NEC Np200 Portable Projector Users Manual

5... English
Introduction
Power Cable
US (P/N:79TC1031)
EU (P/N: 79TC1041)
CH (P/N: 79TC1051) VGA Cable
(P/N : 79TC1001)
Wireless Remote Control
(P/N:79TC1021)
Projector with lens cap
(P/N:79TC1011)
Package Overview
This projector comes with all the items shown below. Check to 
make sure your unit is complete. Contact your dealer immedi -
ately if anything is missing.
	 Due to the differ-
ence in applications 
for each country, some 
regions may have dif-
ferent accessories.
Documentation: 
	CD-ROM...

6
English ...
Introduction
1.  Power 
2.  Remote Control
3.  Power (LED indicator)
4.  Zoom and Focus Rings
5.   Speaker
6.   Lens
7.  Lens Cap
8.  Ventilation (inlet)
9.  Ventilation (outlet)
10.  Remote Sensor
Projector
Product Overview
1
2
3
4
5
6
7
8
8
9
	 To release the 
remote control from the 
projector gently press 
down on the top of the 
remote control above 
the “Picture” button.  
This will cause the 
bottom of the remote 
control to pop-up for 
removal from the cabi-
net.  Be careful not to...

7... English
Introduction
Connection Ports
1. COMPUTER IN Connector
2.  S-VIDEO IN Connector
3.  VIDEO IN Connector
4.  SERVICE Port
5.  MONITOR OUT Connector
6.  AUDIO IN Jack
7.  AC IN
8.  Kensington
TM Lock Port
1 23 4 56
7 8 

8
English ...
Introduction
Wireless Remote Control
1Power Refer to the “Power On/Off 
the Projector” section on pages 
12-13.
2 Picture Mode Select the Picture mode from 
Presentation, Movie, sRGB, 
Game and User.
3 Computer 
Source Press “Computer” to choose 
Computer connector.
4 Freeze Freeze To pause the screen im-
age. Press again to resume the 
screen image.
1
2
3 10
4
6
7
8 9
11
5 12
13
14
16
17
15
5
	 Before using the 
remote control for the 
first time, remove the 
transparent insulation 
tape....

9... English
Introduction
5 Keystone  
Correction Adjust the image to compensate 
for distortion caused by tilt-
ing the projector (vertical ± 40 
degrees).
6 Source Press “Source” to choose RGB, 
Component, S-Video, Composite 
and HDTV sources.
7 Menu Press “Menu” to launch the 
Onscreen display (OSD), back to 
the top level of OSD for the OSD 
main menu operation
8 AV-Mute Momentarily turn off/on the 
audio and video.
9 Reset Change the adjustments and set-
tings to the factory default value.
10 Video...

10
English ...
Introduction
Battery Installation
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Do not place the battery upside down.
1. Press firmly and slide the battery cover off.
MnO2-LiCELL3VOLTSJAPANHC R202 5
2.  Remove the old Lithium 
coin cell and install new one 
(CR2025). Ensure that the 
side with a “+” is facing up.
3VOLTSCR202 5
3.  Put the cover back.
M3VOLTSCR2025
	 Keep...

11... English
Installation
Connecting the Projector
	Due to the differ-
ence in applications 
for each country, some 
regions may have differ-
ent accessories.
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your projector.
1. ........................................................................\
................... Power cable (supplied)
2. ........................................................................\...

12
English ...
Installation
Powering On the Projector
1.  Ensure that the power cable and signal cable are securely 
connected. The Power LED will flash blue.
2.    Remove the lens cap. 
3.    Turn on the lamp by pressing “Power” on the control panel. 
 The startup screen (NEC logo) will display and the Power 
LED will turn blue.
4.    Turn on your source (computer, notebook, video player,etc.) 
The projector will detect your source automatically.
		 If you connect multiple sources at the same time,...

13... English
Installation
Powering Off the Projector
1.    Press the “Power” to turn off the projector lamp, you will 
see a message as below on the on-screen display.
 
2.    Press the “Power” again to confirm. 
3.    The cooling fan continues to operate for about 120 seconds 
during the cool down period and the Power LED will flash 
blue. When the light starts flashing, the projector has entered 
standby mode.
    If you wish to turn the projector back on, you must wait 
until the projector has...

14
English ...
Installation
Warning Indicator
    When the “Power” LED indicator turns red, it indicates the 
projector has overheated. The projector will auto matically 
shut itself down.
    When the “Power” LED indicator flashes red and the mes -
sage below displays on-screen, the projector has detected 
that the lamp is approaching its end of life. When you see 
this message, change the lamp as soon as possible or contact 
your local dealer or our service center. 
    When the “Power” LED...