NEC Mt1060 Lcd Projector Users Manual

							E-7
11 10 9 8
4
14 12 13256
17
3
Top Features
1. POWER Button (ON / STAND BY)(  )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
NOTE: To turn on or off the projector, press and hold this button for a mini-mum of two seconds.
2. POWER Indicator
When this indicator is green, the projector is on; when this indicator
is orange, it is in standby or idle mode. See the Power Indicator sec-
tion on page E-55 for more details.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred,
the lamp cover is not attached properly or the projector has over-
heated. If this light remains orange, it indicates that you have pressed
a cabinet key while the Control Panel Key Lock is enabled. See the
Status Indicator section on page E-55 for more details.
4. LAMP Indicator
If this light blinks red rapidly, its warning you that the lamp has reached
the end of its usable life. After this light appears, replace the lamp as
soon as possible (See page E-53). If this is lit green continually, it
indicates that the lamp mode is set to Eco. See the Lamp Indicator
section on page E-55 for more details.
5. SOURCE Button
Use this button to select a video source such as a PC, VCR, DVD
player, Viewer (PC card), or LAN.
Press and release this button quickly to display the Source List.
Each time this button is pressed for a minimum of ONE second, the
input source will change as follows:
RGB1 → RGB2 → Video → S-Video → DVI (DIGITAL)* → Viewer → RGB1 → ...
If no input signal is present, the input will be skipped.
6. AUTO ADJUST Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture (See page E-22). Also press and hold this button for a
minimum of 2 seconds to enable the Auto Focus* or Auto Wall Color
Correction* function (See page E-47).
7. 3D REFORM Button
Press this button to enter 3D Reform mode to correct the keystone
(trapezoidal) distortion, and make the image square.
8. ZOOM Button (+/-)
Zoom the lens in and out.
9. FOCUS Button (+/-)
Adjust the lens focus.
10. MENU Button
Displays the menu.11. SELECT 
 (+) (–) / Volume Buttons

 : Use these buttons to select the menu of the item you wish to
adjust. When no menus appear, these buttons work as a vol-
ume control.
  : Use these buttons to change the level of a selected menu item.
A press of the  button executes the selection. When the menus
or the Viewer tool bar is not displayed, these buttons can be
used to select a slide, or to move the cursor in Folder List or
Slide List.
When the pointer is displayed, these 
 buttons move the pointer.
12. ENTER Button
Executes your menu selection and activates items selected from the
menu.
13. CANCEL Button
Press this button to exit Menus. Press this button to return the ad-
justments to the last condition while you are in the adjustment or
setting menu.
14. PC CARD Access Indicator 1/2
Lights while accessing a PC card.
NOTE: The functions flagged with an asterisk (*) are not available on MT860. 
						

							E-8
1. RGB1 IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player. This connector also
supports SCART output signal. See page E-15 for more details.
RGB1 AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer or
DVD player when connected to the RGB1 input. A commercially avail-
able audio cable is required.
2. RGB2 IN / Component Input Connectors (BNC)
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of
external equipment.
If using a component with a combined sync (SYNC) output, connect
it to the H/V terminal.
When using luminance and color-difference signals of HDTV and DVD,
connect Pr/Cr to the R,Y to the G and Pb/Cb to the B input of the
projector.
NOTE: The RGB IN 2 does not support Plug & Play.
RGB2 AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your computer or DVD
player connected to the RGB2 input. A commercially available audio
cable is required.
3. DVI IN Connector (24 pin)
NOTE: The DVI connector is not available on MT860.
This connector can be used to accept a digital signal output from a
computer or other sources with a DVI connector.
DVI AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer when
connected to the DVI input. A commercially available audio cable is
required. On MT860 this AUDIO input mini jack is used for Viewer
and LAN exclusively.
4. RGB OUT Connector (Mini D-Sub 15 Pin)
You can use this connector to loop your computer image to an exter-
nal monitor from the RGB 1 or 2 input source.
The RGB analog signal set on RGBOUT Terminal is output during
idle mode. See pages E-15 and 45.
RGB AUDIO OUT Mini Jack (Stereo Mini)
Connect an additional audio equipment here to listen to audio com-
ing from your computer connected to RGB1, RGB2 or DVI input (not
available on MT860).
Note that there is no audio output from this jack during Standby and
Idle.
Terminal Panel Features
8 9 10 13 12
3
2
1
56 4711
5. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external source
like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than the tra-ditional composite video format.
S-VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound
from an S-Video source.
6. VIDEO IN Connector (RCA)
Connect a VCR, DVD player, laser disc player, or document camera
here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound
from a Video source.
7. AUDIO OUT Jacks R/L (RCA)
You can use this connector to output sound from the currently se-
lected input source (RGB 1, RGB 2, DVI (DIGITAL) (not available on
MT860), Video or S-Video).
Output sound level can be adjusted in accordance with the sound
level of the internal speaker.
8. USB Port (MOUSE/HUB) [Type A]
Connect the supplied USB mouse. You can operate the menu or Viewer
with the USB mouse via this port.
• A USB-supported scanner or PC peripheral can be connected
to this port. (USB Hub Function)
9. USB Port (PC) [Type B]
Connect this port to the USB port (type A) of your PC using the sup-
plied USB cable. You can operate your computers mouse functions
from the remote control. This port also serves as a PC Control port
by using Dynamic Image Utility 2.0 included on the supplied CD-
ROM.
10. REMOTE (Mini Jack)
Connect your remote control cable here for wired operation.
11. PC CONTROL Port (D-Sub 9 Pin)
Use this port to connect your PC to control your projector via a serial
cable. This enables you to use your PC and serial communication
protocol to control the projector. A commercially available RS232C
cross cable is required to use this port. You can also control the pro-
jector by using Dynamic Image Utility 2.0 included on the supplied
CD-ROM.
To do so you must first have Dynamic Image Utility 2.0 installed on
your PC. If you are writing your own program, typical PC control codes
are on page E-60.
12. PC CARD Slot 1/2
Insert a PC card, commercially available LAN card or NEC optional
wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
NOTE: A dummy card is inserted into each slot at the time of shipment. Firstremove the dummy cards before use.
13. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject button:
1 and 2. 
						

							E-9
Part Names of the Remote Control
NOTE: If you are using a Macintosh computer, you can click either the right-clickor left-click button to activate the mouse.
NOTE: The functions flagged with an asterisk (*) are not available on MT860.
PJFREEZE3D REFORMPIC-MUTEE
OFF
VIDEO
AUTO ADJ.RGB
VIEWE
R
LASERONPOW
ER
SELECT
21
3
1. Infrared Transmitter
Direct the remote control toward
the remote sensor on the projec-
tor cabinet.
2. LASER Pointer
Beams a laser light when the LA-
SER button is pressed.
3. Remote Jack
Connect your remote control
cable here for wired operation.
MENU
PJ
ASPECT OFF
VIDEO
AUTO ADJ.
RGB VIEWER
LASERON
3D REFORM
HELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTE
SLIDE
FOLDER
SLIDE
LIST
ENTERCANCEL
POWER
SELECT
FREEZE
FOCUS
16
21
19
22
27
28
29 17
20
23
25
26 2415 14 1211 109 78 5 64
18
13
9. VIEWER Button
Press this button to select the Viewer source.
10. AUTO ADJ Button
Use this button to adjust an RGB source for an optimal picture. Also
press and hold this button for a minimum of 2 seconds to enable the
Auto Focus* or Auto Wall Color Correction* function. See page E-20
or 22.
11. LASER Button
Press and hold this button to activate the laser pointer. When lit, you
can use the laser to draw your audiences attention to a red dot that
you can place on any object.
12. MENU Button
Displays the menu for various settings and adjustments.
13. SELECT 
 (Mouse) Button
When you are in the Computer mode, these buttons work as a com-
puter mouse.
When you are in the Projector mode, which is indicated by lighting
the PJ button. See page E-24.

 : Use these buttons to select the menu of the item you wish
to adjust.
 : Use these buttons to change the level of a selected menu
item. A press of the  button executes the selection.
When the pointer is displayed, these 
 buttons move the pointer.
When the pointer is not displayed, these 
 buttons are for adjust-
ing the image.
14. ENTER (Left Click) Button
When you are in the Computer mode, this button works as the mouse
left button. When this button is pressed and held for a minimum of 2
seconds, the drag mode is set. When you are in the Projector mode,
which is indicated by lighting the PJ button: Use this button to enter
your menu selection. It works the same way as the ENTER button on
the cabinet. See page E-7.
15. CANCEL (Right Click) Button
When you are in the Computer mode, this button works as the mouse
right button. When you are in the Projector mode, which is indicated
by lighting the PJ button: Press this button to exit the Menus. It works
the same way as the CANCEL button on the cabinet. See page E-7.
16. PJ Button
Press this button to switch the SELECT, CANCEL, and ENTER but-
tons between the Projector mode (lit red) and the Computer mode.
Press this button or any one of the POWER ON/OFF, MENU, AS-
PECT, 3D REFORM, HELP, POINTER, MAGNIFY, VIEWER, FOLDER
LIST or SLIDE LIST buttons to switch to the Projector mode and the
PJ button lights red. To switch back to the Computer mode, press the
PJ button again. See page E-24.
17. ASPECT Button
Press this button to display the Aspect Ratio select screen. See page
E-38.
18. FREEZE Button
This button will freeze a picture. Press again to resume motion.
19. 3D REFORM Button
Press this button to enter 3D Reform to correct the keystone (trap-
ezoidal) distortion, and make the image square. See page E-20.
20. HELP Button
Provides the online help or the set information.
21. POINTER Button
Press this button to display one of the eight pointers; press again to
hide the pointer. You can move your pointer icon to the area you want
on the screen using the Select 
 button. See page E-25. 4. LED
Flashes when any button is pressed.
5. POWER ON Button
When the main power is on, you can use this button to turn your
projector on.
NOTE: To turn on the projector, press and hold the POWER ON button for aminimum of two seconds.
6. POWER OFF Button
You can use this button to turn your projector off.
NOTE: To turn off the projector, press and hold the POWER OFF button for aminimum of two seconds.
7. VIDEO  Button
Press this button to toggle between Video and S-Video inputs.
8. RGB Button
Press this button to select RGB 1, RGB 2 or DVI (DIGITAL)* inputs.
Each time this button is pressed, the input source will change as
follows:
RGB 1 → RGB 2 → DVI (DIGITAL)* → RGB 1 → ... 
						

							E-10
MENU
PJ
ASPECT OFF
VIDEO
AUTO ADJ.
RGB VIEWER
LASERON
3D REFORM
HELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTE
SLIDE
FOLDER
SLIDE
LIST
ENTERCANCEL
POWER
SELECT
FREEZE
FOCUS
16
21
19
22
27
28
29 17
20
23
25
26 2415 14 1211 109 78 5 64
18
13
22. PICTURE MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an imageand sound without turning off the menu.
23. VOLUME (+)(–) Button
Press (+) to increase the volume and (–) to decrease it.
24. MAGNIFY (+)(–) Button
Use this button to adjust the image size up to 400%. When the pointer
is displayed, the image is magnified about the center of the pointer.
When the image is magnified, the pointer is changed to the magnify-
ing icon.
When the pointer is not displayed, the image is magnified about the
center of the screen. See page E-25.
25. ZOOM (+)(–) Button
Zoom the lens in and out.
26. FOCUS (+)(–) Button
Adjust the lens focus.
27. SLIDE (+)(–) Button
Press (+) to select the next folder or slide and (–) to select the previ-
ous folder or slide. See page E-29.
28. FOLDER LIST Button
Press this button to select Viewer source to display a list of folders
included in a PC card. See page E-29.
29. SLIDE LIST Button
Press this button to select Viewer source to display a list of slides
included in a PC card. See page E-29.
NOTE: The default is the Computer mode, which allows you to use the SELECT,
CANCEL, and ENTER buttons as your computer mouse. When the POWER ON/
OFF, MENU, ASPECT, 3D REFORM, HELP, POINTER, MAGNIFY, VIEWER, FOLDER
LIST, or SLIDE LIST button is pressed, the PJ button lights red to indicate that
you are in the Projector mode. If no buttons are pressed within 60 seconds, the
light goes out and the Projector mode is canceled. 
						

							E-11
Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not
mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT 
 button while installing new
batteries, the remote control may fail to work properly.
Should this happen, remove the batteries and then install them again
without touching the SELECT button.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the
batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of
batteries together
Operating Range for Wireless Remote Control
7m/22 feet7m/22 feet
Remote control Remote sensor on the
projector cabinet
• The infrared signal operates by line-of-sight up to a distance of about
22 feet/7 m and within a 60-degree angle of the remote sensor on the
projector cabinet.
• The projector will not respond if there are objects between the re-
mote control and the sensor, or if strong light falls on the sensor.
Weak batteries will also prevent the remote control from properly
operating the projector.
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE mini
jack and the other end to the remote jack on the remote control.
Remote sensor on the
projector cabinet
REMOTE
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDEFOLDER
SLIDELIST
POWER
FREEZEFOCUS 
						

							E-12
3
1
2
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
To the wall outlet.
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25 (0.64 m)
measured diagonally when the projector is roughly 39.4 inches (1.0 m) from the wall or screen. The largest the image can be is 500 (12.7 m) when
the projector is about 614.2 inches (15.6 m) from the wall or screen. Use the drawing below as a guide.Your projector is simple to set up and use.
But before you get started, you must first:
z
Set up a screen and the projector.
xConnect your computer or video equip-
ment to the projector. See page
E-14–17.
cConnect the supplied power cable. See
page E-17.
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
300
240
406.4(W)X304.8(H)/160(W)X120(H)
365.8(W)X274.3(H)/144(W)X108(H)
304.8(W)X228.6(H)/120(W)X90(H)
243.8(W)X182.9(H)/96(W)X72(H)
203.2(W)X152.4(H)/80(W)X60(H)
162.6(W)X121.9(H)/64(W)X48(H)
121.9(W)X91.4(H)/48(W)X36(H)
81.3(W)X61.0(H)/32(W)X24(H)
61.0(W)X45.7(H)/24(W)X18(H)
TELE: 50.8(W)X38.1(H)/20(W)X15(H)
Lens center
Screen Size
1.42.1
2.8
3.5
4.3
5.3
6.4
8.51.11.0
200
180
150
120
100
80
60
40
3025
609.6(W)X457.2(H)/240(W)X180(H)Screen size (Unit: cm/inch)
487.7(W)X365.8(H)/192(W)X144(H)
7.1
Distance (Unit: m)
10.6
WARNING:To avoid premature lamp failure, do not tilt the front of the
projector up or down by more than 15° from level. 
						

							E-13
NOTE: Distances may vary +/-5%.
Reflecting the Image
Using a mirror to reflect your projectors image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
youre using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or 
 buttons on your re-
mote control to correct the orientation. (See page E-44.) WARNING
* Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
• To avoid premature lamp failure, do not tilt the front of the projector
up or down by more than 15° from level.
• Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector severely dam-
aged.
• Do not use the projector where temperatures vary greatly. The pro-
jector must be used at temperatures between 32˚F (0˚C) and 95˚F
(35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will
harm the screen image.
• Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the side or the front of
the projector. Distance Chart
B = Ver tical distance between lens center and screen center
C = Throw distance
α = Throw angle
Lens Center
Throw Angle (
)
Throw Distance (C) Screen center Screen Diagonal Screen Width
Screen Height
Screen Bottom
(B)
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
α
Wide – Tele
inch
15
18
24
36
40
43
48
50
54
60
72
90
108
120
126
144
157
162
180
210
240
270
300 Screen Size B C
Wide – TeleDiagonal Width Heightinch
––– - 39.6
35.1 - 47.8
47.4 - 64.4
72.1 - 97.6
80.7 - 109.2
86.9 - 117.5
96.8 - 130.8
101.7 - 137.4
109.1 - 147.4
121.4 - 164.0
146.1 - 197.2
183.1 - 246.9
220.1 - 296.7
244.8 - 329.9
257.1 - 346.5
294.1 - 396.3
320.0 - 431.1
331.1 - 446.0
368.1 - 495.8
429.8 - 578.7
491.5 - –––
553.2 - –––
614.8 - –––degree
––– - 10.7
14.4 - 10.7
14.2 - 10.5
14.0 - 10.4
14.0 - 10.4
14.0 - 10.4
13.9 - 10.4
13.9 - 10.4
13.9 - 10.4
13.9 - 10.4
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.7 - 10.3
13.7 - 10.3
13.7 - 10.3
13.7 - 10.3
13.7 - –––
13.7 - –––
13.7 - ––– inch
8.0
9.0
12.0
18.0
20.0
22.0
24.0
25.0
27.0
30.0
36.0
45.0
54.0
60.0
63.0
72.0
78.0
81.0
90.0
105.0
120.0
135.0
150.0
α
Wide – Tele
mm
381
457
610
914
1021
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
3978
4115
4572
5334
6096
6858
7620 Screen Size B C
Wide – Tele
Diagonal Width Heightmm
––– - 1005
891 - 1215
1204 - 1636
1831 - 2479
2050 - 2774
2207 - 2985
2458 - 3322
2583 - 3490
2771 - 3743
3084 - 4165
3711 - 5007
4651 - 6272
5591 - 7536
6217 - 8379
6531 - 8800
7471 - 10064
8129 - 10949
8410 - 11328
9350 - 12593
10917 - 14700
12484 - –––
14050 - –––
15617 - –––degree
––– - 10.7
14.4 - 10.7
14.2 - 10.5
14.0 - 10.4
14.0 - 10.4
14.0 - 10.4
13.9 - 10.4
13.9 - 10.4
13.9 - 10.4
13.9 - 10.4
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.8 - 10.3
13.7 - 10.3
13.7 - 10.3
13.7 - 10.3
13.7 - 10.3
13.7 - –––
13.7 - –––
13.7 - ––– mm
191
229
305
457
511
549
610
640
686
762
914
1143
1372
1524
1600
1829
1989
2057
2286
2667
3048
3429
3810 mm
635
762
1016
1524
1702
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6629
6858
7620
8890
10160
11430
12700mm
508
610
813
1219
1361
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5304
5486
6096
7112
8128
9144
10160 inch
25
30
40
60
67
72
80
84
90
100
120
150
180
200
210
240
261
270
300
350
400
450
500inch
20
24
32
48
54
58
64
67
72
80
96
120
144
160
168
192
209
216
240
280
320
360
400 
						

							E-14
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computers screen-saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.
When Viewing a DVI Digital Signal*:
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC or
projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC.
Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected and then re-connected, an image
may not be correctly displayed. Should this happen, restart your PC.
NOTE: The DVI connector is not available on MT860.
NOTE:
• Use the DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should be within
5 m (196) long.
• The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).
PHONE
PHONE
DVI IN
RGB 2 IN
RGB 1 IN
Connecting Your PC or Macintosh Computer
Audio cable (not supplied)
IBM VGA or Compatibles (Notebook type)
or Macintosh (Notebook type)IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type) RGB signal cable (supplied)
To mini D-Sub 15-pin connec-
tor on the projector. It is recom-
mended that you use a com-
mercially available distribution
amplifier if connecting a signal
cable longer than the supplied
one.
NOTE: For older Macintosh,
use a commercially available
pin adapter (not supplied) to
connect to your Macs video
port.
Connecting your PC or Macintosh computer to your projector will en-
able you to project your computers screen image for an impressive pre-
sentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the
projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer youve connected to the
projector.
Connecting to RGB 2 IN connectors
Use a BNC
5 cable to connect your PC and the RGB 2 IN connectors
on your projector.
Connecting Your PC with a DVI Connector*
Use a DVI-D signal cable (not supplied) to connect a DVI connector of
your PC to the projector.
NOTE: The MT1065/MT1060/MT860 is not compatible with video decoded out-puts of NEC ISS-6020 and ISS-6010.
DVI-D cable (not supplied) 
						

							E-15
To connect SCART output (RGB)
Before connections: An exclusive SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE:
• Audio signal is not available for this connection.
• The RGB IN 2 connector does not support Plug & Play.
RGB 1 IN
Video equipment
such as DVD playerProjector
ADP-SC1Commercially available
SCART cableFemale
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially avail-
able SCART cable to connect the RGB 1 input of your projector and
a SCART output (RGB) of your video equipment.
3. Turn on the power to the projector and your video equipment.
4. Use the RGB 1 button on the remote control to select the RGB 1
input.
5. Press the MENU button on the remote control to display the menu.
6. From the Advanced menu, select [Projector Options] 
→ [Setup] →[Page 3] → [Signal Select RGB1] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs
and DVD players. It is also referred to as Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Eu-rope. Contact your NEC dealer in Europe for more information.
To RGB IN 1
Connecting an External Monitor
You can connect a separate, external monitor to your projector to simul-
taneously view on a monitor the RGB analog image youre projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the RGB OUT (Mini D-
Sub 15 pin) connector on your projector.
3. Turn on the projector, monitor and the computer.
NOTE:
• The RGB OUT connector outputs RGB signal during idle mode (See page E-
45). When the projector goes into idle mode, the image on an external moni-
tor disappears for a moment. Note that the RGB OUT connector will not out-
put RGB signal during Standby mode.
• When the projector is in the Idle mode, the image may not be correctly dis-
played while the cooling fans are running immediately after turning on or off
the power. Note that the RGB OUT connector will not output RGB signal dur-
ing Standby mode.
• Daisy chain connection is not possible.
RGB OUT
LINE IN
PHONE 
						

							E-16
AUDIO OUTL
AUDIO INLRRComponentYCbCr
RGB 1 IN
RGB 2 IN
Connecting Your DVD Player
DVD player
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a
commercially available component video cable (RCAX3) and the op-
tional 15-pin-to-RCA (female)

3 cable to connect your DVD player
to the RGB IN1 or IN2 connector on the projector. Component video RCA

3 cable
(not supplied)
For a DVD player without component video (Y,Cb,Cr) output, use com-
mon RCA cables (not provided) to connect a composite VIDEO out-
put of the DVD player to the Video Input of the projector.
3. Turn on the projector and DVD player.
NOTE: Refer to your DVD players owners manual for more information aboutyour DVD players video output requirements, Optional 15-pin-to-RCA
(female)

3 cable (ADP-CV1)
Audio cable
(not supplied)Audio Equipment
RCA(female)-to-BNC(male)
adapter (not supplied)