NEC Multisync Lcd3090wqxi Users Manual

English
English-9
Mount Flexible arm
1. Using the 4 screws from the stand removal and attach the arm to the moni\
tor(Figure F.1 ).
Caution: • When mounting, use ONLY the screws (4 pcs) that were
removed from the stand to avoid damage to the monitor or
stand.
• The monitor should only be used with an approved arm (e.g. GS mark).
• When using mounting accessories (e.g. VESA (200 x 100)) other than VESA (100 x 100), use
M4 size screws (Length: bracket thickness + 10mm).
Recommended Fasten Force: 98 -...

English-10
Controls
OSD (On-Screen Display) control buttons on the front of the monitor fu\
nction
as follows:
To access OSD menu, press the MENU button.
To change signal input, press the SELECT button.
NOTE:OSD must be closed in order to change signal input.
* The “LEFT/RIGHT” and “UP/DOWN” buttons functionality is inte\
rchangeable depending on the orientation (landscape/portrait) of the OSD.
SETTING OSD LANGUAGE
• Set the OSD language before using OSD functions.
• To access the “LANGUAGE SELECTION”...

English
English-11
Brightness/Contrast Controls
BRIGHTNESS
Adjusts the overall image and background screen brightness.
NOTE:The upper portion (higher settings) of the brightness level is adjuste\
d using the backlight output.
If a very low brightness level (low setting) is used the contrast leve\
l may be reduced. The display will
digitally compensate for low brightness level.
If this occurs, the indicator on the OSD will turn magenta.
CONTRAST
Adjusts the image brightness in relation to the...

English-12
FINE (Analog input only)
Improve focus, clarity and image stability by increasing or decreasing t\
his setting.
If the “Auto Adjust function” and the “H.Size” function do not give you a sa\
tisfactory picture setting, a fine tuning can
be performed using the “Fine” function.
For this a Moiré test pattern could be used. If the Fine value is wro\
ngly calibrated, the result would look like the left
drawing. The image should be homogeneous.
When FINE value iswrong. When FINE value is
correct....

English
English-13
HDCP CONTENT (Digital Input Only)
Selects the type of input to be used with HDCP CONTENT.
OFF: When a PC or other computer equipment is connected, select “OFF”.\
ON:  When a DVD player or other type of high definition device is connected,\
 select “ON”.
NOTE: Interlaced signals (480i, 576i, 1080i) are not supported. If you have \
any problems, please refer to the
Troubleshooting section of this User’s Manual.
VIDEO DETECT
Selects the method of video detection when more than one video...

English-14
OSD LOCK OUT
This control completely locks out access to all OSD control functions. W\
hen attempting to activate OSD controls
while in the Lock Out mode, a screen will appear indicating the OSD cont\
rols are locked out.
There are four types of OSD LOCK OUT:
OSD LOCK OUT with BRIGHTNESS and CONTRAST control: To activate the OSD Lock Out function, press
SELECT, then the “UP” button and hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then
the “UP” button and hold down...

English
English-15
Specifications
Monitor Specifications MultiSync LCD3090WQXi Monitor Notes
LCD Module Diagonal: 75.6 cm/29.8 inches Active matrix; thin film transistor (TFT)Viewable Image Size: 75.6 cm/29.8 inches liquid crystal display (LCD); 0.251 mm dot
Native Resolution (Pixel Count): 2560 x 1600 pitch; 350 cd/m
2*2 white luminence;1000:1*2 contrast ratio, typical.
Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI (with HDCP) Sync: Separate sync.TTL LevelHorizontal sync....

English-16
Features
DVI-I: The integrated interface ratified by the Digital Display Working Group (DDWG) that allows both digital and analog connectors of f of one
port. The “I” stands for integration for both digital and analog, The digital portion is DVI-based.
DVI-D:  The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between computers a nd
displays. As a digital-only connector, analog support is not provided off a DVI-D connector. As a...

English
English-17
Troubleshooting
No picture• The signal cable should be completely connected to the display card/comp\
uter.
• The display card should be completely seated in its slot.
• Check the Vacation Switch should be in the ON position.
• Front Power Switch and computer power switch should be in the ON positio\
n.
• Check to make sure that a supported mode has been selected on the displa\
y card or system being used. (Please consult display card or system manual to change graphics mode.)\
•...

English-18
Tag1 Brightness Adjusts the overall image and screen background brightness.
Press “Left” or “Right” to adjust.
When AUTO LUMINANCE is OFF or 2, the brightness level is adjusted/measured using\
percentage (%).
When AUTO LUMINANCE is 1 or 3, brightness level is adjusted/measured using cd/m
2.
This is the “Estimated Brightness” level.
Note: The upper portion (higher settings) of the brightness level is adjuste\
d using the
backlight output. If a very low brightness level (low setting) is used\...