NEC Multisync P701 Users Manual

English-9
English
Terminal Panel
Out
InOut
In
RGBHVRGB/HVRGBHVDVD/HD2 Pr Y Pb
VIDEO2VIDEO
 VIDEO IN connector (BNC and RCA)
To input a composite video signal. BNC and RCA connectors
are not available at the same time (Use only one input).
  VIDEO OUT connector (BNC)
To output the composite video signal from the VIDEO IN
connector.
  DVD/HD connector (RCA)
Connecting equipment such as a DVD player, HDTV device,
or Set-Top-Box.
 S-VIDEO IN connector (Mini DIN 4 pin)
To input the S-video (Y/C separate...

English-10
 Kensington Lock
For security and theft prevention.
 EXTERNAL SPEAKER TERMINAL
To output the audio signal from AUDIO 1, 2, 3, DPORT,
HDMI and TV jack.
Note:  This speaker terminal is for 15W + 15W (8 ohm)
speaker.
 Option board slot
Slot for board accessories. Please contact your supplier for
detailed information.
 

English-11
English
 POWER button
Switches the power on/standby.
 INPUT button
Selects input signal. DVI: DVI
DISPLAYPORT: DPORT
VGA: VGA
RGB/HV: RGB/HV
HDMI: HDMI
DVD/HD: DVD/HD1, DVD/HD2, SCART
VIDEO: VIDEO1, VIDEO2
S-VIDEO: S-VIDEO
OPTION: Depends on your connection
 PICTURE MODE button
Selects picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA], [AMBIENT1], [AMBIENT2]. See page 19.
HIGHBRIGHT: for moving images such as DVD.
STANDARD: for images.
sRGB: for text based images.
CINEMA: for movies....

English-12
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor’s
remote sensor during button operation.
Use the remote control within a distance of about 7 m (23 ft.)
from remote control sensor or at a horizontal and vertical
angle of within 30° within a distance of about 3.5 m (10 ft.).
Caution:Important, the remote control
system may not function when
direct sunlight or strong
illumination strikes the remote
control sensor or when there is an
object in the...

English-13
English1. Determine the installation location
CAUTION:Installing your LCD monitor must be done by a
qualified technician. Contact your dealer for
more information.
CAUTION:
MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY FOUR OR MORE PEOPLE.
Failure to follow this caution may result in injury if
the LCD monitor falls.
CAUTION: Do not mount or operate the display upside
down, face up, or face down.
CAUTION: This LCD has a temperature sensor and cooling
fan. If the LCD becomes too hot, the...

English-14
5. Attach the cable cover
• Use six of the M4 screws (included) to attach the cablecover.
6. Switch on the power of all the attachedexternal equipment
When connected with a computer, switch on the power of
the computer first.
7. Operate the attached externalequipment
Display the signal from the desired input source.
8. Adjust the sound
Make volume adjustments when required.
9. Adjust the screen (See pages 21 and 22)
Make adjustments of the screen display position when
necessary.
10. Adjust...

English-15
English
Connections
NOTE:Do not connect/disconnect cables when turning on the monitor or other ex\
ternal equipment as this may result in a
loss of the monitor image.
NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Before making connections:
* First turn off the power of all the attached equipment and make connections.
* Refer to the user manual included with each separate piece of equipment.\
Wiring Diagram...

English-16
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to display \
your computer’s screen image.
Some video cards with a pixel clock over 162MHz may not display an image\
 correctly.
Your LCD monitor displays proper image by adjusting the factory preset ti\
ming signal automatically.

• If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.Refer to your Macintosh’s owner’s manual for more information about your computer’s video...

English-17
English
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on and wil\
l turn red or amber while powered off.
NOTE:The Main Power Switch must be in the ON position in order to power up th\
e monitor using the remote control or the
Power Button on the front of the LCD.
Power Button Main Power Switch
ON
OFF
Using the remote control
 

English-18
NORMAL: Displays the aspect ratio the same as it is sent
from the source.
FULL:  Fills entire screen.
WIDE:  Expands a 16:9 letter box signal to fill entire screen.
ZOOM (DYNAMIC):  Expands a 4:3 pictures to fill the entire
screen with non-linearity. Some of the outside image area
will be cut off due to expansion.
ZOOM
The image can be expanded beyond the active display area.
The image which is outside of active display area is not
shown.
ZOOM
ZOOM
Using Power Management
The LCD monitor...