NEC Mt1035+ Projector Users Manual

							Part No.  78410751
Printed in Japan
NEC Multimedia Theatre
NEC Multimedia Theatre
LCD Projector UserÕs Manual
NEC Technologies, Inc.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
MultiSync
¨
MT830+ª/MT1030+ª/MT1035+ª
NEC Technologies 
						

							2
Precautions
Please read this manual carefully before using your NEC MultiSync
M T830+/MT1030+/MT1035+ LCD Projector and keep the manual
handy for future reference.
Your serial number is located under the name plate label on the right side of
your MultiSync MT830+/MT1030+/MT1035+.  Record it here:
IMPORTANT INFORMATION
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified by
NEC Technologies in this manual. Failure to comply with this
government regulation could void your right to operate this equip-
ment.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a commercial installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interfer-
ence in which case the user will be required to correct the interfer-
ence at their own expense.
DOC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interfer-
ence-Causing Equipment Regulations.
CAUTION
LASER RADIATION-
DO NOT STARE INTO BEAM
WAVE LENGTH: 645 nm (640-660 nm)
MAX. OUTPUT: 1 mW
CLASS II LASER PRODUCT
CAUTION
To turn off main power, be sure to remove the plug from power
outlet. The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABI-
NET. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage
within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind
of contact with any part inside of the unit.
This symbol alerts the user that important informa-
tion concerning the operation and maintenance of
this unit has been provided. The information should
be read carefully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE. DO NOT USE THIS UNITÕS
GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN
OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY IN-
SERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-
VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE
DONE BY QUALIFIED NEC SERVICE PERSONNEL.
1
2
INTRODUCTIONINSTALLATIONOPERATIONMAINTENANCETROUBLE SHOOTINGSPECIFICATIONS 
						

							3
Important Safeguards
These safety instructions are to ensure the long life of your LCD projector and
to prevent fire and shock. Please read them carefully and heed all warnings.
Installation
1. For best results, use your LCD projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and
moisture.
3. Do not place your LCD projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your LCD projector carefully. Dropping or jarring can damage
internal components.
6. Do not place heavy objects on top of the LCD projector.7. If installing the LCD projector on the ceiling:
a. The ceiling must be strong enough to support the LCD projector and the
installation must be in accordance with any local building codes.
b. The LCD projector must be installed by qualified NEC service personnel.
Power Supply
1. The LCD projector is designed to operate on a power supply of 100-120 or
220-240 V 50/60 Hz AC. Ensure that your power supply fits this requirement
before attempting to use your LCD projector.
2. Handle the power cable carefully and avoid excessive bending. A damaged
cord can cause electric shock or fire.
3. If the LCD projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
Cleaning
1. Unplug the LCD projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild
detergent. Never use strong detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or
mar the lens.
4. Clean the air filter with a vacuum cleaner after every 100 hours of operation.
a. Clean the outside of the filter with a vacuum cleaner.
b. Do not use water or any other liquid to clean the air filter.
c. Do not operate your LCD projector without the air filter.
Lamp Replacement
¥ Perform lamp replacement in accordance with the instructions on page 83.
¥ Be sure to replace the lamp when the Status light comes on. If you continue
to use the lamp after 2000 hours of use, the lamp bulb may shatter, and  pieces
of glass may be scattered in the lamp case. Do not touch them as the pieces of
glass may cause injury. If this happens, contact your NEC dealer for lamp
replacement.
¥ Allow a minimum of ONE minute to elapse between turning the lamp off and
on. High voltage is applied to the lamp immediately when the power is turned
on. Therefore turning the power off and quickly back on may shorten the life
of your lamp and result in damage to your LCD projector.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unobstructed to
prevent the build-up of heat inside your LCD projector. Allow at least 3
inches (10cm) of space between your LCD projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into
your LCD projector. Do not attempt to retrieve any objects that might fall into
your projector. Do not insert any metal objects such as a wire or screwdriver
into your LCD project. If something should fall into your projector, discon-
nect it immediately and have the object removed by a qualified NEC service
person.
3. Do not place any liquids on top of your LCD projector.
¥ Do not look into the lens while the projector is on. Serious damage to your
eyes could result.
¥ Do not look into the laser pointer while it is on and do not point the laser
beam at another person. Serious injury could result.
¥ Keep any items such as magnifying glass out of the light path of the
projector. The light being projected from the lens is extensive, therefore
any kind of abnormal objects that can redirect light coming out of the
lens, can cause unpredictable outcome such as fire or injury to the eyes.
¥ Do not cover the lens with the supplied lens cap or equivalent while the
projector is on. Doing so can lead to melting of the cap and possibly
burning your hands due to the heat emitted from the light output.
3
4 
						

							4
Ce symbole a pour but de prŽvenir lÕutilisateur de la
prŽsence dÕune tension dangereuse, non isolŽe se
trouvant ˆ lÕintŽrieur de lÕappareil. Elle est dÕune
intensitŽ suffisante pour constituer un risque

lÕintŽrieur de cet appareil.
Ce symbole a pour but de prŽvenir lÕutilisateur de la
prŽsence dÕimportantes instructions concernant
lÕentretien et le fonctionnement de cet appareil. Par


Importantes prŽcautions de sŽcuritŽ
Les points suivants sont des prŽcautions de sŽcuritŽ importantes destinŽes ˆ
garantir une longue durŽe de service du projecteur ˆ Žcran ˆ cristaux liquides
(LCD) et afin dÕŽviter un incendie et des risques dÕŽlectrocution. SÕassurer de
lire attentivement ces prŽcautions de sŽcuritŽ et respecter tous les
avertissements dŽcrits ci-dessous.
Installation
1. Pour un fonctionnement optimal, utiliser le projecteur ˆ Žcran ˆ cristaux

2. Placer le projecteur ˆ Žcran ˆ cristaux liquides (LCD) sur une surface ˆ niveau

3. Ne pas placer le projecteur ˆ Žcran ˆ cristaux liquides (LCD) en plein soleil,

ATTENTION
RISQUE DÕELECTROCUTION NE PAS OUVRIR
AVERTISSEMENT
AFIN DE REDUIRE LES RISQUES DÕINCENDIE OU
DÕELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA
PLUIE OU A LÕHUMIDITE. AUSSI, NE PAS UTILISER LA FICHE
POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE
PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE
INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES
COMPOSANTES HAUTE TENSION SE TROUVENT A
LÕINTERIEUR. LAISSER A UN PERSONNEL QUALIFIE LE
SOIN DE REPARER CET APPAREIL.
DOC avis de conformation
DOC avis de conformation
Cet appareil numŽrique de la classe A respecte toutes les exigences du

5
6
ATTENTION
RAYONNEMENT LASER NE PAS
REGARDER DANS LE FAISCEAU
LONGUEUR DÕONDE: 645 nm (640-660 nm)
MAX. SORTIE: 1 mW
APPREIL A LASER DE CLASSE 2
ATTENTION
Pour couper lalimentation principale, sassurer de retirer
la fiche de la prise de courant.


sible. 
						

							5
4. La fumŽe, la vapeur et lÕexposition aux rayons directs du soleil risquent de
dŽtŽriorer sŽrieusement les composantes internes.
5. Eviter des manipulations brusques lors du dŽplacement du projecteur ˆ Žcran
ˆ cristaux liquides (LCD), car un choc violent pourrait endommager les
composantes internes.
6. Ne pas deposer dÕobjets lourds sur le dessus du projecteur ˆ Žcran ˆ cristaux
liquides (LCD).
7. Lors de lÕinstallation du projecteur ˆ Žcran ˆ cristaux liquides (LCD) au
plafond, respecter les instructions suivantes.
a. 

les codes de construction locaux.
b. 
personnel qualifiŽ.
Alimentation
1. 
100-120 ou 220-240VCA 50/60Hz. SÕassurer que la tension dÕalimentation
locale satisfait cette exigence avant dÕutiliser le projecteur.
2. Manipuler le c‰ble dÕalimentation avec prŽcaution et Žviter de le plier
excessivement. Un cordon endommagŽ risque de provoquer une
Žlectrocution ou un incendie.3. Si le projecteur ˆ Žcran ˆ cristaux liquides (LCD) nÕest pas utilisŽ pendant une
pŽriode prolongŽe, retirer la fiche de la prise secteur.
Nettoyage
1. DŽbrancher le projecteur ˆ Žcran ˆ cristaux liquides (LCD) de la prise
dÕalimentation avant le nettoyage.
2. 
tenaces, utiliser une solution dÕun dŽtergent doux. Ne jamais utiliser de
dŽtergents puissants ou des solvants, tel que lÕalcool ou un diluant pour
nettoyer le projecteur ˆ Žcran ˆ cristaux liquides (LCD).
3. Utiliser un appareil diffuseur chauffant ou du papier de nettoyage de lentille
disponible dans le commerce pour nettoyer la lentille.
Ne pas frapper ou rayer la surface de la lentille, car des dŽfauts risquent de se
produire sur la surface de la lentille.
4. Nettoyer le filtre ˆ air toutes les 100 heures.
a. Nettoyer seulement lÕextŽrieur avec un aspirateur.
b. Ne pas nettoyer le filtre ˆ air avec de lÕeau ou un liquide.
c. Ne pas utiliser le projecteur ˆ Žcran ˆ cristaux liquides (LCD) sans
le filtre ˆ air.
Remplacement de la lampe
¥ Effectuer le remplacement de la lampe suivant les instructions de la page
87.
¥ Assurez-vous de bien remplacer la lampe lorsque le voyant dÕusure


ŽparpillŽes dans le compartiment de la lampe. Ne  les touchez pas car elles
peuvent vous blesser. Dans ce cas, contactez votre revendeur NEC afin de
procŽder au remplacement de la lampe.
¥ 
rallumer. Une haute tension est immŽdiatement appliquŽe ˆ la lampe quand
celle-ci est mise sous tension. Par consŽquent, Žteindre, puis tout de suite
rallumer peut abrŽger la vie de votre lampe et endommager votre projecteur
LCD.
PrŽcautions pour Žviter un incendie ou
une Žlectrocution
1. 
chaleur ˆ lÕintŽrieur du projecteur ˆ Žcran ˆ cristaux liquides (LCD). SÕassurer
que les trous de ventilation ne sont pas obstruŽs. Laisser un espace dÕau moins
10 cm (quatre pouces) entre le projecteur ˆ Žcran ˆ cristaux liquides (LCD) et
les murs.2. Eviter que des objets Žtrangers, des agrafes, des clous et du papier, par


objets mŽtalliques, des fils et des tourne-vis, par exemple ˆ lÕintŽrieur du
projecteur ˆ Žcran ˆ cristaux liquides (LCD). Si un objet tombe ˆ lÕintŽrieur
du projecteur ˆ Žcran ˆ cristaux liquides (LCD), le dŽbrancher
immŽdiatement et contacter un dŽpanneur qualifiŽ pour retirer lÕobjet.
3. Ne pas placer des liquides sur le dessus du projecteur ˆ Žcran ˆ cristaux
liquides (LCD).
¥ Ne regardez pas ˆ lÕintŽrieur de lÕobjectif lorsque le projecteur est en
marche. Vous risquez de vous blesser gravement aux yeux.
¥ 
marche et ne dirigez pas le rayon laser sur une autre personne. Vous
risquez de provoquer ue blessure grave.
¥ 


donc avoir des consŽquences imprŽvisibles, telles quun feu ou une
blessure au yeux.
¥ Ne pas couvrir la lentille avec le couvercle de lentille fourni pendant que
le projecteur est allumŽ. Le couvercle pourrait fondre et vous bruleriez

7
8 
						

							6
NEC MultiSync¨ LCD Projector
Products
NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be free
from defects in material and workmanship under the following terms.
HOW LONG IS THE WARRANTY?
Parts and labor are warranted for (2) two years from the date of the first customer
purchase. The lamp is warranted for 2000 hours of operating time or six months,
whichever comes first.
WHO IS PROTECTED?
This warranty may be enforced only by the first purchaser.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in material or
workmanship in this product. The following are not covered by the warranty:
1. Any product which is not distributed in the U.S.A. or Canada by NECTECH
or which is not purchased in the U.S.A. or Canada from an authorized
NECTECH dealer. For a listing of authorized dealers please contact
NECTECH at 800-836-0655.2. Any product on which the serial number has been defaced, modified or
removed. NECTECHÕS LIABILITY FOR ANY DEFECTIVE PRODUCT
IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT OUR OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR
ÔLIKE NEWÕ.
3. NECTECH SHALL NOT BE LIABLE FOR : Damage, deterioration or
malfunction resulting from:
a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of
nature, unauthorized product modification, or failure to follow instruc-
tions supplied with the product.
b. Repair or attempted repair by anyone not authorized by NECTECH.
c. Any shipment of the product (claims must be presented to the carrier).
d. Removal or installation of the product.
e. Any other cause which does not relate to a product defect.
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any
accessories used in connection with the product.
WHAT NEC WILL COVER
We will pay labor and material expenses for covered items. But we will not pay
for the following:
1. Removal or installation charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user
controls. These costs are the responsibility of the NECTECH dealer from
whom the product was purchased.
3. Payment of shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom you
purchased the product.
2. Whenever warranty service is required, the original dated invoice (or a copy)
must be presented as proof of warranty coverage. Please be prepared to
describe or demonstrate the problem to your dealer.
3. For the name of the nearest NECTECH authorized service center, call
NECTECH at 800-836-0655.
LIMITATION OF IMPLIED WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF DAMAGES
NECTECHÕS LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED
TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR
OPTION. NECTECH SHALL NOT BE LIABLE FOR:1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN
THIS PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS
OF USE OF THE PRODUCT, LOSS OF TIME, COMMERCIAL LOSS;
OR
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUEN-
TIAL OR OTHERWISE. SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITA-
TIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
HOW STATE LAW RELATES TO THE WARRANTY
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
FOR MORE INFORMATION, TELEPHONE 800-366-5213
NEC TECHNOLOGIES, INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
NOTE:   All products returned to NECTECH for service MUST have
prior approval. To get approval, call NEC Technologies at
800-836-0655.
LIMITED WARRANTY9
10 
						

							7
1. Introduction
Introduction To The MultiSync MT830+/MT1030+/MT1035+ LCD Projector .............. 13
How Do You Get Started? ............................................................................................... 15
WhatÕs In The Box? ........................................................................................................ 15
Getting To Know Your MultiSync MT830+/MT1030+/MT1035+ LCD Projector ......... 17
Front / Rear Features ................................................................................................ 17
Side Features ........................................................................................................... 18
Top Features ............................................................................................................ 19
Terminal Panel Features ........................................................................................... 21
Remote Control Features ......................................................................................... 25
2. Installation
Setting Up Your MultiSync MT830+/MT1030+/MT1035+ LCD Projector .................... 31
Selecting A  Location ................................................................................................ 32
Using A Tabletop Or Cart ......................................................................................... 33
Ceiling Installation ................................................................................................... 41
Reflecting The Image ............................................................................................... 47
Rear Screen Projection ............................................................................................. 48
Wiring Diagram .............................................................................................................. 49
Connecting Your PC Or Macintosh Computer ................................................................ 51
Connecting Your Document Camera ............................................................................... 57
Connecting Your VCR Or Laser Disc Player .................................................................. 57
Connecting An External Monitor .................................................................................... 58
Connecting Your Computer To The Mouse Output Port .................................................. 59
TABLE OF CONTENTS
3. Operation
General Controls ............................................................................................................. 61
Using The Menus ............................................................................................................ 63
Menu Descriptions & Functions ..................................................................................... 65
Source Menu (Source Icons) .................................................................................... 65
Image Adjust Menu(Sound And Picture Control Icons) ........................................... 67
Power Menu(Projector Control Icons) .................................................................... 71
Settings Menu(Maintenance Icons) .......................................................................... 73
Using the Viewer function ....................................................................................... 75
4. Maintenance
Replacing The Lamp ....................................................................................................... 83
Cleaning Or Replacing The Filter ................................................................................... 85
Remote Control Battery Installation ................................................................................ 86
5. Troubleshooting
Status Light Messages ..................................................................................................... 91
Common Problems & Solutions ...................................................................................... 93
6. Specifications
Optical ............................................................................................................................ 95
Electrical ......................................................................................................................... 96
Mechanical .....................................................................................................................96
D-Sub Pin Assignments .................................................................................................. 99
Timing Chart ................................................................................................................. 101
PC Control Command Reference .................................................................................. 103
Cable Connection .......................................................................................................... 107
11
12 
						

							8
This section introduces you to your new MultiSync MT830+ (SVGA)/
MT1030+ and MT1035+ (XGA) LCD Projector, provides a list of
materials that comes with your projector and describes the features and
controls.
Congratulations On Your Purchase Of The MultiSync
MT830+/MT1030+/MT1035+ LCD Projector
The MultiSync MT830+/MT1030+/MT1035+ is one of the very
best LCD projectors available today. The multiple LCD panels en-
able you to project precise images up to 300 inches (MT830+/
MT1030+) / 320 inches (MT1035+) across (measured diagonally)
from your PC or Macintosh computer (desktop or notebook), VCR,
DVD player, document camera, or even a laser disc player.
You can use the projector on a tabletop or cart, you can permanently
mount it on a ceiling*
1, or you can use MultiSync MT830+/
MT1030+/MT1035+ LCD Projector to project images from behind
the screen. The remote control can be used wirelessly or with a cable,
and you can even use the remote control with the built-in remote
mouse receiver to operate the mouse on your PC or Mac. But best of
all, the MultiSync MT830+/MT1030+/MT1035+ is an NEC LCD
projector. That means you can depend on years of reliable perfor-
mance and crystal-clear presentations!
INTRODUCTION 1
Features youÕll enjoy:
¥ Simple set up and operation.
¥ Hot air blown from the vents does not bother the audience during
your presentation since the vents are located on the front.
¥
A high-performance 150 watt short arc high pressure lamp that is guar-
anteed for 2000 hours of service or six months, whichever comes first.
¥ A wireless remote control that operates the projector from any
angle.
¥ A laser pointer that s built into the remote control.
¥ The power zoom control enables you to adjust the image to be
between 20 and 300 inches (MT830+/MT1030+) / 25 and 320
inches (MT1035+) (measured diagonally).
¥ Keystone correction allows you to correct trapezoidal distortion
so that the image is square.
¥ White balance control allows you to adjust the brightness and
contrast for each RGB color.
¥ You can choose between video modes depending on your source:
normal for a typical picture, natural for true color reproduc-
tion, and camera for use with a document camera or low APL
picture.
¥ The optional MT Viewer kit allows you to start your presentation
even when a PC is not available at the site.
¥ The image capture enables you to use the entire picture as a
background image or to create slides (optional MT Viewer re-
quired).
¥ An image can be projected from in front or behind a screen, and
the projector can even be installed on the ceiling.
¥ NEC Technologies exclusive AccuBlendª intelligent pixel
blending technology - an extremely accurate image compression
technology - offers a crisp image with SXGA (128021024)
resolution*
3. You can select any point on the screen with the
pointer and enlarge the selected area.
¥
Supports most IBM VGA, SVGA, XGA*2, SXGA(with
AccuBlend)*3, Macintosh, or any other RGB signals within a hori-
zontal frequency range of 15.754 to 85 kHz and a vertical frequency
range of 50 to 85 Hz. This includes NTSC, PAL, SECAM and
NTSC4.43 standard video signals.
Note:  Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in western Europe.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
¥ The remote control can be used with or without a cable, and you
can even use the remote to operate your PC or Macintosh mouse
wirelessly from across the room with the built-in remote mouse
receiver.
¥ You can control your MultiSync MT830+/MT1030+/MT1035+
LCD Projector with a PC.
¥ The contemporary cabinet design is compact, easy to carry, and
complements any office, board room or auditorium.
¥ Eight kinds of pointers are available for your presentation.
*
1Installing the MultiSync MT830+/MT1030+/MT1035+ LCD
Projector on the ceiling must be done by authorized NEC techni-
cians. Consult your NEC dealer for more information.
*
2An XGA image (10242768) is converted into a 8002600 crisp
image with NEC technologys AccuBlend.
*
3An SXGA image (128021024) is converted into a 10242768
crisp image with NEC technologys AccuBlend.
INTRODUCTION13
14 
						

							9
How Do You Get Started?
The fastest way to get started is to take your time and do everything right the first
time. Take a few minutes now to watch the introductory video and review the
manual. This may save you hours later on. At the beginning of each section of the
manual youll find an overview. If the section doesnt apply, you can skip it.
WhatÕs In The Box?
Make sure your box contains everything listed. If any pieces are missing, contact
your dealer. Please save the original box and packing materials if you ever need to
ship your MultiSync MT830+/MT1030+/MT1035+ LCD Projector.
¥ NEC MultiSync MT830+/MT1030+/MT1035+ LCD Projector
¥ Remote Control With Built-In Laser Pointer And Cables
¥ Mouse Adapter for IBM PS/2 and Mac
¥ Serial Cable
¥ Signal Cable (15-Pin Mini D-Sub To 15-Pin Mini D-Sub Connector)
¥ Pin Adapter for Macintosh
INTRODUCTION15
16
Batteries (AA22) Pin adapter for
MacintoshRemote cable
Remote control
Mouse adapter (For Macintosh)
MultiSync
MT1020 and MT820Accessories
Accessory catalog
MultiSyncMT830+/MT10 30+/MT1035+UserÕs manual
Signal cable
(15-Pin Mini D-Sub To 15-Pin Mini D-Sub connector)
Power cable
MultiSync MT 
Series
LCD Projector
Registration cardMouse adapter (For IBM PS/2)
Introductory video
Serial cable
String and rivet
Quick Connect GideQuick connect guide
¥ Power Cable
¥ Two AA Batteries
¥ Quick Connect Guide
¥ Introductory Video¥ Users Manual
¥ Accessory Catalog
¥ Registration Card
¥ String and rivet 
						

							10
PC CONTROL MOUSE OUTPUTREMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
AC IN
Built-In Speaker
(2W)
Getting To Know Your MultiSync MT830+/MT1030+/MT1035+
LCD Projector
AC Input
Plug the female end of the supplied
power cable here, and the male end
into a properly grounded outlet.Remote Sensor
Filter Cover Rear Feet
Slot for Kensington
MicroSaver Security System
Main Power Switch
Right Side Features
Lamp Cover
Lamp Cover Set Screw
Left Side Features
Remote Sensor Remote Sensor
Front Features
One-Touch
Tilt button
Lens And Lens Cap Remote Sensor
Front Vent
Front Feet
Rear Features
Carrying Handle
INTRODUCTION17
18
One-Touch
Tilt button
Built-In Speaker
(2W)
Slot Cover for the Optional
MT Viewer Board.
Latch
Carrying Handle
Terminal Panel
Connector Cap