NEC Mt1040 Lcd Projector Users Manual

EÐ11
9 Picture Mute Button
This button turns off the image and sound for a short period of
time. Press again to restore the image and sound.
10 Help Button
Provides information about operation and adjustment procedures
or the set information for the current menu or adjustment during
menu operation. This also displays information how to use the Help.
11 Power On And Off
If power is applied, you can use this button to turn your projector
on and off.
NOTE: To turn off the projector, press and hold the POWER...

EÐ12
2. INSTALLATION
This section describes how to set up your MultiSync MT840/MT1040/
MT1045 projector and how to connect video and audio sources.
Setting up Your Projector
Your MultiSync MT840/MT1040/MT1045 Projector is simple to set
up and use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying the Projector: Always carry your projector by the handle.
Ensure that the power cable...

EÐ13
D H
V
Screen (inch)
Throwing Angle  (U) Screen center
Projector foot Screen Top
Distance Chart
Screen Size D Diagonal (inch) 30 40 60 80 100 120 150 180 200 240 300Width(H) (inch) 24 32 48 64 80 96 120 144 160 192 240Width(V) (inch) 18 24 36 48 60 72 90 108 120 144 180Magnification K 23.1 30.8 46.2 61.5 76.9 92.3 115.4 138.5 153.9 184.6 230.8Throwing Distance S Wide (inch) 42.2 57.0 86.5 116.1 145.6 175.2 219.6 263.9 293.5 352.6 441.3(mm) 1071.1 1446.5 2197.5 2948.4 3699.4 4450.4 5576.8 6703.2...

EÐ14
WARNING
¥ Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more informa-
tion.
* Do not attempt to install the projector yourself.
¥ Only use your projector on a solid, level surface. If the projec-
tor falls to the ground, you can be injured and the projector
severely damaged.
¥ Do not use the projector where temperatures vary greatly. The
projector must be used at temperatures between 32ûF (0ûC)
and 104ûF (40ûC).
¥ Do not expose the...

EÐ15
Wiring Diagram
PC CONTROLREMOTE
CONTROL
INPUT MOUSE
OUT
S-VIDEO
VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1
L/MONO
R
Optional Component V cable
To video, S-video, and audio
inputs on the projector.Supplied mouse adapter (For Macintosh)
Supplied mouse adapter (For IBM PS/2)
Pin adapter for Macintosh (supplied)
Signal cable (supplied)
To mini D-Sub 15-pin connector on
the projector. It is recommended that
you use a commercially available
distribution amplifier if connecting a
signal cable longer than...

EÐ16
When using a Macintosh with the projector, set the DIP switches of
the supplied pin adapter according to your resolution. After setting,
restart your Macintosh.
See the following pages for setting of the DIP switches.
¥ When using with a Macintosh, SVGA(8002600 :MT840)/
XGA(10242768 : MT1040/MT1045) is recommended if your
Macintosh supports this mode.
¥ When using with a Macintosh PowerBook, output may not be
set to 8002600 unless ÒmirroringÓ is off on your PowerBook.
Refer to ownerÕs manual...

EÐ17
3.OPERATION
This section describes how to select a computer or video source, how
to adjust the picture, and how to customize the menu or projector
settings.
General Controls
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1. Turn on the Projector
Plug the supplied power cable in the wall outlet. The projector
will go into its standby mode and the power indicator will glow
amber.
Only after you press the ÒOnÓ button on the...

EÐ18
Mein Menu
Source Select
Adjustments
Image Options
Projector Options
Tools
Help
Source Select
RGB 1
RGB 2
Video
S-Video
PC Card Viewer
Adjustments
Picture
Volume
Image
Color Temperature
Keystone
Factory Default
Image Options
Image Mode
Video Mode
Projector Options
Menu
Setup
Tools
Capture
PC Card Files
ChalkBoard
Help
Contents
Source Information
Projector Information
Main MenuSub Menu Items
All Data/Current Signal
Gamma
Noise Reduction
Color Matrix
Orientation
Background
Signal Select
Auto Start...

EÐ19
Menu Elements
Setup
Orientation Page1 Page2 Page3
Front Floor
Background
BlueSignal Select
S-VideoAuto Video
Auto RGB1
Auto
RGB2
Auto
OKCancel Page4
Page4
Setup
Page1
Mouse
Button
Right Hand Left HandAuto Start Page2 Page3
Power Management
Power Off Confirmation
Keystone Save
Clear Lamp Hour Mater
Fan High Speed Mode
OKCancel
Sensitivity
Fast MediumSlow
Brightness
Title barTa b
Highlight
Solid triangle
Close button
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
Menu windows or...

EÐ20
Adjustments
Picture
Volume
Image
Color Temperature
Keystone
Factory Default
Menu Descriptions & Functions
Source Select
Enables you to select a video source such
as a VCR, DVD player, laser disc player,
computer or document camera depend-
ing on what is connected to your inputs.
Press the ÒSelectÓ button on the projec-
tor cabinet or st buttons on your re-
mote control to highlight the menu for
the item you want to adjust.
RGB1 and 2
Selects the computer connected to your RGB or component signal....