NEC Multisync P521 Users Manual

User’s Manual
MultiSync P401
MultiSync P461
MultiSync P521
 

Index
Declaration of conformity ............................................................................................................................. English-1
Important Information ................................................................................................................................... English-2
WARNING, CAUTION ........................................................................................................................ English-2
Declaration...

English-1
English
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
Tel. No.: (630) 467-3000
Type of Product: Display Monitor
Equipment...

English-2
Important Information
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE...

English-3
EnglishFOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
•DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
•Do not spill any liquids into the cabinet or use your monitor
near water.
•Do not insert objects of any kind into the cabinet slots, as
they may touch dangerous voltage points,...

English-4
Contents
Power Cord*1
Setup ManualClamp x 3
Your new MultiSync monitor box* should contain the following:
•LCD monitor
•Power cord*
1
•Video Signal Cable
•Wireless Remote Control and AA Batteries
•Setup Manual•Cable cover
•Clamp x 3
•Screw (M4 x 10) x 9
•CD-ROM
•Thumbscrew for optional stand x 2*
2
CD-ROMScrew (M4 x 10) x 9
*Remember to save your original box and packing material to transport or ship the monitor.
*
1Type and number of power cords included will depend on the where the LCD...

English-5
EnglishThis device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty....

English-6
Attaching Mounting Accessories
The display is designed for use with the VESA mounting
system.
1. Attach Mounting Accessories
Be careful to avoid tipping monitor when attaching
accessories.
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the screen face,
place the protective sheet on the table underneath the LCD.
The protective sheet was wrapped around the LCD in the
original packaging. Make sure there is nothing on the table
that can damage the...

English-7
English
 EXIT button
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
 Remote control sensor and Power Indicator
Receives the signal from the remote control (when using the
wireless remote control). See also page 11.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF (ECO standby)
mode. Glows amber when the LCD is in POWER OFF
(standby) mode. Blinks amber when the monitor is in Power...

English-8
Terminal Panel
OutIn
Out In
RGBH VRGB/HVRGBHVDVD/HD2 Pr Y Pb
VIDEO2VIDEO
 VIDEO IN connector (BNC and RCA)
To input a composite video signal. BNC and RCA connectors
are not available at the same time (Use only one input).
 VIDEO OUT connector (BNC)
To output the composite video signal from the VIDEO IN
connector.
 DVD/HD connector (RCA)
Connecting equipment such as a DVD player, HDTV device,
or Set-Top-Box.
 S-VIDEO IN connector (Mini DIN 4 pin)
To input the S-video (Y/C separate signal)....