NEC Multisync E201w Users Manual

MultiSync E201W
User’s Manual
 

Index
Warning, Caution ........................................................................\
................................................. English-1
Registration Information ........................................................................\
....................................... English-1
Recommended use ........................................................................\
.............................................. English-3
Contents...

English
English-1
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROMWALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have\
 sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of...

English-2
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian In\
terference-Causing Equipment Regulations.
C-UL:  Bears the C-UL Mark and is in compliance with Canadian Safety Regulatio\
ns according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync E201W (L200NX) co\
lor monitor so as not to interfere with radio
and television reception.
(1) The power supply cord you use...

English
English-3
Recommended use
Safety Precautions and MaintenanceFOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR:
• DO NOT OPEN THE MONITOR.  There are no user serviceable parts inside and opening or removing cover\
s may expose
you to dangerous shock hazards or other risks. Refer all servicing to qu\
alified service personnel.
• Do not spill any liquids into the cabinet or use your monitor near water\
.
• Do not insert objects of any kind...

English-4
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CANREDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR:
• For optimum performance, allow 20 minutes for warm-up.
• Adjust the monitor height so that the top of the screen is at or slightl\
y below eye level. Your eyes should look slightly downward when viewing the middle of the sc\
reen.
• Position your monitor no closer than 40 cm and no further away than 70 c\
m from your eyes. The optimal distance is 50 cm....

English
English-5
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
• MultiSync LCD monitor with tilt/swivel/pivot/height adjust base
• Power Cord
• Base
• Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
• Video Signal Cable (DVI-D to DVI-D)
• Setup Manual
Power Cord
(Type of power cord included will depend on the where the
LCD monitor is to be shipped)
Setup Manual 15-pin mini D-SUB male to
15-pin mini D-SUB male DVI-D to DVI-D
*Remember to save your...

English-6
Quick Start
To attach the Base to the LCD stand:
1. Place monitor face down on a non-abrasive surface (Figure 1).
NOTE: Handle with care when monitor facing down, for avoiding damage to the fr\
ont
control buttons.
2. Please rotate the stand 90 degrees as shown in  Figure 1.
NOTE: Handle with care when pulling the stand.
3. Attach the base to the stand and lock screw at the base’s bottom ( Figure 2).
NOTE: Reverse this procedure if you need to re-pack the monitor.
To attach the MultiSync LCD...

English
English-7
Figure C.1
Power Button
Figure RL.1
Raise and Lower Monitor Screen
The monitor may be raised or lowered. To raise or lower screen, place hands on each side of the monitor and lif\
t or lower to
the desired height (Figure RL.1).
NOTE: Handle with care when raising or lowering the monitor screen.
Tilt and Swivel
Grasp both sides of the monitor screen with your hands and adjust the ti\
lt and swivel as desired ( Figure TS.1).
NOTE: Handle with care when tilting the monitor screen.
Figure...

English-8
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Disconnect all cables.
2. Place monitor face down on a non-abrasive surface (Figure S.1).
NOTE: Handle with care when monitor facing down, for avoiding damage to the fr\
ont control buttons.
3. Remove the 4 screws connecting the stand to the monitor ( Figure S.1).
NOTE: In order to avoid stand drop, when removing screws, please support stand\
 with your hand.
Screen Rotation
Before rotating, the screen...