NEC Mcu 5000a Multipoint Control Unit Equipment Manual
Here you can view all the pages of manual NEC Mcu 5000a Multipoint Control Unit Equipment Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 521
NECA 340-4 14- 30 0 Revisio n 2.0 Page 1 o f 2 MCU 5000A Multipoint Control U nit COP-175 RCLK
Page 522
Page 2 of 2 NECA 340-414-300 Revision 2.0 COP-175 MCU 5000A Multipoint Control Unit This page is for your notes.
Page 523
NECA 340-4 14- 30 0 Revisio n 2.0 Page 1 o f 2 MCU 5000A Multipoint Control U nit COP-176 WCLK
Page 524
Page 2 of 2 NECA 340-414-300 Revision 2.0 COP-176 MCU 5000A Multipoint Control Unit This page is for your notes.
Page 525
NECA 340-4 14- 30 0 Revisio n 2.0 Page 1 o f 2 MCU 5000A Multipoint Control U nit COP-177 RLCS
Page 526
Page 2 of 2 NECA 340-414-300 Revision 2.0 COP-177 MCU 5000A Multipoint Control Unit This page is for your notes.
Page 527
NECA 340-4 14- 30 0 Revisio n 2.0 Page 1 o f 6 MCU 5000A Multipoint Control U nit COP-178 STLP
Page 528
Page 2 of 6 NECA 340-414-300 Revision 2.0 COP-178 MCU 5000A Multipoint Control Unit Figure 1: Loopback Point for 1.5M LIF INTERFACE Figure 2: Loopback Point for RS 422 LIF INTERFACE RELAY IPAF MTSC MTSCMTSC MTSC PN CHECKER PN GENERATOR POINT A POINT B POINT C POINT D POINT E POINT F HSCX A CODEC POINT HPOINT G RELAY MTSC MTSCMTSC MTSC PN CHECKER PN GENERATOR POINT A POINT B POINT C POINT D POINT FRS-422 LIF UNIT EC H221 MUX UNIT V SW/LSD UNIT HSCX A CODEC POINT H POINT G
Page 529
![Page 529
NECA 340-414-300 Revision 2.0 Page 3 of 6
MCU 5000A Multipoint Control Unit COP-178
STLP
System Setting and Maintenance
(continued)
INPUT FORMAT
STLP
__xy__p1[__p2] ¿
EXPLANATION OF INPUT PARAMETERS
x= A, B, C, D, E, F, G, H, or P
Specifies the point at which the test or input signal is looped back.
If P is specified, the test loop is removed. Valid values for x are:
A, B, C, D, E, F, G, H, or P
y= L or R
Specifies the type of loopback. Valid values for y are:
L: local-side loopback
R: remote-side...](http://img.usermanuals.tech/thumb/54/84243/w300_nec-mcu-5000a-equipment-manual_d-528.png "Page 529
NECA 340-414-300 Revision 2.0 Page 3 of 6
MCU 5000A Multipoint Control Unit COP-178
STLP
System Setting and Maintenance
(continued)
INPUT FORMAT
STLP
__xy__p1[__p2] ¿
EXPLANATION OF INPUT PARAMETERS
x= A, B, C, D, E, F, G, H, or P
Specifies the point at which the test or input signal is looped back.
If P is specified, the test loop is removed. Valid values for x are:
A, B, C, D, E, F, G, H, or P
y= L or R
Specifies the type of loopback. Valid values for y are:
L: local-side loopback
R: remote-side...")
NECA 340-414-300 Revision 2.0 Page 3 of 6 MCU 5000A Multipoint Control Unit COP-178 STLP System Setting and Maintenance (continued) INPUT FORMAT STLP __xy__p1[__p2] ¿ EXPLANATION OF INPUT PARAMETERS x= A, B, C, D, E, F, G, H, or P Specifies the point at which the test or input signal is looped back. If P is specified, the test loop is removed. Valid values for x are: A, B, C, D, E, F, G, H, or P y= L or R Specifies the type of loopback. Valid values for y are: L: local-side loopback R: remote-side...
Page 530
Page 4 of 6 NECA 340-414-300 Revision 2.0
COP-178 MCU 5000A Multipoint Control Unit
STLP
System Setting and Maintenance
(continued)
The combinations of the parameters x, y, p
1, and p2 are shown below.
x
y ______________p1,p2_____________ LOOPBACK______
A L p
1=1 to 8: teleconference port number Local-side loopback at A
p
2=0: bit rate used for teleconference video
9: 1.536Mb/s
B L p
1=1 to 8: teleconferences port number Local-side loopback at B
p
2= not used
C L p
1=1 to 8:...