NEC Mt1045 Lcd Projector Users Manual

							EÐ31
Uninstalling the PC Card Viewer Software
Even if you do now know the PC Card Viewer softwares file names
or where they are stored, the PC Card Viewer software files can be
easily removed from the system using the Install/Uninstall Applica-
tions control panel in Windows 95.  (Normally there is no need to
perform this operation.)
Uninstalling the software
Use the procedure described below to uninstall the PC Card Viewer
software files.
1. From the Start menu, select Settings then Control Panels.
2. In the Control Panels dialog box, double-click on Add/Remove
Programs.
3. In the Add/Remove Programs Properties dialog box, click the
Setup/Remove tab, then select PC Card Viewer Utility 1.0 from
the list of applications and click on Add/Remove.
4. In the Confirm File Deletion dialog box, click Yes.
5. Once the application is uninstalled, click on OK in the Re-
move Program From Your Computer dialog box.
Deleting Captured Images
Using the Delete button on the tool bar for PC Card Viewer can de-
lete captured images.
To delete captured images:
1) Select PC Card Viewer.
2) Use © button to select the Capture folder in the right bottom of
the screen.
3) Press the MENU button to display the tool bar.
4) Use the § or © button to select the Delete icon and press the
ENTER button or  click with a mouse button.
Viewing Digital Images
Digital images can be played with the PC Card Viewer if the follow-
ing conditions are met:
¥ If the image can be stored on an MS-DOS format PC card
¥ If the image can be stored in a format supported by the PC Card
Viewer.
With the PC Card Viewer, images on the card are searched for in
directories and images in JPEG or BMP format are recognized
as slides.
Searchable directories are directories within two steps from the
root directory, and searchable images are images within the first
12 files in the directory.  Only file and slide switching are pos-
sible.
NOTE: The maximum number of images recognized as slides within
one directory is 128.
Drag
Prev
Next
Play/Stop
Jump
Select
DeleteView 
						

							EÐ32
This is the name of a card currently being standardized by the Japan Electronic Industry Association (JEIDA) and
PCMCIA (Personal Computer Memory Card Interface Association) of the United States.
PCMCIA 2.1 PC cards are divided into three types according to their thickness:  Type I (3.3 mm), Type II (5.0 mm)
and Type III (10.5 mm).
A type of image format.  The standard Windows Bit Map format used for MS-DOS/Windows-compatible comput-
ers.
A type of image format.  JPEG is the abbreviation of Joint Photographic Experts Group.  JPEG compression offers
efficient data storage.  The data not required for displaying the image is identified and deleted.  Since the data is
deleted, JPEG algorithms are said to be irreversible.  This means that once the image is compressed, the decom-
pressed image it is not the same as the original image. PC card
TYPE (I, II and III)
BMP
JPEG
Terminology 
						

							EÐ33
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp, clean the filter, and replace the batteries
in the remote control.
Replacing the Lamp
After your lamp has been operating for 2000 hours (1500 hours :
MT1045) or longer, the ÒStatusÓ light in the cabinet will go on and
the message will appear. Even though the lamp may still be working,
replace it at 2000 (1500 hours : MT1045) hours to maintain optimal
projector performance.
CAUTION
¥ DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait a
full minute, and then disconnect the power cable. Allow at
least one hour for the lamp to cool before handling.
¥ DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
¥
The projector will turn off and go into stand by mode after 2100
(1600 hours : MT1045) hours of service. If this happens, be sure
to replace the lamp. If you continue to use the lamp after 2000
hours (1500 hours : MT1045) of use, the lamp bulb may shatter,
and pieces of glass may be scattered in the lamp case. Do not
touch them as the pieces of glass may cause injury. If this hap-
pens, contact your NEC dealer for lamp replacement.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a free-
wheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFFSOURCE
1
MENU
ENTERSELECT
POW STATUSSOURCE
2
2. Loosen the two screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The three screws are
not removable.
Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of
electrical shock. Do not attempt to circumvent this interlock.
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFFSOURCE
1
MENU
ENTERCANCELSELECT
POWER STATUS
OSOURCEAUTO ADJUST
2
3. Insert a new lamp housing until the lamp housing is plugged into
the socket.
CAUTION: Do not use a lamp other than the NEC replace-
ment lamp (MT40LP).
Order this from your NEC dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFFSOURCEAUTO ADJUST
1
MEENTERCANCELSELECT
POWER STATUSSOURCE
2
4. Reattach the lamp cover.
Tighten the lamp cover screw.
Be sure to tighten the screw.
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFFSOURCEAUTO ADJUST
1MEENTERCANCELSELECT
POWER STATUSSOURCE
2
5. After you install a new lamp, select [Main Menu] ® [Projector
Options] ® [Setup]®[Page 2]®[Clear Lamp Hour Meter] to re-
set the lamp usage hours.
NOTE: When the lamp exceeds 2100 hours (1600 hours : MT1045)
of service, the projector cannot turn on and the message is not dis-
played. If this happens, press the OFF or Help button on the remote
control for a minimum of 10 seconds while in standby mode. When
the lamp time clock is reset to zero, the STATUS indicator goes out.
Interlock 
						

							EÐ34
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/Ð) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
MENUOURCE AUTO  ADJUSTUSB
AC IN
Cleaning or Replacing the Filters
The air-filter sponge keeps the inside of the MultiSync MT840/
MT1040/MT1045 Projector free from dust or dirt and should be
cleaned after every 100 hours of operation (more often in dusty con-
ditions). If the filter is dirty or clogged, your projector may overheat.
CAUTION
¥ Turn off the power and unplug the projector before re-
placing the filter.
¥ Only clean the outside of the filter cover with a vacuum
cleaner.
¥ Do not attempt to operate the projector without a filter
cover.
¥ Your projector will not operate unless the filter cover is
installed correctly.
To clean the air-filter:
Vacuum the filter-through the filter cover.
AC IN
1
2
MENUELECTSOURCEAUTO  ADJUSTUSB
AC IN
12
To replace the air-filter:
1. Remove the filter cover by pushing up on the catch of the cover
until you feel it detach.
2. Reinstall the new filter cover.
NOTE: Do not detach the sponge from the filter cover. Do not wash
the filter cover with soap and water. Soap and water will damage the
the filter membrane. Before replacing the filter cover, remove dust
and dirt from the projector cabinet. Keep out dust and during filter
replacement. 
						

							EÐ35
5. TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector.
OFF
On continually
Blinking very rapidly (On
and off in a cycle of 1 sec.)
Blinking rapidly (On and off
in a cycle of 4 sec)
Blinking slowly  (On and off
in a cycle of 8 sec.)
Blinking very slowly  (On
and off in a cycle of 12 sec.)
Status Light Messages
Common Problems & Solutions
Condition Status
¥ Normal
¥ The projector lamp has exceeded 2000 hours (1500 hours : MT1045) of operation and should be replaced.
¥ The lamp cover or filter cover is not fastened properly. Check and reattach it if necessary.
¥ The temperature protector has been triggered. If the room temperature is high, move the projector to a
cooler location. If the temperature inside the projector is high, check the cooling fan hole on the bottom of
the projector. If the hole is blocked, remove whatever is blocking it.
¥ The cooling fan has stopped. Contact your NEC dealer for service.
¥ The lamp is not turned on.
The projector was turned off and back on too quickly. Turn off the projector, wait one minute, then turn the
projector back on. Or the lamp is burnt out.
Does not turn on
No picture
Image isnÕt square to the
screen
Picture is blurred
Image is scrolling verti-
cally, horizontally or both
Remote control does not
work
Status indicator is lit or
blinking
Cross color in RGB mode¥ Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on.
¥ Ensure that the lamp cover is installed correctly. See page E-33.
¥ Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (1600 hours : MT1045).
If there is insufficient ventilation around the projector or if the room where youÕre presenting is particu-
larly warm, move the projector to a cooler location.
¥ Use the menu to select your source (Video, S-Video, RGB or PC Card Viewer). See page E-20.
¥ Ensure your cables are connected properly.
¥ Use menus to adjust the brightness and contrast. See page E-20
¥ Remove the lens cap.
¥ Reset the settings or adjustments to factory preset levels using the Factory Default in the Adjustment
Menu. See page E-21
¥ Reposition the projector to improve its angle to the screen. See page E-12
¥ Use the Keystone in the Adjustment Menu to correct the trapezoid distortion. See page E-21
¥ Adjust the focus. See page E-12 or E-17.
¥ Reposition the projector to improve its angle to the screen. See page E-12
¥ Ensure that the distance between the projector and screen is within the adjustment range of the lens. See
page E-13
¥ Use menus or Source button on the remote control or the cabinet to select the source you want to input.
¥ Install new batteries. See page E-34.
¥ Make sure there are no obstacles between you and the projector.
¥ Stand within 22 feet (7 m) of the projector. See page E-34.
¥ Make sure that you are in the Projector mode or the Computer/Projector Select button lights in red.
If not, press the Computer/Projector Select button.
¥ See the Status Light messages above.
¥ If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image with the Position and
Pixel Adjust in the Adjustments Menu. See page E-21.
Problem Check These  Items 
						

							EÐ36
¥ Is ÒPC Card ViewerÓ selected from the Source menu?
¥ Is the PC memory card seated in the PC CARD ACCESS slot completely?
¥ Are slide data stored in the PC card?
¥ Have the contents of the PC card been destroyed?
¥ While an image with over 10242768 dots is projected, several lines of information will be lost. Use the
supplied software change the image to 10242768 dots in size.
¥ Areas of slides exceeding 10242768 (MT840: 8002600 dots)  cannot be displayed.  Use the PC Card
Viewer software, etc., to change the image size to 10242768 dots (MT840: 8002600 dots).
In addition, the displayable image size differs according to the resolution of the projector.  Use the PC Card
Viewer software, etc., to change the image size.
Note that on MT840 JPEG images exceeding 8002600 dots are scaled down to three-quarters of its
original size. Example: a JPEG image exceeding 10242768 dots is displayed in 768 (=102423/4)2576
(=76823/4) dots.
¥ Use a computer, etc., to repair the data.
Condition Status
When using the PC Card Viewer function
For more information contact your dealer.No picture
Part of a slide is not displayed
Contents of PC Card are
damaged 
						

							EÐ37
6. SPECIFICATIONS
This section provides technical information about the MultiSync MT840/MT1040/MT1045  ProjectorÕs performance.
Model Number MT840 / MT840G / MT1040 / MT1040G/ MT1045 / MT1045G
Optical
LCD Panel 1.3Ó p-Si TFT avtive-matrix, 8002600 dots (MT840) / 10242768 dots (MT1040/MT1045)
1.3Ó p-Si TFT avtive-matrix with Micro Lens Array (MT1045)
Lens Manual zoom, manual focus
MT840/MT1040 : F2.3 Ð 2.7    f=48.6 Ð 58.4 mm
MT1045 : F1.8 Ð 2.2    f=49.3 Ð 59.3 mm
Lamp MT840/MT1040 : 180W NSH lamp / MT1045 : 200W NSH lamp
Image Size 30 Ð 300 inches (762 Ð 7620 mm) diagonal
Projection Distance MT840/MT1040 : 4.3 Ð 36.7 ft (1.3 - 11.2 m)
MT1045 : 4.3 Ð 37.1 ft (1.3 - 11.3 m)
Electrical
Inputs Video (NTSC / PAL / PAL60 / SECAM / NTSC4.43)
Horizontal Frequency : 15 Ð 85 kHz (RGB : 24 kHz or over)
Vertical Frequency : 50 Ð 85 Hz
Video Bandwidth RGB: 80 MHz
Color Reproduction Full color, 16.7 million colors simultaneously.
Horizontal Resolution 550 TV lines : NTSC / PAL / NTSC4.43 / YCbCr
350 TV lines : SECAM
RGB MT840 : 800 dots horizontal, 600 dots vertical
MT1040/MT1045 : 1024 dots horizontal, 768 dots vertical
Power Requirement 100 Ð 120 / 200 Ð 240 VAC, 50 / 60 Hz
Input Current 3.5 A (100 Ð 120 VAC) / 1.7A (200 Ð 240 VAC)
Mechanical
DimensionsMT840/MT1040 : 11.1 (W)24.8 (H)214.3 (D) / 281mm (W)2121mm (H)2364mm (D) (not including lens and feet)
MT1045 : 11.1 (W)24.8 (H)214.9 (D) / 281mm (W)2121mm (H)2376mm (D) (not including lens and feet)
Net Weight MT840/MT1040 : 12.4 lbs / 5.6 kg
MT1045 : 12.8 lbs / 5.8 kg
Environmental ConsiderationsOperational Temperatures: 32û Ð 104ûF (0û to 40ûC), 20 Ð 80% humidity
Storage Temperatures: 14û Ð 140ûF (-10û to 60ûC), 30 Ð 85% humidity
Regulations UL Approved (UL 1950, CSA 950)
Meets DOC Canada requirements
Meets FCC Class A requirements
Meets AS/NZS3548
Meets EMC Directive (EN55022, EN55082-1, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
The specifications are subject to change without notice. 
						

							EÐ38
Cabinet Dimensions
MENU
ENTERCANCEL
SELECT
POWER STATUS
ON
/OFF
SOURCE AUTO  ADJUST
AC IN
PC CONTROLREMOTE
CONTROL
INPUT MOUSE
OUTPUT
USB
S-VIDEO
VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1
L
/MONO
R
1.5 (0.06)
281 (11.06)
 73.5 (2.89) 121 (4.76)
4
(0.16)6.6
(0.26)364 (14.33)
Lens center
39.5
(1.56)
Lens center
Unit = mm (inch)
MT840/MT1040 
						

							EÐ39
MT1045
MENU
ENTERCANCEL
SELECT
POWER STATUS
ON
/OFF
SOURCE AUTO  ADJUST
AC IN
PC CONTROLREMOTE
CONTROL
INPUT MOUSE
OUTPUT
USB
S-VIDEO
VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1
L
/MONO
R
PC-CARD
1.5(0.06)
281(11.06)
 73.5
(2.89)121 (4.76)
 4
(0.16)7.5 (0.3)
39.5
(1.56)
376 (14.9)
Unit = mm (inch)
Lens centerLens center 
						

							EÐ40
51423
10
11 12 13 14 156 978
D-Sub Pin Assignments
Mini D-Sub 15 Pin Connector
Pin No. RGB Signal (Analog) YCbCr Signal
1 Red Cr
2 Green or Sync on Green Y
3 Blue Cb
4 Ground
5 Ground
6 Red Ground Cr Ground
7 Green Ground Y Ground
8 Blue Ground Cb Ground
9 No Connection
10 Sync Signal Ground
11 Ground
12 Bi-directional DATA (SDA)*
13 Horizontal Sync or Composite Sync
14 Vertical Sync
15 Data Clock*
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
* RGB Input 1 only