NEC Mt830 Lcd Projector Users Manual

21INSTALLATION40
     WARNING
¥Only use your LCD projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector
severely damaged.
¥ Do not use the LCD projector where temperatures vary greatly. The projector must be used at temperatures between 32ûF
(0ûC) and 104ûF (40ûC).
¥
Do not expose the LCD projector to moisture, dust, or smoke. This will harm the screen image.
¥Ensure that you have adequate ventilation around your LCD projector so heat can...

22
41
42
Standard Zoom Lens (Wide)
Standard Zoom Lens (Tele)
INSTALLATION
a
b (sin= a)
g (cos= a)
Screen Size
HÐWidth
4 : 3 Diagonal
A
B
C
F
C/H-Width
magnificationDegree
inch
inch
mm
inch
mm
inch
mm
inch
mm
inch9.02
0.15671
0.98764
32
40
1572
61.9
332
13.1
1552
61.11
-27
-1.0
1.91
30.798.86
0.15395
0.98808
48
60
2400
94.5
455
17.9
2371
93.36
3
0.1
1.94
46.188.81
0.15318
0.98820
56
70
2814
110.8
516
20.3
2781
109.48
17
0.7
1.95
53.888.78
0.15260
0.98829
64
80
3228
127.1
578
22.7
3190
125.60
32
1.3
1.96...

23
PC CONTROLMOUSE OUTPUTREMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2AUDIO RGB   INPUT   1AUDIO
RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONOINPUT    AUDIO VIDEO
If your projector is mounted on the ceiling and your image is upside down, use
the ÒMenuÓ and ÒSelectÓ buttons on your projector cabinet or (s) (t)  buttons
on your remote control to correct the orientation. (See page 70.)
Reflecting The Image
Using a mirror to reflect your LCD projectors image enables you to enjoy a
much larger...

24
PC CONTROL MOUSE OUTPUTREMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
Wiring Diagram
Remote Control Guideline
1. Plug the serial cable with the mouse output port of the projector into your computers mouse port and restart your computer to gain remote
mouse control.
2. When using the remote controls built-in infrared mouse on a laptop computer, the laptops mouse, trackball or trackpad will be...

25
Connecting Your PC Or Macintosh
Computer
Connecting your PC or Macintosh computer to your MultiSync
MT830 (SVGA) /1030 (XGA) Projector will enable you to project
your computers screen image for an impressive presentation. All of
these following display standards are supported:
To connect to a PC, Macintosh or computer equipped with an XGA/
SVGA /VGA adapter or compatible graphics adapter, simply:
1. Turn off the power to your projector and computer.
2. If your PC does not support XGA/SVGA/VGA you will...

26
Settings for Macintosh Adapter
Macintosh models applied
Desktop type and PowerBook with
8002600 LCD panel
PowerBook with 6402480 LCD panel
Desktop type with AccuBlendSetting required to be selected resolution
on Mac after restarting.
Set to VGA/SVGA (8002600)
Set to 17Ó multi-scan mode (6402480)
Set to 17Ó multi-scan mode (10242768) Setting Mode (Fixed resolution)
16Ó fixed mode (output is 8322624)
13Ó fixed mode (output is 6402480)
19Ó fixed mode (output is 10242768)
NOTE: Refer to your computers...

27
Changing Video Resolutions
Depending on your computers graphic capability, you may be able
to select one of several resolutions. Generally a computer- either a
PC or Macintosh- with 1 meg. of memory will run:
6402480 at 16.7 million colors (24 bit Truecolor)
8002600 at 65 thousand colors.
10242768 at 256 colors.
As the resolution increases,  the number of colors you can run
decreases.  With 2 meg. of memory a computer will run:
6402480 at 16.7 million colors (24 bit Truecolor).
8002600 at 16.7 million...

28
Connecting Your Document Camera
You can connect your MultiSync MT830/1030 LCD Projector to a document camera. To do so, simply:
1. Turn off the power to your LCD projector and document camera.
2. Use a standard video cable to connect your document camera to the Video input on your projector.
3. Turn on the LCD projector and the document camera.
NOTE: Refer to your document cameras owners manual for more information about your cameras video
output requirements .
Connecting Your VCR Or Laser Disc...

29
REMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
REMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
Connecting Your Computer to the
Mouse Output Port
The built-in remote mouse receiver enables you to operate your
computers mouse functions from the NEC MultiSync MT830/1030
remote control. It is a...

30
This section describes how to select a computer or video source and how to adjust
the picture and sound.
General Controls Before you turn on your MultiSync MT830/1030 LCD Projec-
tor,  ensure that the computer or video source is turned on and that your lens cap is
removed.
1.Turn On The LCD Projector The main power switch is on the front panel of
the MultiSync MT830/1030 LCD Projector. By turning this switch on, the
projector will go into its standby mode and the power light will glow amber.
Only...