NEC Neax 2000 Ivs2 Office Data Programming Manual

 NEAX2000 IVS2 Office Data Programming ManualPage ii  ND-70931 (E), Issue 2.0
TABLE OF CONTENTS
Page
CM38  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . . .  314
CM40  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . . .  315
CM41  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

TABLE OF CONTENTS
Page
NEAX2000 IVS2 Office Data Programming Manual    
ND-70931 (E), Issue 2.0   Page iii
CMAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . . .  411
CMAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . . .  416
CMAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

 NEAX2000 IVS2 Office Data Programming ManualPage iv  ND-70931 (E), Issue 2.0
LIST OF TABLES
Table TitlePage
Table 1-1 Numbering Plan Data Table  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
Table 1-2 Station Data Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
Table 1-3 Trunk Data Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

INTRODUCTION
Purpose
NEAX2000 IVS2 Office Data Programming Manual   ND-70931 (E), Issue 2.0  Page 1
INTRODUCTION
PURPOSE
This manual is used for programming office data and for designing the system layout required
for customizing the NEAX2000 IVS
2.
Before starting installation work, the installer must fill in the office data sheet and draw the system
layout and floor layout in this manual according to customer’s requirements. In the course of this
work, the installer should use the Office Data...

 NEAX2000 IVS2 Office Data Programming ManualPage 2  ND-70931 (E), Issue 2.0
INTRODUCTION
Reference Manual
REFERENCE MANUAL
For additional information on office data programming, refer to the following manuals:
Installation Procedure Manual Describes the installation procedure of the PBX system.
Command Manual Describes Customer Administration Terminal (CAT)
operation, command function and setting data required for
programming the system, and Resident System Program. 

INTRODUCTION
Data Programming Procedure
NEAX2000 IVS2 Office Data Programming Manual   ND-70931 (E), Issue 2.0  Page 3
DATA PROGRAMMING PROCEDURE
The following table shows the procedure and the outline of the office data programming for the
system.
The office data specified in this manual are entered to the system through the Customer
Administration Terminal (CAT) or Maintenance Administration Terminal (MAT).
STEP WORK REMARKS
1. Obtain the customer’s requirements, and 
fill in the customer...

 NEAX2000 IVS2 Office Data Programming ManualPage 4  ND-70931 (E), Issue 2.0
This page is for your notes. 

NEAX2000 IVS2 Office Data Programming Manual    
ND-70931 (E), Issue 2.0   Page 5
CHAPTER 1 
CUSTOMIZING OFFICE 
DATA
This chapter explains how to customize the office data, and contains
the customer specifications sheets which include the numbering plan,
station data and trunk data, port assignment table, etc. 

 NEAX2000 IVS2 Office Data Programming ManualPage 6  ND-70931 (E), Issue 2.0
CHAPTER 1  CUSTOMIZING OFFICE DATA
How to Customize Office Data
HOW TO CUSTOMIZE OFFICE DATA
This section explains how to customize the office data.
The “Customer Specifications Sheet” section provides the data tables for the following items:
Numbering Plan
The Numbering Plan Data Table (Table 1-1) specifies the service feature access codes, trunk
access code, station numbers and other special access codes.
Service feature...

CHAPTER 1  CUSTOMIZING OFFICE DATA
How to Customize Office Data
NEAX2000 IVS2 Office Data Programming Manual    
ND-70931 (E), Issue 2.0   Page 7
 Type of Telephone
The type of station telephone set is specified as follows:
TYPE OF TEL  
       DESCRIPTION   
DP  . . . . . . . . . . . . .  Dial Pulse Telephone set
PB  . . . . . . . . . . . . .  DTMF Telephone set
D
term . . . . . . . . . . .  Dterm set
 SERVICE CLASS-A/B/C
Specify the service class (1-15) programmed in the Service Restriction Data...