cable (not supplied)
DVI to VGA adapter (supplied)
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do so 
may cause damage to the connector of the projector.
Using Two Analog COMPUTER...

7
2. Installation and Connections
Connecting an External Monitor
You  can  connect  a  separate,  external  monitor  to  your  projector  to  simultaneously  view  on  a  monitor  the  computer 
analog image you’re projecting.
NOTE:
• Daisy chain connection is not possible.
•  When audio equipment is connected, the projector speaker is disabled.
AUDIO IN PHONE 
MONITOR OUT (COMP 1)
AUDIO OUT 
VGA signal cable (sup-plied)
VGA signal cable (not supplied) 

8
2. Installation and Connections
Connecting Your DVD Player with Component Output
 A  component  signal  will  be  automatically  displayed.  If  not,  from  the  menu,  select  [SETUP] →  [OPTIONS(1)] → 
[SIGNAL SELECT] → [COMPUTER1], and then place a check mark in the Component radio button.
•  Select the source name for its appropriate input connector after turning on the projector.
Input connectorSOURCE button on the projector 
cabinetButton on the remote control
COMPUTER 1 IN...

9
2. Installation and Connections2. Installation and Connections
Connecting Your VCR
• Select the source name for its appropriate input connector after turning on the projector.
Input connectorSOURCE button on the projector 
cabinetButton on the remote control
VIDEO IN VIDEO(VIDEO)
S-VIDEO IN S-VIDEO(S-VIDEO)
NOTE: The AUDIO IN L and R jacks (RCA) are shared between the Video an\
d S-Video inputs.
NOTE: Refer to your VCR owner’s manual for more information about your equipment’s video output...

0
2. Installation and Connections
Connectng to a Network
The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. 
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings for the projector over a LAN. 
To use a LAN connection, you are required to assign an IP address to the projector on the [PROJECTOR NETWORK 
SETTINGS] screen of the web browser on your computer. For setting, see page 41,42,43.
Example of LAN...


2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable’s two-pin plug to the AC IN of the projector, and then connect the other plug 
of the supplied power cable in the wall outlet.
CAUTION:
Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while 
the projector is turned on and immediately after the projector is turned off.
SELECT...