NEC Mt830+ Projector Users Manual

							31
REMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
REMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
Connecting Your Computer to the
Mouse Output Port
The built-in remote mouse receiver enables you to operate your
computers mouse functions from the NEC MultiSync MT830+/
MT1030+/MT1035+ remote control. It is a great convenience for
clicking through your computer-generated presentations.
To connect the mouse output port:
1. Turn off your computer.
2. For PCs: Remove your current mouse and connect the serial
cable from the mouse output to your PCs mouse port. (Use the
6-pin adapter for connecting to a PS/2 computer.)
For Macintosh: Remove your current mouse from your com-
puter, attach the Macintosh adapter to the mouse output portÕs
serial cable, and connect the LCD Projector to your mouse port.
3. When the built-in remote mouse receiver is available, it will
disable your regular mouse, disconnect the serial cable and
restart your computer.
IBM PC/AT
IBM PS/2 Macintosh
INSTALLATION59
60 mThe built-in Remote Mouse Receiver as a mouse for your computer
Serial cable (supplied) 
						

							32
This section describes how to select a computer or video source and how to adjust
the picture and sound.
General Controls Before you turn on your MultiSync MT830+/MT1030+/
MT1035+ LCD Projector,  ensure that the computer or video source is turned on
and that your lens cap is removed.
1.Turn On The LCD Projector The main power switch is on the front panel of
the MultiSync MT830+/MT1030+/MT1035+ LCD Projector. By turning this
switch on, the projector will go into its standby mode and the power light will
glow amber. Only after you press the On button on the remote control or
projector cabinet will the power light turn to green and the projector become
ready to use.
NOTE: To turn the LCD projector on and off with just the front panel switch,
use the menu and enable the auto start feature. (See page 71. )
2.Select The Computer, Video Source Or ÒPresentation ViewerÓ Press the
ÒVideoÓ (VCR, document camera, or laser disc player), ÒS-videoÓ, ÒRGB 1Ó or
ÒRGB 2Ó (computer) or PC CARD button on the remote control to display the
image. Or press the ÒMenuÓ button on the cabinet and use the icons to select
your video source: ÒVideoÓ, ÒS-VideoÓ, ÒRGB 1Ó, ÒRGB 2Ó or ÒPC CARDÓ.
OPERATION 3
3.Adjust The Image Size Press the Zoom button (+) or (-) on the remote control
or projector cabinet to make the image larger or smaller.
4.Focus Press the Focus button (+) or (-) on the remote control or projector
cabinet to focus the image.
5.Turning Off The Projector First press the off button on the remote control or
the projector cabinet. The power light will glow amber. Then turn off the main
power switch on the front panel. The power light will go out.
IMPORTANT:
¥ The LCD projector should be unplugged if it will not to be used for an extended
period.
¥ To turn off the image briefly (five minutes or less), use the Picture Mute button
instead of turning the projector off and on.
¥ The LCD projector will display a black or blue image if no input signal is present.
¥ Do not turn the LCD projector off and then immediately back on. The projector
needs to cool for a minute before it can be restarted.
OPERATION61
62 
						

							33
aaaaaaaaaaaaaa aaaaaaa
Using The Menus
1. Press the Menu button on the remote control or projector cabinet to display the Main Menu.
2. Press the Select button on the projector cabinet or (s) (t) buttons on your remote control to highlight the menu for the item you want
to adjust.
3. Press the Enter button on the projector cabinet or the Left Click button on the remote control to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using the Mouse pad (+) or (Ð) buttons on the remote control or ÒSelectÓ (+) or (Ð)
buttons on the cabinet. The on-screen gauge will show you the amount of increase or decrease. [The (+) button is on and (Ð) is off.]
5. The change is stored until you adjust it again.
6. Repeat steps 2-5 to adjust an additional item, or press Right-Click on your remote control to quit the menu display.
OPERATION63
64
VIDEO RGB Auto Mode ON RGB Auto Mode OFFPC CARD 
						

							34
Menu Descriptions & Functions
Source Menu
OPERATION65
66 Enables you to select a video source such as a VCR, DVD player, laser disc player, computer
or document camera depending on what is connected to your inputs. Press the Select
button on the projector cabinet or (s) (t) buttons on your remote control to highlight the
menu for the item you want to adjust
Video
Selects what is connected to your Video input-VCR, laser disc player, DVD player, or
document camera.
S-Video
Selects what is connected to your S-Video input-VCR, DVD player, or laser disc player.
RGB 1
Selects the computer connected to your RGB 1 input.
RGB 2
Selects the computer connected to your RGB 2 input.
NOTE: Normally select the Auto mode so that the LCD projector automatically can select
the appropriate resolution mode for your RGB source.
If you want to finely adjust the image or if the LCD projector fails to select the appropriate
resolution mode for the RGB source, turn the Auto mode off and select the Real mode on the
Resolution item.
PC CARD
This feature enables you to make a presentation using the Viewer function with the optional
MT Viewer board (VK-MT) installed.
Press the Mouse pad (+) or (-) buttons to select Start for the image you want to display
first and Select File for the file you want to select or Select Slide for the image you want
to slide. 
						

							35
Image Adjustment
Menu
OPERATION67
68 Provides access to controls for your image and sound. Use the ÒSelectÓ button on the projector cabinet or (s)
(t) buttons on your remote control to highlight the menu for the item you want to adjust.
The volume, image mode, keystone, brightness, contrast, color, tint and sharpness controls are available for
Video or S-Video sources.
The volume, image mode, keystone, brightness, contrast, white balance and auto mode controls are available for
RGB 1 or RGB 2 sources.
The volume, image mode and keystone controls are available for PC CARD.
Volume
Use the Mouse pad (+) or (Ð) buttons to adjust the volume.
Image Mode
.
VIDEO/S-VIDEO........ Use the Mouse pad (+) or (-) buttons to choose Normal for a regular picture, Natural
for true color reproduction, or Document Camera for a document camera or other low
APL picture.
RGB/ PC CARD .....Use the Mouse pad (+) or (-) buttons to choose Normal when in a lighted room and
Natural 1&2 when in a darkened room. 1 for better flesh tone; 2 for true reproduction of
middle tones.
Keystone
Use the Mouse pad (+) or (-) buttons to correct the keystone (trapezoidal) distortion to make the top of the
screen longer or shorter to be the same as the bottom.
NOTE: The maximum keystone angle that can be corrected is 23 degrees, including the optical offset 8 degrees.
NOTE: To save your keystone changes, select Keystone Save from the Power Menu.
Brightness
Use the Mouse pad (+) or (Ð) buttons to adjust the brightness.
Contrast
Use the Mouse pad (+) or (Ð) buttons to adjust the contrast.
Color
..
 Use the Mouse pad (+) or (Ð) buttons to adjust the color.
Tint
..
Use the Mouse pad (+) or (Ð) buttons to adjust the tint.
Sharpness
..
Use the Mouse pad (+) or (Ð) buttons to adjust the sharpness. 
						

							36OPERATION69
70 White Balance
...
Use the Mouse pad (+) or (-) buttons to adjust the white balance. Brightness for each color (RGB) is used to
adjust the black level of the screen; Contrast for each color (RGB) to adjust the white level of the screen.
Auto Mode
...
Use the Mouse pad (+) button to turn this feature on so Horizontal Position, Vertical Position, Picture
Adjustment, Fine Picture and Resolution are made automatically. Usually set to ON.
When the Auto mode is turned off with the Mouse pad (-) button is turned off, you can adjust/set Horizon-
tal Position, Vertical Position, Picture Adjustment, Fine Picture and Resolution manually.
Horizontal Position
.. .(when Auto Mode is off)
Use the Mouse pad (+) button to move the image right; (Ð) to move it left. This adjustment is made automati-
cally when the Auto mode is turned on.
Vertical Position
...(when Auto Mode is off)
Use the Mouse pad (+) button to move the image up; (Ð) to move it down. This adjustment is made automati-
cally when the Auto mode is turned on.
Picture Adjustment 
...(when Auto Mode is off)
Use this icon with the ÒFine Picture AdjustmentÓ to fine tune the computer image or to remove any vertical
banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in
the image. Press the Mouse pad (+) and (Ð) buttons until the banding disappears. This adjustment may be
necessary when you connect your computer for the first time. This adjustment is made automatically when the
Auto mode is turned on.
Fine Picture 
...(when Auto Mode is off)
Use this icon to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.) Use the Mouse pad (+) and (Ð) buttons to adjust the
image. Use the Fine Adjustment only after the Picture Adjustment is complete. This adjustment is made auto-
matically when the Auto Mode is turned on.
Resolution
... (when Auto Mode is off)
When Auto mode is selected, the LCD projector automatically determines the best resolution for the current
RGB input signal to project an image using NECs AccuBlend Intelligent Pixel Blending Technology.
Use the Mouse pad (Ð) button to turn off the Auto mode feature to enable the Resolution feature.
Selecting Real allows you to project a source in the real resolution (in the under scan mode) if:
* the LCD projector fails to determine automatically.
* you want to fine adjust an item such as phase.
* you want to project signals other than those with an aspect ratio 4 to 3.
NOTE: Even when you are in the Real mode, an SXGA image is displayed with AccuBlend Intelligent Pixel
Blending Technology.
NOTE:
,The Document Camera mode will not work with an RGB source.
,,Color, Tint, Sharpness and Image Mode controls will not work with an RGB source or PC Card. The
Tint control will not work with a PAL or SECAM source.
,,,Horizontal and Vertical position controls, White Balance, Picture, Fine Picture and Auto Mode
adjustments will not work with a Video, S-Video source or PC card. 
						

							37
Provides access to Lamp Usage information and the Auto Start and Power Management fea-
tures. Use the ÒSelectÓ button on the projector cabinet or (s) (t) buttons on your remote
control to access a submenu. Then press the Mouse pad (+) or (Ð) to choose a specific option.
Lamp Usag e
This tells you how long the lamp has been in operation. It is recommended that you replace a
lamp after 2000 hours of service. After you install a new lamp, select this icon and press and
hold the ÒPower OnÓ button on the remote control for ten seconds to reset the lamp clock back
to zero.
NOTE: The projector will turn off and go into stand by mode after 2100 hours of service. If
this happens, press the Power Off button on the remote control for ten seconds to reset the
lamp clock back to zero. Do this only after replacing the lamp.
Auto Start
Turns the LCD projector on automatically when the main power switch is turned on. This
eliminates the need to always use the ÒPowerÓ button on the remote control or projector
cabinet. Press the Mouse pad (+) to turn this feature on and (Ð) to turn it off.
Power Management
 When ÒPower OffÓ is on and there is no RGB video input for five minutes or more, the
projector will automatically turn itself off. Press the Mouse pad (+) to turn this feature on and
(Ð) to turn it off.  This feature does not work with Video or S-Video sources. Power Menu
OPERATION71
72 Keystone Save
This enables you to save your current keystone settings. Saving your change once affects all
sources.
Use the Mouse pad (+) button to turn the feature on so you save the keystone adjustments;
(-) to turn the feature off so you can cancel them.
On Screen Mute
Use the Mouse pad (+) button to turn off the on screen ; (-) to restore it. The On screen Mute
feature is valid for turning on and switching inputs only. 
						

							38
Settings Menu
Enables you to set preferences and other operating options. Use the ÒSelectÓ button on the projector cabinet or
(s) (t) buttons on your remote control to access the submenu you want.
Capture (with the optional viewer board installed only)
When Capture is selected, press Enter on the projector cabinet or Left Click button on the remote control to
display Execute and capture an image from a source that is currently being displayed. When capturing is
completed, Completed is displayed under the Capture icon.
Unless a flash memory card is inserted into the slot of the viewer board, No Card is displayed. This means that
the Capture feature is not available. The Card Error display means that the free space of the flash memory card
is insufficient for saving images. Make more space available on the card by erasing unwanted images with your
PC. The number of images that can be captured depends on the size of the flash memory card.
NOTE: Be sure not to turn off the power or remove the flash memory card unless Completed is displayed.
Doing so could cause a loss of the data in the flash memory card or damage to the card itself.
Background
Use this feature to display a black or blue screen when no signal is available. Press the Mouse pad (+) or (Ð)
buttons to choose the back screen you want. Press Enter on the cabinet or the Left Click on your remote
control to save your change.
OPERATION73
74 Video Standard
This feature enables you to select composite video standards M_NTSC manually. Normally select Auto.
Use the Mouse pad (+) or (Ð) buttons to choose M_NTSC. Press Enter on the cabinet or the Left Click on
your remote control to save your change.
Projection
This reorients your image for your type of projection.  Press the Mouse pad (+) or (Ð) button until it is correct.
Press ÒENTERÓ on the cabinet or the ÒLeft ClickÓ on your remote control to save your change. The options are:
front floor projection, rear ceiling projection, rear floor projection, and front ceiling projection.
Language
Use the Mouse pad (+) or (Ð) to choose one of six languages for on-screen instructions. Press ÒENTERÓ on the
cabinet or the ÒLeft ClickÓ on your remote control to save your change The options are: English, German,
French, Italian, Spanish and Swedish.
Pointer
This enables you to select from eight different Pointer icons for the Pointer button on your remote control. The
magnifying glass pointer is selected at the factory. Use the Mouse pad (+) or (-) buttons to choose one of the
eight Pointer icons. Press Enter on the cabinet or the Left Click on your remote control to save your change.
After moving your Pointer icon to the area you want on the screen, press the Magnify button on the remote
control to enlarge the selected area on the screen.
Reset
Changes all adjustments to the factory preset levels for each source individually. To activate, you must hold
down the Mouse pad (+) button on the cabinet or remote control for at least two seconds. The adjustments that
will be reset are white balance, horizontal and vertical control, picture and fine picture adjustment (for the
current source only), white balance, brightness, contrast, color, tint, and sharpness. 
						

							39
Using the Viewer function
If you use the Viewer function on the LCD projector, you must first
install the optional MT Viewer board (VK-MT) in the LCD projector
and set up the exclusive software included with the VK-MT kit.
See the users manual included with the VK-MT for installing and
uninstalling the software.
Mounting the Optional MT Viewer Board
To install the Viewer board:
1. Set the LCD projector on end with the carrying handle up.
NOTE: Be sure to unplug the LCD projector before installing the Viewer board.
2. Remove the two screws from the bottom.
3. Remove the slot cover by pushing up on the catch of the cover
with a flat-head screwdriver until you feel it detach.
4. Insert the optional viewer board into the slot. Be sure to push the
board until the board is securely fitted.
5. Secure the board in place with the two screws that you removed in
step 2.6. Put the LCD projector back in the original position.75
76
OPERATION 
						

							40
Projecting Slides
Orientation of flash memory card insertion
The flash memory card has a front and a back side and the flash memory
card is designed to be inserted in only one orientation. The card is
designed so that it cannot be inserted in reverse, but trying to insert it
forcefully might break the pins inside the slot or ruin the flash memory
card slot. See the flash memory card manual for information about the
orientation of the flash memory card.
PCMC IA-ATA
Flash Memory Card
4. Select a file or a slide.
Use the Mouse pad (+) or (Ð) button on the remote control to select
the file or slide you want to display and press the Enter button on
the cabinet or the Left Click button on the remote control. See the
following pages for more details. * The type of flash memory card required for use in the LCD projector
is a Type II PCMCIA-ATA flash memory card (not supplied). Never
use other types of PC card than this. Doing so can break the slot or ruin
the PC card.To Project the Slides (the presentation materials)
1. Insert a flash memory card into the PC card slot.
* To eject the flash memory card, press the Eject button.
NOTE: Should the card be difficult to insert, do not forcefully push
the card in.
2. Select the PC card as a source.
* Press the Menu button on the remote control or projector cabinet
and select PC CARD from the Source menu.
* If there is no flash memory card in the card slot, the LCD projector
displays a blue back or black back image.
3. Select Select File or Select Slide.
* Use the Mouse pad (+) or (-) button on the remote control to select
Select File or Select Slide.
* The selected file or slide will be displayed.
NOTE: If you select Start and press the Enter button on the cabinet
or the Left Click button on the remote control, the slides will be looped.
To use the Start feature, you must first set on the software included
with the MT Viewer board.
8 7
564 3 12
File
File FileFile
File
File FileFile
Multi Cursor
77
78
NOTE: The Mouse pad (+) or (Ð) button is valid only when the Menu
button is lit.
H G
EFD C AB
presentation
presentation presentationpresentation
presentation
presentation presentationpresentation
Table Cursor
OPERATION