NEC Mt820 Projector Users Manual

FOCUS
ZOOM
ADJUST
ENTER
SELECT
MENU
POWER
ON/OFFSTATUS PUSH
Top Features
1Power Button
Use this button to turn the power on and off when the Main Power Switch is on and
the LCD projector is in standby. (When this button is pressed and held for at least
two seconds, the ÒDisplay MuteÓ mode will be canceled.)
2Menu Button
Displays the on- screen menu.
3Select Button
After you press the ÒMenuÓ button, use this button to select the menu icon of the
item you wish to adjust.
4Enter Button
Executes your menu...

Terminal Panel Features
This panel is located in the rear and is where you connect your cables.
1Remote Control Jacks
a. Remote Control Input Jack
Connect your remote control cable here for wired operation.
b. Remote Control Output Jack
This terminal enables you to operate up to five LCD projectors with
the same remote control.
When your remote mouse receiver is connected here, the remote
sensors on the LCD projector cabinet will receive your mouse
commands.
2PC Control Port
Use this port to connect your...

6RGB Input 1 Connector (D-Sub 15 pin)
Connect your PC or other RGB equipment such as IBM or compat-
ible computers. Use the NEC MultiCable thats supplied to connect
to a PC.
RGB 1 Audio Input Mini Jack
This is where you connect RGB audio output from a computer or
another RGB source.
7RGB Input 2 Connector (Mini D-Sub 15 pin)
Connect a Macintosh or compatible computer here using the NEC
MultiCable thats supplied.
RGB 2 Audio Input Mini Jack
This is where you connect a second RGB audio output from a...

Remote Control Features
You can use your remote control with the cable or wireless to operate your
MultiSync MT1020/MT820 LCD Projector. With the remote mouse receiver
connected to your computer, you can also use the projectors remote control to
operate your computers mouse wireless, too. (See pages 43 and 44 to connect
the remote mouse receiver to your computer.)
If you want to use your remote control with the cable, connect one end of the
cable to the jack on the remote control and the other end to the...

NOTE: You cannot use Menu and Position at the same time.
Remote Control Precautions
¥ Do not look into the laser pointer while it is on.
¥ Do not point the laser beam at a person.
¥ When the cable is connected to the remote control, it will not work in the
wireless mode.
¥ Handle the remote control carefully.
¥ If the remote control gets wet, wipe it dry immediately.
¥ Avoid excessive heat and humidity.
¥
If you will not be using the remote control for a long time, remove the batteries.¥ Do not mix new...

This section describes how to set up your MultiSync MT1020/MT820 LCD
projector and how to connect video and audio sources.
Setting Up Your MultiSync MT1020/MT820
LCD Projector
Your MultiSync MT1020/MT820 LCD Projector is simple to set up and use.
But before you get started, you must first:
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can project
your image.
Carrying The LCD Projector Always carry your LCD projector by the
handle. Ensure that the power...

Using A Tabletop Or Cart
1. Place your LCD projector on a flat level surface at the optimal
distance from the screen or wall so you realize the size image you
want. (Avoid having bright room lighting or sun light directly on the
screen or wall where youll be projecting the image.)
2. Connect the power cable, remove the lens cap and turn the projector
on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
4. Move the...

If your projector is mounted on the ceiling and your image is upside down, use the
ÒMenuÓ and ÒSelectÓ buttons on your projector cabinet or (s) (t)  buttons on your
remote control to correct the orientation. (See page 60.)
Reflecting The Image
Using a mirror to reflect your LCD projectors image enables you to enjoy a much
larger image. Contact your NEC dealer if you need a mirror.
If youre using a mirror and your image is inverted, use the ÒMenuÓ and ÒSelectÓ
buttons on your projector cabinet or (s) (t)...

REMOTE CONTROLPC
CONTROL
S-VIDEO INPUTINPUT
VIDEO INPUT AUDIO INPUTOUTPUT
AUDIO OUTPUT
AUDIO RGB INPUT 1
RGB INPUT 2
AUDIODC12V/400mA
OUTPUT
RGB MONITOR OUTPUT
L / MONO

R
L / MONO

R
      

 
 


Document Camera
VCR or LaserDisk Player
IBM VGA or Compatibles Macintosh or Compatibles
Remote Mouse Receiver Remote Mouse Receiver
IBM/MAC MultiCable
To mini D-Sub 15-pin or D-Sub 15-pin
connector on the LCD Projector.
Wiring Diagram
To video, S-video,
and audio inputs on
the LCD projector.
PS/2 mouse...

3. Use the MultiCable thats supplied to connect your PC or Macintosh computer to the
LCD projector. For a PC, use the smaller 15-pin connector on the cable to connect to
your computers video port; use the larger 15-pin connector on the cable to connect
to the projectors RGB 1 input. For Macintosh, use the larger 15-pin connector on the
cable to connect to your computers video port; use the smaller 15-pin connector on
the cable to connect to the projectors RGB 2 input. (You can also use your own
video...