NEC Multisync Lcd2070wnx Users Manual

MultiSync LCD2070WNX
User’s Manual
 

Index
Warning, Caution ........................................................................................................................ English-1
Declaration .................................................................................................................................. English-1
Canadian Department of Communications Compliance Statement ........................................... English-2
Declaration of Conformity...

English
English-1
WARNING
CAUTION
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of...

English-2
Canadian Department of Communications Compliance
Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1.Use the attached specified cables with the MultiSync LCD2070WNX (L205GX) colour monitor so as not to interfere
with radio and television reception.
(1) The power supply cord you use...

English
English-3
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
•MultiSync LCD2070WNX monitor with tilt/swivel adjust stand
•Power Cord
•Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
•Video Signal Cable (DVI-D to DVI-D)
•USB Cable
•User’s Manual
•Cable Cover
•CD ROM (includes complete User’s Manual in PDF format).
To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.
Power Cord
User’s Manual 15-pin mini D-SUB male to
15-pin...

English-4
Quick Start
To attach the MultiSync LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2.For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your
system (Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your
system (Figure A.2). Tighten all screws.
For the MAC: Connect the Macintosh cable adapter...

English
English-5
11. Hold all cables firmly and place the cable cover onto the stand (Figure C.5). To remove the cable cover, lift the cover off as
shown in Figure C.6.
12. Connect the power cord to the power outlet (Figure D.1).
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it, as shown in
Figure D.2.
NOTE:Please refer to Caution section of this manual for proper selection of AC power cord.
13. The vacation switch on the back side of the monitor...

English-6
Figure M.1
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Place hands on each side of the monitor to lift up to the highest position.
Remove the cable cover (Figure M.1).
Remove the connector cover (Figure M.2).
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it,
as shown in the figure beside.
2. Disconnect all cables.
Figure M.2
Figure RL.1
Raise and Lower Monitor Screen
The monitor may be raised...

English
English-7
Figure M.4
3. Place monitor face down on a non-abrasive surface (Figure M.3).
NOTE:Handle with care when monitor facing down, for avoiding the damage to the front buttons.
4. Remove the 4 screws connecting the stand to the monitor (Figure M.3).
5. Remove the stand (Figure M.4). The monitor is now ready for mounting in an alternate manner.
6. Connect the cables and place the connector cover on the back of the monitor.
7. Reverse this process to re-attach stand.
NOTE:Use only...

English-8
Controls
OSM (On-Screen Manager) control buttons on the front of the monitor
function as follows:
To access OSM menu, press any of the control buttons (MENU/EXIT, Left, Right, Down, Up).
To change signal input, press the SELECT button.
To change DV MODE, press the RESET/DV MODE button.
NOTE:OSM must be closed in order to change signal input.
NOTE:When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the
RESET function by pressing the MENU/EXIT...