NEC Multeos M401 Users Manual

							
English-29
EnglishThis LCD monitor can be controlled by connecting a personal computer wit\
h a RS-232C terminal.
NOTE:When you use this function, EXTERNAL CONTROL should be “RS-232C” (\
See page 23).
Functions that can be controlled by a personal computer are:
• Power ON or OFF
• Switching between input signals
Connection
LCD Monitor + PC
NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your
dealer for details.
* In order to function, the RS-232C OUT terminal can only be connected to \
another monitor of the same model. Do not connect to other types of equipment.
To control monitor or multiple monitors that are daisy-chained together p\
lease use the control command. Instructions for the
control command can be found on the CD included with the display. The file is called “External_control.pdf”.
1) Interface
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
The reverse type cable (null modem cable) (not included) should be u\
sed for RS-232C control.
2) Control command diagram Please see file “External_Control.pdf” on the CD-ROM.
PROTOCOL RS-232C
BAUD RATE 9600  [bps]
DATA LENGTH 8  [bits]
PARITY BIT NONE
STOP BIT 1 [bit]
FLOW CONTROL NONE
RS-232C Cable
PC
(Out)
RS-232C CableRS-232C (OUT)
MULTEOS
RS-232C (IN)
RS-232C (OUT)
RS-232C (IN)
IN OUT MULTEOS
Controlling the LCD monitor via RS-232C Remote Control
MULTEOS
 
						

							
English-30
Connecting to a Network
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.
NOTE:When you use this function, EXTERNAL CONTROL should be “LAN” (See\
 page 23).
To use a LAN connection, you are required to assign an IP address.
Example of LAN connection:
Controlling the LCD monitor via LAN Control
Server
Hub NOTE: Use a category 5 or higher LAN cable.
LAN cable
(not supplied)
Network Setting by Using an HTTP Browser
Overview
Connecting the monitor to a network allows for monitor control from a co\
mputer via the network.
To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.
The IP address and subnet mask of the monitor can be set on the Network \
Setting screen of the web browser by using an
HTTP server function. Please be sure to use “Microsoft Internet Explorer \
6.0” or a higher version for the web browser.
(This device uses “JavaScript” and “Cookies” and the browse\
r should be set to accept these functions. The setting method will
vary depending on the version of browser. Please refer to the help files and the other information provided in y\
our software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the
monitor and entering the following URL.
Network Setting
http:///index.html
TIP: The default IP address is “192.168.0.10”.
The exclusive application can be downloaded from our website.
NOTE: If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to
refresh your web browser (or clear the cache).
The display or button’s response can be slowed down or operation may not be accepted depending\
 the settings of
your network.
Should this happen, consult your network administrator.
The LCD monitor may not respond if its buttons are repeatedly pressed in\
 rapid intervals. Should this happen, wait a
moment and repeat.
If you still can’t get a response, turn off and back on the monitor.
 
						

							
English-31
English
Preparation Before Use
Connect the monitor to a commercially available LAN cable before engagin\
g in browser operations.
Operation with a browser that uses a proxy server may not be possible de\
pending on the type of proxy server and the setting
method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be
displayed depending on the effectiveness of the cache, and the contents set from the browser may not \
be reflected in
operation. It is recommended that a proxy server not be used unless it i\
s unavailable.
Handling of the Address for Operation via a Browser
Regarding the actual address that is entered for the address or entered \
into the URL column when operation of the monitor is
via a browser, the host name can be used as it is when the host name corresponding to\
 the IP address of the monitor has
been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of
the monitor has been set in the “HOSTS” file of the computer being\
 used.
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, \
access is gained to the network setting byspecifying 
http://pd.nec.co.jp/index.html for the address or the entry column of the URL.
Example 2: When the IP address of the monitor is “192.168.73.1”, access is ga\
ined to the mail alert settings by specifying
http://192.168.73.1/index.html for the address or the entry column of the URL.
Network Settings
http:// /index.html
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet ma\
sk number obtained from
your network administrator.
NOTE: The IP address of the monitor is required to change the network setting.\
 The IP address will not be displayed on the Monitor’s menu.
Consult your network administrator for the IP address when [ENABLE] is s\
elected for
[DHCP].
Set your IP address of the network connected to the monitor when [DISABL\
E] is selected for
[DHCP].
Set your subnet mask number of the network connected to the monitor when\
 [DISABLE] is selected
for [DHCP].
Set your default gateway of the network connected to the monitor when [D\
ISABLE] is selected for
[DHCP].
Set your primary DNS settings of the network connected to the monitor.
Set your secondary DNS settings of the network connected to the monitor.
Reflect your settings.
NOTE: Close the browser after clicking [UPDATE]. The monitor will automatically update your settings.
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS (PRIMARY)
DNS (SECONDARY)
UPDATE
 
						

							
English-32
Alert Mail Setting
http:///lanconfig.htmlType in the hostname of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
Type in the domain name of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
Checking [ENABLE] will turn on the Alert Mail feature.
Checking [DISABLE] will turn off the Alert Mail feature.
Type in the senders address. Up to 60 alphanumeric and symbols characters\
 can be used.
Type in the SMTP server name to be connected to the monitor.
Up to 60 alphanumeric characters can be used.
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
Click this button to reflect the above settings.
Click this button to send a test mail to check if your settings are corr\
ect.
A reply to a test mail will be displayed.
HOST NAME
DOMAIN NAME
ALERT MAIL
SENDER’S ADDRESS
SMTP SERVER NAME
RECIPIENT’S
ADDRESS 1 to 3
APPLY
EXECUTE
STATUS
This option notifies your computer of an error message via e-mail when u\
sing wired LAN. An error message notification will be
sent when an error occurs in the monitor.
NOTE:
• If you execute a test, you may not receive an Alert mail.
Should this happen, check if the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient’s Address is correct.
TIP: The Alert Mail settings will not be affected even when [RESET] is done from the menu.
For Control command diagram, please see file “External_Control.pdf”\
 on the CD-ROM.
 
						

							
English-33
EnglishReduced Footprint: Provides the ideal solution for environments requiring superior image qu\
ality but with size and weight
limitations.
Color Control Systems:  Allows you to adjust the colors on your screen and customize the color a\
ccuracy of your monitor to
a variety of standards.
OmniColor:  Combines Six-axis color control and the sRGB standard. Six-axis color c\
ontrol permits color adjustments via six
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously availab\
le. The sRGB standard provides
the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the sa\
me as on the
color printout (with sRGB supporting operating system and sRGB printer)\
. This allows you to adjust the colors on your screen
and customise the color accuracy of your monitor to a variety of standar\
ds.
sRGB Color Control:  A new optimized color management standard which allows for color matching\
 on computer displays
and other peripherals. The sRGB standard, which is based on a calibrated color space, allows fo\
r optimal color representation
and backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls:  Allow you to quickly and easily adjust all elements of your screen image\
 via simple to
use on-screen menus.
Plug and Play:  The Microsoft
® solution with the Windows® operating system facilitates setup and installation by allowing the
monitor to send its  capabilities (such as screen size and resolutions supported) directly \
to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System:  Provides innovative power-saving methods that allow the monitor to shift\
 to a
lower power consumption level when on but not in use, saving two-thirds \
of your monitor energy costs, reducing emissions
and lowering the air conditioning costs of the workplace.
FullScan Capability:  Allows you to use the entire screen area in most resolutions, significan\
tly expanding image size.
VESA Standard (FDMIv1) Mounting Interface:  Allows users to connect their LCD monitor to any VESA standard (FDMIv1)
third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third\
 party compliant
device. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.
DVI-D:  The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between
computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based
digital only connection, only a simple adapter is necessary for compatib\
ility between DVI-D and other DVI-based digital
connectors such as DFP and P&D. The DVI interface of this display supports HDCP.
TILE MATRIX, TILE COMP:  Shows one image over multiple screens with accuracy while compensating f\
or bezel width.
ZOOM:  Expands image size for horizontal and vertical direction.
RS-232C daisy chain:  You can control the multiple monitors by controller or wireless remote co\
ntroller.
Self-diagnosis:  If an internal error should occur, a failure state will be indicated.
Long cable capability:  Automatic long cable compensation prevents image quality degradation (d\
ull signals) caused by long
cable lengths.
Features
 
						

							
English-34
No picture
• The signal cable should be completely connected to the
display card/computer.
• The display card should be completely seated in its slot.
• Front Power Switch and computer power switch should be in the ON position.
• Check to make sure that a supported mode has been selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
• Check the monitor and your display card with respect to compatibility and recommended settings.
• Check the signal cable connector for bent or pushed-in pins.
Power Button does not respond
• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
Image persistence
• Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of a
previous image remains visible on the screen. Unlike
CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a
long period of time should be avoided. To alleviate image
persistence, turn off the monitor for as long as the
previous image was displayed. For example, if an image
was on the monitor for one hour and a residual image
remains, the monitor should be turned off for one hour to
erase the image.
NOTE: As with all personal display devices, NEC DISPLAY
SOLUTIONS recommends displaying moving
images and using a moving screen saver at regular
intervals whenever the screen is idle or turning off
the monitor when not in use.
Image is unstable, unfocused or swimming is apparent
• Signal cable should be completely attached to the computer.
• Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image
Adjust settings may need to be re-adjusted.
• Check the monitor and your display card with respect to compatibility and recommended signal timings.
• If your text is garbled, change the video mode to non- interlace and use 60Hz refresh rate.
Image of component signal is greenish
• Check to see if the DVD/HD input connector is selected.
LED on monitor is not lit
(no green or red color can be seen)
• Power Switch should be in the ON position and power cord should be connected.
• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). RED LED on monitor is blinking
• A certain failure might have occurred, please contact
your nearest authorized NEC DISPLAY SOLUTIONS
service facility.
• If the monitor is powered off by the inside temperature being higher than the normal operating temperature, a
RED LED will blink six times. Power on the display again
after confirming the inside temperature has been
reduced to normal operation temperature.
Display image is not sized properly
• Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.
• Check to make sure that a supported mode has been selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
Selected resolution is not displayed properly
• Use OSD Display Mode to enter Information menu and confirm that the appropriate resolution has been
selected. If not, select corresponding option.
No Sound
• Check to see if audio cable is properly connected.
• Check to see if mute is activated.
• Check to see if volume is set at minimum.
• Check to see if computer supports an audio signal through DisplayPort.
If unsure, contact the computer manufacturer.
Remote Control is not available
• Check the Remote Control’s batteries status.
• Check if batteries are inserted correctly.
• Check if the Remote Control is pointing at the monitor’s remote sensor.
• Check the Remote Control Mode status.
• The remote control system may not function when direct sunlight or strong illumination strikes the remote control
sensor of the LCD monitor, or when there is an object in
the path.
“SCHEDULE”/“OFF TIMER” function is not working
properly
• The “SCHEDULE” function will be disabled when the “OFF TIMER” is set.
• If the “OFF TIMER” function is enabled and the power to the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be
reset.
Snowy Picture, Poor Sound in TV
• Check antenna/cable connection. Use new cable if necessary.
Interference in TV
• Check components for shielding, move away from monitor if necessary.
RS-232C or LAN control is not available
• Check RS-232C or LAN cable connection.
• Check “CONTROL” setting in “EXTERNAL CONTROL”.
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or
degradation.
Troubleshooting
 
						

							
English-35
English
Specifications - M401
Product Specifications
LCD Module 40" /101.6 cm diagonalPixel Pitch: 0.461 mm
Resolution: 1920 x 1080 Color: Over 16 million colors (depending on video card used)
Brightness: 450 cd/m
2
Contrast Ratio: 4000:1 Viewing Angle: 89° (typ) @ CR>10
Design View Distance: 1100 mm
Frequency Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input)
Vertical: 50.0 - 85.0 Hz
Pixel Clock 25.2 MHz - 162.0 MHz
Viewable Size 885.6 x 498.2 mm
Input Signal
DVI DVI-D 24pin Digital RGB DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
DisplayPort DisplayPort Connector Digital RGB DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz)
VGA 15pin Mini D-sub Analog RGB 0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI HDMI Connector Digital RGB HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD1 RCA (Y, Cb/Pb, Cr/Pr) Component Y: 1.0 Vp-p/75 ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
DVD/HD2 BNC HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,\
 480i@60Hz
VIDEO1 BNC/RCA Composite 1.0 Vp-p/75 ohm
VIDEO2 BNC NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO Mini DIN 4 pin S-VIDEO Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
Output Signal
RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
DVD/HD2 BNC Component Y: 1.0 Vp-p/75 ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
VIDEO1/VIDEO2BNC Composite 1.0 Vp-p with 75 ohm terminated
AUDIOAUDIO RCA (L/R) X2 Analog Audio Stereo L/R 0.5 Vrms
Input STEREO Mini Jack
HDMI Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit)
DisplayPort Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit)
AUDIO RCA (L/R) Analog Audio Stereo L/R 0.5 Vrms
Output
Speaker Output External Speaker Jack 15 W + 15 W (8 ohm)
Control RS-232C In: 9 Pin D-sub RS-232C Out: 9 Pin D-sub (with daisy chain)LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5 
Remote OUT: Stereo Mini jack 3.5 
Power Supply 3.5 - 1.45 A @ 100-240VAC, 50/60Hz
Operational Environment Temperature: 5 - 40°C / 41 - 104°F Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension 981.8 (W) x 582.4 (H) x 142.5 (D) mm / 38.7 (W) x 22.9 (H) x 5\
.6 (D) inches
Weight 25.0 Kg (55.1 lbs)
VESA compatible arm mounting interface 300 mm x 300 mm (M6, 4 Holes)
Power Management VESA DPM
Plug & Play VESA DDC2B, DDC/CI, DisplayPort
Accessories Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp, Screw,
CD-ROM
NOTE:  Technical specifications are subject to change without notice. *1: Compressed image
 
						

							
English-36
Specifications - M461
Product Specifications
LCD Module 46" /116.8 cm diagonalPixel Pitch: 0.530 mm
Resolution: 1920 x 1080 Color: Over 16 million colors (depending on video card used)
Brightness: 450 cd/m
2
Contrast Ratio: 4000:1 Viewing Angle: 89° (typ) @ CR>10
Design View Distance: 1300 mm
Frequency Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input)
Vertical: 50.0 - 85.0 Hz
Pixel Clock 25.2 MHz - 162.0 MHz
Viewable Size 1018.1 x 572.7 mm
Input Signal
DVI DVI-D 24pin Digital RGB DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
DisplayPort DisplayPort Connector Digital RGB DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz)
VGA 15pin Mini D-sub Analog RGB 0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI HDMI Connector Digital RGB HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD1 RCA (Y, Cb/Pb, Cr/Pr) Component Y: 1.0 Vp-p/75 ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
DVD/HD2 BNC HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,\
 480i@60Hz
VIDEO1 BNC/RCA Composite 1.0 Vp-p/75 ohm
VIDEO2 BNC NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO Mini DIN 4 pin S-VIDEO Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
Output Signal
RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
DVD/HD2 BNC Component Y: 1.0 Vp-p/75 ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
VIDEO1/VIDEO2BNC Composite 1.0 Vp-p with 75 ohm terminated
AUDIOAUDIO RCA (L/R) X2 Analog Audio Stereo L/R 0.5 Vrms
Input STEREO Mini Jack
HDMI Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit)
DisplayPort Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit)
AUDIO RCA (L/R) Analog Audio Stereo L/R 0.5 Vrms
Output
Speaker Output External Speaker Jack 15 W + 15 W (8 ohm)
Control RS-232C In: 9 Pin D-sub RS-232C Out: 9 Pin D-sub (with daisy chain)LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5 
Remote OUT: Stereo Mini jack 3.5 
Power Supply 3.9 - 1.6 A @ 100-240VAC, 50/60Hz
Operational Environment Temperature: 5 - 40°C / 41 - 104°F Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension 1112.8 (W) x 659.4 (H) x 142.5 (D) mm / 43.8 (W) x 26.0 (H) x 5.\
6 (D) inches
Weight 29.8 Kg (65.7 lbs)
VESA compatible arm mounting interface 300 mm x 300 mm (M6, 4 Holes)
Power Management VESA DPM
Plug & Play VESA DDC2B, DDC/CI, DisplayPort
Accessories Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp, Screw,
CD-ROM
NOTE:  Technical specifications are subject to change without notice.  *1: Compressed image
 
						

							
English-37
English
Specifications - M521
Product Specifications
LCD Module 52"/132.1 cm diagonalPixel Pitch: 0.6 mm
Resolution: 1920 x 1080 Color: Over 16 million colors (depending on video card used)
Brightness: 500 cd/m
2 (typ)
Contrast Ratio: 3000:1 Viewing Angle: 89° (typ) @ CR>10
Design View Distance: 1100 mm/43.3 inches
Frequency Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input)
Vertical: 50.0 - 85.0 Hz
Pixel Clock 25.2 MHz - 162.0 MHz
Viewable Size 1152 x 648 mm
Input Signal
DVI DVI-D 24pin Digital RGB DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
DisplayPort DisplayPort Connector Digital RGB DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz)
VGA 15pin Mini D-sub Analog RGB 0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI HDMI Connector Digital RGB HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD1 RCA (Y, Cb/Pb, Cr/Pr) Component Y: 1.0 Vp-p/75 ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
DVD/HD2 BNC HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,\
 480i@60Hz
VIDEO1 BNC/RCA Composite 1.0 Vp-p/75 ohm
VIDEO2 BNC NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO Mini DIN 4 pin S-VIDEO Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
Output Signal
RGB/HV BNC (R,G,B,H,V) Analog RGB 0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
DVD/HD2 BNC Component Y: 1.0 Vp-p/75 ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
VIDEO1/VIDEO2BNC Composite 1.0 Vp-p with 75 ohm terminated
AUDIOAUDIO RCA (L/R) X2 Analog Audio Stereo L/R 0.5 Vrms
Input STEREO Mini Jack
HDMI Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit)
DisplayPort Connector Digital Audio PCM 32, 44.1, 48 KHz (16/20/24bit)
AUDIO RCA (L/R) Analog Audio Stereo L/R 0.5 Vrms
Output
Speaker Output External Speaker Jack 15 W + 15 W (8 ohm)
Control RS-232C In: 9 Pin D-sub RS-232C Out: 9 Pin D-sub (with daisy chain)LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5 
Remote OUT: Stereo Mini jack 3.5 
Power Supply 4.9 - 2.0 A @ 100-240VAC, 50/60Hz
Operational Environment Temperature: 5 - 40°C / 41 - 104°F Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension 1261.8 (W) x 752 (H) x 144.3 (D) mm / 49.7 (W) x 29.6 (H) x 5.\
7 (D) inches
Weight 38.6 Kg (85.1 lbs)
VESA compatible arm mounting interface 400 mm x 400 mm (M6, 4 Holes)
Power Management VESA DPM
Plug & Play VESA DDC2B, DDC/CI, DisplayPort
Accessories Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp, Screw,
CD-ROM
NOTE:  Technical specifications are subject to change without notice. *1: Compressed image
 
						

							
English-38
1) RS-232C input/output
Pin No Name
1 connected to 7&8
2 RXD
3 TXD
4 connected to 6
5 GND
6 connected to 4
7 connected to 1&8
8 connected to 1&7
9NC
1
6 5
9
D-SUB 9P
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
2) REMOTE IN
Pin Assignment
3) REMOTE OUT