NEC MobilePro 780 Portable Computer Users Guide

  
Using the NEC MobilePro  4-29 
2. Remove the main battery as follows: 
!Locate the battery lock and release latch on the 
bottom of the system. 
!Slide the lock to the unlocked position in the 
direction of the arrow, as indicated in the 
following figure. 
!Slide the release latch in the direction of the ar-
row, as indicated in the following figure, and hold 
it. 
!Remove the battery from the bay. 
Removing the battery pack 
A
 – Battery release latch  B
 – Battery release lock  C
 – Battery pack 
  

  
4-30  Using the NEC MobilePro 
3. Locate the full reset button inside of the battery bay, as 
indicated in the following figure. 
               Full reset button 
A
 – Full reset button  B
 – Battery connectors 
4. Using the stylus, press the full reset button. This resets 
the unit and restores your system to its original ship-
ping configuration. 
You may be able to use a recent backup of your data to 
restore your system to a more recent configuration. Re-
fer to Microsoft ActiveSync on your host...

  
Setting Up a Remote Connection  5-1 
 
Setting Up a Remote 
Connection 
!Preparing for Connection Setup 
!Connecting the Internal Modem 
!Connecting to an 
Internet Service Provider (ISP) 
!Connecting to a Remote Access 
Server 
!Sending and Receiving Email 
!Activating a Connection 
5   

  
5-2  Setting Up a Remote Connection 
PREPARING FOR CONNECTION SETUP 
Before you set up a dial-up connection for an internet ser-
vice provider (ISP) or remote access server (RAS), and the 
associated email properties, you need the following. 
!a modem (your NEC MobilePro is equipped with an 
internal data/fax modem). 
!an ISP or RAS account. 
!configuration information from your ISP or network 
administrator that may include some or all of 
the following: 
 the dial-up telephone number 
 TCP/IP...

  
Setting Up a Remote Connection  5-3 
CONNECTING THE INTERNAL MODEM 
Follow these steps to connect an RJ-11 telephone cable to 
the internal modem. 
1. Locate the modem cover on the right side of the NEC 
MobilePro and open it by pulling down the top of the 
cover. 
2. Carefully plug the RJ-11 telephone cable into the 
modem connector. 
                   Connecting the telephone cable 
!WARNING 
Do not connect the internal modem to a digital pri-
vate branch exchange connector, or the digital side 
of...

  
5-4  Setting Up a Remote Connection 
3. Connect the other RJ-11 connector into an active 
(analog) phone jack. 
Now you are ready to create a connection for an ISP or 
RAS account! 
CONNECTING TO AN INTERNET SERVICE PROVIDER 
Once you have established an account with an ISP and 
gathered the necessary configuration information, you are 
ready to create a connection on your MobilePro for your 
ISP account. 
Your Bonus Software CD may contain the application, 
Ruksun
® ConnectForce™ that enables you to...

  
Setting Up a Remote Connection  5-5 
8. Tap Next and enter the required dial-up telephone 
number. Tap Finish. 
Once your ISP connection is established you can configure 
your MobilePro for sending and receiving email through 
your ISP. Follow the instructions in “Sending and Receiv-
ing Email” and “Activating a Connection,” later in this 
chapter, to send and receive email through your ISP. 
For ISP settings, access: 
http://www.cewindows.net/wce/isp.htm/. Although not an 
official NECC web site,...

  
5-6  Setting Up a Remote Connection 
8. Tap Next and enter the required dial-up telephone 
number. Tap Finish. 
Once your RAS connection is established you can config-
ure your MobilePro for sending and receiving email 
through your RAS. Follow the instructions in “Sending 
and Receiving Email” and “Activating a Connection,” later 
in this chapter, to send and receive email through your 
RAS. 
SENDING AND RECEIVING EMAIL 
Before configuring the necessary email service informa-
tion you need some or...

  
Setting Up a Remote Connection  5-7 
The Mail Services Definition screen consists of Re-
quired information and Optional information. Fill in 
all information as provided by your ISP or network 
administrator. 
!Enter ISP information as follows: 
 POP3 Host — ISP POP3 Host name. 
 User ID — Your user id. 
 Password — Your password, if required. 
 SMTP Host — ISP SMTP Host name. 
 Return Address — Your email address. (If in a 
unix environment ). 
!Enter RAS (Exchange server) information as fol-...

  
5-8  Setting Up a Remote Connection 
ACTIVATING A CONNECTION 
Once you have created a new connection for each desired 
service, you must activate the connection with that service 
to open communication and send or receive email. 
Follow these steps to activate a connection. 
1. Double tap the Inbox icon. 
2. Tap Services and verify that the service you want to 
connect is selected. 
The currently selected service displays in the drop-
down menu and is designated with a dot. If necessary, 
modify your...