NEC Multisync Lcd2490wuxi2 Users Manual

English-19
English
Advanced OSD
If you need detailed information about the controls, please use the advanced menu.

•Turn off your monitor.
•Turn on your monitor by pushing the “POWER” and “INPUT/SELECT” button at the same time for at least one second
simultaneously. Then press the control buttons (EXIT, LEFT, RIGHT, UP, DOWN).
•You will see the Advanced menu.
This menu is larger than the normal OSD.

•Turn off and restart your monitor in the normal way.
To make an adjustment, ensure that the tag is...

English-20 Tag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust.
(Analog input only)
G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust.
(Analog input only)
B-H.position Adjusts the position of the blue component of the image. Press “Left” or “Right” to adjust.
(Analog input only)
R-FINE Adjusts the “FINE” setting of the RED component of the image.
(Analog input only) Press “Left” or “Right” to...

English-21
English
H. Size Adjusts the horizontal size of the screen.
(Analog input only) If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further
tuning can be performed using the “H.Size (V.Size)” function (dot clock). For this a Moiré
test pattern could be used. This function may alter the width of the picture. Use left/Right
Menu to center the image on the screen. If the H.Size (V.Size) is wrongly calibrated, the
result would look like the left drawing. The image should...

English-22 Tag6 Color Control Color Control Systems: Seven preset color settings.
For preset settings 1, 2, 3 and 5, the following levels can be adjusted:
TEMPERATURE: Adjust the white temperature by increasing or decreasing this setting.
A lower color temperature will make the screen reddish and a higher color temperature
will make the screen bluish.
WHITE (White Balance): If TEMPERATURE needs further adjustment; the individual
R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B...

English-23
English
OFF MODE The Intelligent Power Manager allows the monitor to enter into a power saving mode after
a period of inactivity. The OFF MODE has three settings.
OFF: Monitor does not go into power save mode when the input signal is lost.
STANDARD: Monitor enters power save mode automatically when the input signal is lost.
OPTION: Monitor enters power save mode automatically when the amount of surrounding
light goes below the level that is determined by the user.
OFF MODE Setting Adjusts the...

English-24 Signal Information Signal information can be displayed in the corner of the screen.
Signal information is either “On/Off”.
Resolution Notifier The optimal resolution is 1920 x 1200. If ON is selected, a message will appear on the
screen after 30 seconds, notifying you that the resolution is not set to 1920 x 1200.
Press “Left” or “Right” to select.
Hot Key When this function is activated; the brightness and contrast of the monitor can be adjusted
without entering the OSD menu by using the...

English-25
English
TagA Tile Matrix The Tile Matrix feature allows one image to be displayed over multiple screens. This
feature can be used with up to 25 monitors (5 vertical and 5 horizontal). Using Tile Matrix
requires the PC output signal be sent through a distribution amplifier to each individual
monitor.
H MONITOR: Select the number of horizontal displays.
V MONITOR: Select the number of vertical displays.
MONITOR No: Select a position to expand the screen.
TILE COMP: Works in tandem with Tile...

English-26
Using the Auto Brightness function
The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the
room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim
accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting
conditions.
The Auto Brightness function is set to OFF by default.
NOTE: When “AUTO LUMINANCE”...

English-27
English
Using the PICTURE MODE function
Choose the Picture mode that is most suitable for the type of content that is shown.
There are five types of mode (STANDARD, sRGB, PROGRAMMABLE, Adobe® RGB (LCD2690WUXi2 only) and MEDICAL).
•To access the Picture mode, press Reset button while OSD menu is not showing.
•To select the mode, press the Left or Right button.
•To exit the PICTURE MODE, press the EXIT button.
NOTE:When selecting the Adobe
® RGB (LCD2690WUXi2 only) or MEDICAL mode, press the...

English-28
TCO’03
Congratulations!
The display you have just purchased carries the TCO’03 Displays
label. This means that your display is designed, manufactured and
tested according to some of the strictest quality and environmental
requirements in the world. This makes for a high performance
product, designed with the user in focus that also minimizes the
impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
•Good visual ergonomics and image quality in...