NEC Np510ws Projector User Manual

22
2. Installation and Connections
Connecting Your DVD Player with Component Output
	 A	component	 signal	will	be	automatically	 displayed.	If	 not,	 from	 the	menu,	 select	[SETUP]	→	[OPTIONS(1)]	→ 
[SIGNAL	SELECT]	→	[COMPUTER1],	and	then	place	a	check	mark	in	the	Component	radio	button.
•	 Select	the	source	name	for	its	appropriate	input	connector	after	turning	on	the	projector.
[NP610/NP510/NP410/NP310/NP510W/NP410W/NP610S/NP510WS]
Input	connectorSOURCE	button	on	the	projector	
cabinetButton	on	the...

23
2. Installation and Connections2. Installation and Connections
Connecting Your VCR
•	 Select	the	source	name	for	its	appropriate	input	connector	after	turning	on	the	projector.
Input	connectorSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
VIDEO	IN	VIDEO(VIDEO)
S-VIDEO	IN	S-VIDEO(S-VIDEO)
NOTE:	The	AUDIO	IN	L	and	R	jacks	(RCA)	are	shared	between	the	Video	and	S-Video	inputs.
NOTE:	Refer	to	your	VCR	owner’s	manual	for	more	information	about	your	equipment’s	video	output...

24
2. Installation and Connections
Connecting to a Network (except NP405 and NP305)
The	projector	comes	standard	with	a	LAN	port	(RJ-45)	which	provides	a	LAN	connection	using	a	LAN	cable.	
Using	a	LAN	 cable	 allows	 you	to	specify	 the	Network	 Settings	and	the	Alert	 Mail	Settings	 for	the	 projector	 over	a	LAN. 	
To	use	 a	LAN	 connection,	 you	are	required	 to	assign	 an	IP	address	 to	the	 projector	 on	the	 [PROJECTOR	 NETWORK	
SETTINGS]	screen	of	the	web	browser	on	your	computer. 	For	setting,...

25
2. Installation and Connections
Connecting the Supplied Power Cable
Connect	the	supplied	power	cable	to	the	projector.
First	connect	 the	supplied	 power	cable’s	 two-pin	 plug	to	the	 AC	IN	of	the	 projector,	 and	then	 connect	 the	other	 plug	
of	the	supplied	power	cable	in	the	wall	outlet.
CAUTION:
Do	not	 try	to	touch	 the	ventilation	 outlet	on	the	 left	front	 (when	 seen	from	the	front)	 as	it	can	 become	 heated	while	
the projector is turned on and immediately after the projector is turned...

26
3. Projecting an Image (Basic Operation)
This	section	describes	how	to	turn	on	the	projector	and	to	project	a	picture	onto	the	screen.
1 Turning on the Projector
NOTE:
•	 The	projector	 has	two	 power	 switches:	 a	main	 power	 switch	 and	a		(POWER)	 button	(POWER	 ON	and	 OFF	 on	the	 remote	
control).
•	 When	 plugging	 in	or	 unplugging	 the	supplied	 power	cable,	make	sure	that	the	main	 power	 switch	 is	pushed	 to	the	 off	() posi-
tion.	Failure	to	do	so	may	cause	damage	to	the	projector.
1....

27
3. Projecting an Image (Basic Operation)
3. Press the  (POWER) button on the projector cabinet 
or the POWER ON button on the remote control for 1 
second. 
  The POWER indicator will turn to green and the projector 
will become ready to use.
NOTE: When the projector is turned on, it may take some time 
before the lamp light becomes bright.
TIP: 
•	 When	 the	STATUS	 indicator	 lights	orange,	 it	means	 that	the	
[CONTROL	PANEL	LOCK]	is	turned	on.	(→ page 72)
•	 When 	the 	message	 “Projector 	is...

28
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When	you	first	 turn	 on	the	 projector,	 you	will	get	 the	Startup	 menu.	This	 menu	 gives	you	the	opportunity	 to	select	 one	
of the 21 menu languages.
To	select	a	menu	language, 	follow	these	steps:
1. Use  the , ,   or   button  to  select  one  of  the  21 
languages from the menu.
2.  Press the ENTER button to execute the selection.
After  this  has  been  done,  you  can  proceed  to  the  menu...

29
3. Projecting an Image (Basic Operation)
VOLUMEL-CLICK
MOUSER-CLICK
AUTO ADJ.
ASPECT HELP
FREEZE
PICTURE
S-VIDEO VIDEOCOMPUTER
2ECO MODE1
MENU 
EXIT ENTER 
ST
ATUS 
LAMP 
AUTO ADJ. 
SOURCE 
 Selecting a Source
Selecting the computer or video source
NOTE:	Turn	on	the	computer	or	video	source	equipment	connected	to	the	projector.
Selecting	from	Source	List
Press	 and	quickly	 release	 the	SOURCE	 button	on	the	 projector	 cabinet	to	
display	 the	Source	 list.	Each	 time	the	SOURCE	 button	is	pressed,...

30
3. Projecting an Image (Basic Operation)
 Adjusting the Picture Size and Position
Use	the	adjustable	tilt	foot,	the	zoom	function	or	the	focus	ring	to	adjust	the	picture	size	and	position.
In this chapter drawings and cables are omitted for clarity.
Adjusting	the	throw	angle	(the	height	of	an	image)
[Tilt	foot]	(→ page 31)
Adjusting the left and right tilt of an image
[Rear	foot]	(→ page 31)
Finely	adjusting	the	size	of	an	image
[Zoom	function]	(→ page 32)
Adjusting the focus
[Focus	ring]	(→ page...

31
3. Projecting an Image (Basic Operation)
2 
1 
3 4 
Adjustable Tilt FootAdjustable Tilt 
Foot Lever
Adjust the Tilt Foot
1.  Lift the front edge of the projector.
CAUTION:
Do	 not	 try	to	touch	 the	ventilation	 outlet	during	 Tilt	Foot	 adjustment	
as	it	can	 become	 heated	while	the	projector	 is	turned	 on	and	 after	 it	
is turned off.
2.  Push up and hold the Adjustable Tilt Foot Lever on the front of 
the projector to extend the adjustable tilt foot.
3.  Lower the front of the projector to the...