NEC Multisync Lcd2470wnx Users Manual

MultiSync LCD2470WNX
User’s Manual
 

Index
Warning, Caution ......................................................................................................................... English-1
Declaration ................................................................................................................................... English-1
Canadian Department of Communications Compliance Statement ............................................. English-2
Declaration of Conformity...

English
English-1
WARNING
CAUTION
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of...

English-2
Canadian Department of Communications Compliance
Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync LCD2470WNX (L246H3) colour monitor so as not to interfere with
radio and television reception.
(1) The power supply cord you use...

English
English-3
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
•MultiSync LCD monitor with tilt/swivel/height adjust stand
•Power Cord
•Cable cover
•Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
•Video Signal Cable (DVI-D to DVI-D)
•USB Cable
•User’s Manual
•CD ROM (includes complete User’s Manual in PDF format).
To see the User’s Manual, Acrobat Reader 4.0 or higher must be installed on your PC.
Power Cord
User’s Manual15-pin mini D-SUB male to...

English-4
Quick Start
To attach the MultiSync LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2.For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your
system (Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your
system (Figure A.2). Tighten all screws.
For the MAC: Connect the Macintosh cable adapter...

English
English-5
D-SUB Cable
Power Cord FlatUSB Cable Power Cord DC-OUT
NEC optional product attachment.
Do not use this connector unless specified.Input1 (DVI) Input2 (D-Sub)
DVI Cable
Figure C.4
Figure C.6
Figure C.7
Figure C.4a
7. Place the connector cover onto the back cabinet (Figure C.5).
8. For successful cable management, place the cables into the cable management in this
order: Power cord and DVI cable (Figure C.6).
9. Place DVI and Power cord into the specific hooks, as indicated in Figure...

English-6
14. Connect the power cord to the power outlet (Figure E.1).
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it, as show in
Figure E.2.
NOTE:Please refer to Caution section of this manual for proper selection of AC power cord.
15. Turn on the monitor with the front power button and the computer (Figure E.1).
16. No-Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.
For further...

English
English-7
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Place hands on each side of the monitor and lift up to the highest position. Remove the cable cover (Figure S.1).
Remove the connector cover (Figure S.2).
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it,
as shown in the figure beside.
2. Disconnect all cables.
3. Place monitor face down on a non-abrasive surface (Figure S.3).
NOTE:Handle...

English-8
Figure S.4
5. Remove the stand (Figure S.4).
The monitor is now ready for mounting in an alternate manner.
6. Connect the cables to the back of the monitor.
7. Reverse this process to re-attach stand.
NOTE:Use only VESA-compatible alternative mounting method.
Handle with care when removing stand.
Flexible Arm Installation
This LCD monitor is designed for use with a flexible arm. To mount the monitor to a flexible arm:
1. Follow the instructions on how Remove Monitor Stand for Mounting to remove...