NEC Mt1045 Projector Users Manual

LCD Projector
MultiSync MT840/MT1040/MT1045
UserÕs Manual 

EÐ2
IMPORTANT INFORMATION
Precautions
Please read this manual carefully before using your NEC
MultiSync MT840/MT1040/MT1045 Projector and keep
the manual handy for future reference.
Your serial number is located under the name plate label
on the left side of your MultiSync MT840/MT1040/
MT1045. Record it here:
CAUTION
To turn off main power, be sure to remove the
plug from power outlet.
The power outlet socket should be installed
as near to the equipment as possible, and
should be easily accessible....

EÐ3
Important Safeguards
These safety instructions are to ensure the long life of
your projector and to prevent fire and shock. Please read
them carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away
from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters
or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm in-
ternal...

EÐ4
Lamp Replacement
¥ To replace the lamp, follow all instructions provided on page
E-33.
¥ Be sure to replace the lamp when the Status light comes
on. If you continue to use the lamp after 2000 hours (1500
hours : MT1045) of use, the lamp bulb may shatter, and
pieces of glass may be scattered in the lamp case. Do not
touch them as the pieces of glass may cause injury. If this
happens, contact your NEC dealer for lamp replacement.
¥ Allow a minimum of ONE minute to elapse after turning off
the...

EÐ5
TABLE OF CONTENTS
1. INTRODUCTION
Introduction to the MultiSync MT840/MT1040/MT1045 Projector... E-6
Getting Started ............................................................ E-6
Getting to Know Your MultiSync MT840/MT1040/MT1045 Projector..... E-7
Front Features ......................................................... E-7
Rear Features ......................................................... E-7
Top Features ........................................................... E-8
Terminal Panel Features...

EÐ6
1. INTRODUCTION
Introduction to the MultiSync MT840/MT1040/MT1045 Projector
This section introduces you to your new MultiSync MT840 (SVGA)/
MT1040 and MT1045 (XGA) Projector describes the features and
controls.
Congratulations on Your Purchase of The MultiSync MT840/
MT1040/MT1045 Projector
The MultiSync MT840/MT1040/MT1045 is one of the very best pro-
jectors available today. The MultiSync MT840/MT1040/MT1045 en-
ables you to project precise images up to 300 inches across (mea-
sured diagonally)...

EÐ7
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFF
SOURCE AUTO  ADJUSTUSB
AC IN
Getting to Know Your MultiSync MT840/MT1040/MT1045 Projector
Front Features
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFF
SOURCE AUTO  ADJUST
Remote Sensor
One-Touch Tilt Button
Rear Features
Controls
USB (Mouse) Terminal
FocusLens
Adjustable Tilt Foot
AC Input
Cannot the supplied power
cableÕs three-pin plug here.
Air-Filter
Remote Sensor
Zoom
Slot for Kensington
MicroSaver Security System
Air-Filter
Terminal Panel
Carrying Handle...

EÐ8
Top Features
1 Source Button
Use this button to select a video source such as a PC, VCR, DVD
player or PC Card Viewer (PC card installed).
2 Auto Adjust Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for
an optimal picture. Some signals may not be displayed correctly or
take time to switch to another.
3 Menu Button
Displays the main menu for operation.
4 Select (st
§ ©) / (+) (Ð) Buttons
st: Use these buttons to select the menu of the item you wish
to adjust.
§ ©: Use these...

EÐ9
USB
PC CONTROLREMOTE
CONTROL
INPUT MOUSE
OUT
S-VIDEO
VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1
L/MONO
R
Terminal Panel Features
1
86 5
10 1211
1 USB (Mouse) Terminal
Connect a commercially available mouse that supports USB.
You can operate the menu or Viewer with the USB mouse via this
terminal.
Note that this terminal is not used with a computer and that there
may be some brands of USB mouse.
2 PC Card Access Slot
Insert a PC card here.
3 PC Card Access Indicator
Lights while accessing a PC card.
4...

EÐ10
Remote Control Features
NOTE: If you are using a Macintosh computer, you can click either
the right or left button to activate the mouse.
1 Source Button
Press to select a video source.
2 Auto Adjust Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for
an optimal picture. Some signals may not be displayed correctly,
or in some cases it may take some time for a source to be switched
to another.
3 Menu Button
Displays the main menu for operation.
4 Mouse (st
§ ©) /  (+) (Ð) Buttons...