NEC M361x Portable Projector Users Manual

							81
5. Using On-Screen Menu
Selecting	Aspect	Ratio	[ASPECT	RATIO]
The	term	“aspect	ratio” 	refers	to	the	ratio	of	width	to	height	of	a	projected	image.
The	projector	automatically	determines	the	incoming	signal	and	displays	it	in	its	appropriate	aspect	ratio.
•	This	table	shows	typical	resolutions	and	aspect	ratios	that	most	computers	support.
ResolutionAspect	RatioVGA640	×	4804:3
SVGA800	×	6004:3
XGA1024	×	7684:3
WXGA1280	×	76815:9
WXGA1280	×	80016:10
WXGA+1440	×	90016:10
SXGA1280	×	10245:4
SXGA+1400	×	10504:3
UXGA1600	×	12004:3
WUXGA1920	×	120016:10
OptionsFunction
AUTO
The	 projector	 will	automatically	 determine	the	incoming	 signal	and	display	 it	in	 its	 aspect	
ratio. 	(→ next	page)
The	projector	 may	erroneously	 determine	the	aspect	 ratio	depending	 on	its	signal. 	If	 this	
occurs,	select	the	appropriate	aspect	ratio	from	the	following.
4:3The	image	is	displayed	in	4:3	aspect	ratio.
16:9The	image	is	displayed	in	16:9	aspect	ratio.
15:9The	image	is	displayed	in	15:9	aspect	ratio.
16:10The	image	is	displayed	in	16:10	aspect	ratio.
WIDE	ZOOM
(M361X/M311X/M271X)
The	image	is	stretched	left	and	right. 	
Parts	of	the	 displayed	 image	are	cropped	 at	the	 left	and	 right	 edges	 and	therefore	 not	
visible.
LETTERBOX
(M311W/M271W)
The	 image	 of	a	letterbox	 signal	is	stretched	 equally	in	the	 horizontal	 and	vertical	 direc-
tions	to	fit	the	 screen. 	Parts	 of	the	 displayed	 image	are	cropped	 at	the	 top	and	 bottom	
edges	and	therefore	not	visible.
NATIVEThe	projector	 displays	the	current	 image	in	its	 true	 resolution	 when	the	incoming	 computer	
signal	has	a	lower	resolution	than	the	projector’s	native	resolution.
[Example	 1]	When 	the 	incoming	
signal 	with 	the 	resolution 	of 	800	
×	 600	 is	displayed	 on	the	 M361X/
M311X/M271X:
[Example	 2]	When 	the 	incoming	
signal	 with	the	resolution	 of	800	 ×	
600	 is	displayed	 on	the	 M311W/
M271W:
NOTE:
•	 When	a	non-computer	signal	is	displayed,	the	[NATIVE]	is	not	available.
•	 When	 a	signal	 with	a	higher	 resolution	 than	the	projector’s	 native	resolution	 is	displayed,	 [NA-
TIVE]	is	not	available. 	 
						

							82
5. Using On-Screen Menu
Sample	image	when	the	appropriate	aspect	ratio	is	automatically	determined
M361X/M311X/M271X
[Computer	signal]
Aspect	ratio	of	incoming	signal4:35:416:9 15:916:10
Sample	image	when	the	appro-priate	 aspect	 ratio	is	automati-cally	determined
[Video	signal]
Aspect	ratio	of	incoming	signal4:3 Letterbox Squeeze
Sample	image	when	the	as-pect	 ratio	 is	automatically	 de-
termined
NOTE:	 To	display	 a	squeezed	 signal	prop-erly,	select	[16:9]	or	[WIDE	ZOOM].
M311W/M271W
[Computer	signal]
Aspect	ratio	of	incoming	signal4:3 5:416:9 15:916:10
Sample	image	when	the	appro-priate	 aspect	 ratio	is	automati-cally	determined
[Video	signal]
Aspect	ratio	of	incoming	signal4:3 Letterbox Squeeze
Sample	image	when	the	as-pect	 ratio	 is	automatically	 de-
termined
NOTE:	 To	display	 a	letterbox	 signal	prop-erly,	select	[LETTERBOX].NOTE:	 To	display	 a	squeezed	 signal	prop-erly,	select	[16:9].
TIP:
•	 Image	position	can	be	adjusted	vertically	using	[POSITION]	when	the	[16:9],	[15:9],	or	[16:10]	aspect	ratios	are	selected.
•	 The	 term	“letterbox”	 refers	to	a	more	 landscape-oriented	 image	when	compared	 to	a	4:3	 image,	 which	is	the	 standard	 aspect	
ratio	for	a	video	source.
	 The	letterbox	signal	has	aspect	ratios	with	the	vista	size	“1.85:1”	or	cinema	scope	size	“2.35:1”	for	movie	film.
•	 The	term	“squeeze”	refers	to	the	compressed	image	of	which	aspect	ratio	is	converted	from	16:9	to	4:3.
Adjusting	the	 Vertical	Position	of	Image	[POSITION]	(not	available	on	M311W/M271W)
(only	when	[16:9],	[15:9],	or	[16:10]	is	selected	for	[ASPECT	RATIO])
When	[16:9],	 [15:9],	or	[16:10]	 is	selected	 in	[ASPECT	 RATIO],	the	image	 is	displayed	 with	black	 borders	 on	the	 top	
and bottom.
You	can	adjust	the	vertical	position	from	the	top	to	the	bottom	of	the	black	area.
  
						

							83
5. Using On-Screen Menu
 Menu Descriptions & Functions [SETUP]
[GENERAL]
Enabling	Auto	Keystone	[AUTO	KEYSTONE]
This	feature	allows	the	projector	to	detect	its	tilt	and	correct	vertical	distortion	automatically.
To	turn	on	the	AUTO	KEYSTONE	feature,	select	[ON].	To	adjust	the	KEYSTONE	feature	manually,	select	[OFF].
NOTE:	 The	[AUTO	 KEYSTONE]	 function	is	not	 available	 when	an	orientation	 type	such	 as	[CEILING	 REAR],	[DESKTOP	 REAR],	
[CEILING	FRONT]	other	than	[DESKTOP/FRONT]	is	selected	for	[ORIENTATION].
Correcting	 Vertical	Keystone	Distortion	Manually	[KEYSTONE]
You	can	correct	vertical	distortion	manually. 	(→	page	21)
TIP:	When	this	option	is	highlighted,	pressing	the	ENTER	button	will	display	its	slide	bar	for	adjustment.
Saving	Vertical	Keystone	Correction	[KEYSTONE	SAVE]
This	option	enables	you	to	save	your	current	keystone	settings.
OFF ������������������������Does  not  save  current  keystone  correction  settings �  It  will  return  your  keystone  correction  settings  to 
“zero”�
ON �������������������������Saves current keystone correction settings
Saving	your	change	once	affects	all	sources. 	The	changes	are	saved	when	the	projector	is	turned	off.
NOTE:	 When	[AUTO	 KEYSTONE]	 is	set	 to	[ON],	 [KEYSTONE	 SAVE]	is	not	 available.	 Next	time	you	turn	 on	the	 power,	 the	AUTO	
KEYSTONE	function	will	work	and	the	data	stored	with	[KEYSTONE	SAVE]	will	be	invalid. 
						

							84
5. Using On-Screen Menu
Using	the	Wall	Color	Correction	[WALL	COLOR]
 
This	function	allows	for	quick	adaptive	color	correction	in	applications	where	the	screen	material	is	not	white.
NOTE:	Selecting	[WHITEBOARD]	reduces	lamp	brightness.
Setting	Eco	Mode	[ECO	MODE]
The	ECO	MODE	increases	lamp	life,	while	lowering	power	consumption	and	cutting	down	on	CO2 emissions. 
Four	brightness	modes	of	the	lamp	can	be	selected: 	[OFF],	[AUTO	ECO],	[NORMAL]	and	[ECO]	modes.	
(→	page	27) 
						

							85
5. Using On-Screen Menu
Setting	Closed	Caption	[CLOSED	CAPTION]
This	option	 sets	several	 closed	caption	 modes	that	allow	 text	to	be	 superimposed	 on	the	 projected	 image	of	Video	
or	S-Video.
OFF ������������������������This exits the closed caption mode�
CAPTION 1-4 ���������Text is superimposed�
TEXT 1-4 ����������������Text is displayed�
NOTE:
•	 The	closed	caption	is	not	available	under	the	following	conditions:
-	 when	messages	or	menus	are	displayed.
-	 when	an	image	is	magnified,	frozen,	or	muted.
•	 Portions	 of	superimposed	 text	or	closed	 caption	 may	be	truncated.	 If	that	 happens,	 try	to	place	 the	superimposed	 text	or	
closed	caption	within	the	screen.
Using	Off	 Timer	[OFF	 TIMER]
1.	 Select	your	desired	time	between	30	minutes	and	16	hours: 	OFF,	0:30, 	1:00,	2:00,	4:00,	8:00,	12:00, 	16:00.
2.	 Press	the	ENTER	button	on	the	remote	control.
3.	 The	remaining	time	starts	counting	down.
4.	 The	projector	will	turn	off	after	the	countdown	is	complete.
NOTE:
•	 To	cancel	the	preset	time,	set	[OFF]	for	the	preset	time	or	turn	off	the	power.
•	 When	 the	remaining	 time	reaches	 3	minutes	 before	the	projector	 is	turned	 off,	the	[THE	 PROJECTOR	 WILL	TURN	 OFF	WITHIN	 3	
MINUTES]	message	will	be	displayed	on	the	bottom	of	the	screen.
Selecting	Menu	Language	[LANGUAGE]
You	can	choose	one	of	29	languages	for	on-screen	instructions.
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
[MENU]
Selecting	Menu	Color	[COLOR	SELECT]
You	can	choose	between	two	options	for	menu	color: 	COLOR	and	MONOCHROME.
Turning	On	/	Off	Source	Display	[SOURCE	DISPLAY]
This	option	 turns	on	or	off	 input	 name	 display	 such	as	COMPUTER	 1,	COMPUTER2,	 HDMI,	VIDEO,	 S-VIDEO,	
VIEWER,	NETWORK,	USB	DISPLAY,	to	be	displayed	on	the	top	right	of	the	screen.
When	no	input	 signal	 is	present,	 the	no-signal	 guidance	 prompting	 you	to	check	 for	an	available	 input	will	be	displayed	
at	the	 center	 of	the	 screen. 	When	 the	[VIEWER]	 or	[NETWORK]	 item	is	selected	 for	[SOURCE],	 the	no-signal	 guid-
ance	will	not	be	displayed. 
						

							86
5. Using On-Screen Menu
Turning	ON/OFF	Control	ID	[ID	DISPLAY]
ID DISPLAY �����������This option turns on or off the ID number which is displayed when the ID SET button on the remote control 
is pressed�
Turning	On	/	Off	Eco	Message	[ECO	MESSAGE]
This	option	turns	on	or	off	the	following	messages	when	the	projector	is	turned	on. 	
The	Eco	Message	 prompts	the	user	 to	save	 energy. 	When	 [OFF]	is	selected	 for	[ECO	 MODE],	 you	will	get	 a	message	
to	prompt	you	to	select	[AUTO	ECO],	[NORMAL],	or	[ECO]	for	[ECO	MODE].
When	[AUTO	ECO],	[NORMAL],	or	[ECO]	is	selected	for	[ECO	MODE]
To	 close	 the	message,	 press	any	one	 of	the	 buttons. 	The	 message	 will	disappear	 if	no	 button	 operation	 is	done	 for	
30 seconds.
When	[OFF]	is	selected	for	[ECO	MODE]
Pressing	the	ENTER	button	will	display	the	[ECO	MODE]	screen. 	(→	page	27)
To	close	the	message,	press	the	EXIT	button.
Selecting	Menu	Display	Time	[DISPLAY	TIME]
This	option	 allows	 you	to	select	 how	long	 the	projector	 waits	after	the	last	 touch	 of	a	button	 to	turn	 off	the	 menu. 	The	
preset	 choices	 are	[MANUAL],	 [AUTO	5	SEC],	 [AUTO	 15	SEC],	 and	[AUTO	 45	SEC]. 	The	 [AUTO	 45	SEC]	 is	the	 fac-
tory	preset.
Selecting	a	Color	or	Logo	for	Background	[BACKGROUND]
Use 	this 	feature 	to 	display 	a 	blue/black 	screen 	or 	logo 	when 	no 	signal 	is 	available. 	The 	default 	background 	is	
[BLUE].
NOTE:	
•	 If	 the	[LOGO]	 item	is	selected	 for	[BACKGROUND]	 with	the	[NETWORK]	 or	[USB	 DISPLAY]	 source	selected,	 the	[BLUE]	 item	will	
be	selected	regardless	of	its	selection.
•	 When	 [SOURCE	 DISPLAY]	 is	turned	 on,	the	no-signal	 guidance	prompting	 you	to	check	 for	an	available	 input	will	be	displayed	
at	the	center	of	the	screen	regardless	of	its	selection.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Selecting	Interval	 Time	for	Filter	Message	[FILTER	MESSAGE]
This	option	 allows	 you	to	select	 the	time	 preference	 between	displaying	 the	message	 for	cleaning	 the	filters. 	Clean	
the	filter	when	you	get	the	message	 “PLEASE	CLEAN	THE	FILTER.”	(→	page	114)
Six	options	are	available: 	
M311X/M271X/M271W:	OFF,	100[H],	500[H],	1000[H],	2000[H],	6000[H]
M361X/M311W:	OFF,	100[H],	500[H],	1000[H],	2000[H],	5000[H]
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu. 
						

							87
5. Using On-Screen Menu
[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	 your	image	 for	your	 type	of	projection. 	The	 options	 are:	desktop	 front	projection,	 ceiling	rear	projection,	
desktop	rear	projection,	and	ceiling	front	projection.
DESKTOP	FRONTCEILING	REAR
DESKTOP	REARCEILING	FRONT
Disabling	the	Cabinet	Buttons	[CONTROL	PANEL	LOCK]
This	option	turns	on	or	off	the	CONTROL	PANEL	LOCK	function.
NOTE:
•	 This	CONTROL	PANEL	LOCK	does	not	affect	the	remote	control	functions.
•	 When	 the	control	 panel	is	locked,	 pressing	 and	holding	 the	EXIT	 button	 on	the	 projector	 cabinet	for	about	 10	seconds	 will	change	
the	setting	to	[OFF].
TIP:	When	the	[CONTROL	PANEL	LOCK]	is	turned	on,	a	key	lock	icon	[		]	will	be	displayed	at	the	bottom	right	of	the	menu.
Enabling	Security	[SECURITY]
This	feature	turns	on	or	off	the	SECURITY	function.
Unless	the	correct	keyword	is	entered,	the	projector	cannot	project	an	image. 	(→	page	29)
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu. 
						

							88
5. Using On-Screen Menu
Selecting	Communication	Speed	[COMMUNICATION	SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	38400	 bps.	The	
default	 is	38400	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	 equip-
ment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE:	Your	selected	communication	speed	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Setting	ID	to	the	Projector	[CONTROL	ID]
You	can 	operate 	multiple 	projectors 	separately 	and 	independently 	with 	the 	single 	remote 	control 	that 	has 	the 	CONTROL	
ID	 function. 	If	 you	 assign	 the	same	 ID	to	all	 the	 projectors,	 you	can	 conveniently	 operate	all	the	 projectors	 together	
using	the	single	remote	control. 	To	do	so,	you	have	to	assign	an	ID	number	to	each	projector.
CONTROL ID NUMBER �������Select a number from 1 to 254 you wish to assign to your projector �
CONTROL ID �����������������������Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set -
ting�
NOTE:	
•	 When	[ON]	is	selected	 for	[CONTROL	 ID],	the	projector	 cannot	be	operated	 by	using	 the	remote	 control	that	does	 not	support	
the	CONTROL	ID	function.	(In	this	case	the	buttons	on	the	projector	cabinet	can	be	used.)
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
•		 Pressing	 and	holding	 the	ENTER	 button	on	the	 projector	 cabinet	for	10	seconds	 will	display	 the	menu	 for	canceling	 the	Control	
ID.
Assigning	or	Changing	the	Control	ID
1.	 Turn	on	the	projector.
2.	 Press	the	ID	SET	button	on	the	remote	control.
	 The	CONTROL	ID	screen	will	be	displayed.
	 If	 the	projector	 can	be	operated	 with	the	current	 remote	control	ID,	the	 [ACTIVE]	 will	be	displayed. 	If	 the	 projector	
cannot	 be	operated	 with	the	current	 remote	control	ID,	the	 [INACTIVE]	 will	be	displayed. 	To	 operate	 the	inactive	
projector,	assign	the	control	ID	used	for	the	projector	by	using	the	following	procedure	(Step	3).
3.	 Press	 one	of	numeric	 keypad	buttons	 while	pressing	 and	holding	 the	ID	SET	
button on the remote control.
 Example:
	 To	assign	 “3”,	press	the	 “3”	button	on	the	remote	control.
	 No	 ID	means	 that	all	the	 projectors	 can	be	operated	 together	with	a	single	 remote	
control. 	To	set	 “No	ID”,	enter	 “000”	or	press	the	CLEAR	button.
TIP:	The	range	of	IDs	is	from	1	to	254.
4.	 Release	the	ID	SET	button.
	 The	updated	CONTROL	ID	screen	will	be	displayed.
NOTE:	
•		 The	IDs	can	be	cleared	in	a	few	days	after	the	batteries	are	run	down	or	removed.
•		 Accidentally	 pressing	any	one	 of	the	 buttons	 of	the	 remote	 control	will	clear	 currently	 specified	
ID	with	batteries	removed. 
						

							89
5. Using On-Screen Menu
Using	Test	Pattern	[TEST	PATTERN]
Displays	 the	test	 pattern	 to	check	 for	image	 distortion	 at	the	 time	 of	the	 projector	 setup.	Press	 the	ENTER	 button	to	
display	 the	test	 pattern; 	press	 the	EXIT	 button	 to	close	 the	test	 pattern	 and	return	 to	the	 menu. 	Menu	 operation	 and	
keystone	correction	are	not	possible	when	the	test	pattern	is	displayed.
[OPTIONS(1)]
Setting	Auto	Adjust	[AUTO	ADJUST]
This	feature	 sets	the	Auto	 Adjust	 mode	so	that	 the	computer	 signal	can	be	automatically	 or	manually	 adjusted	for	
noise	and	stability. 	You	can	automatically	make	adjustment	in	two	ways: 	[NORMAL]	and	[FINE].
OFF ������������������������The computer signal will not be automatically adjusted� You can manually optimize the computer signal�
NORMAL ����������������Default setting� The computer signal will be automatically adjusted� Normally select this option�
FINE  �����������������������Select this option if fine adjustment is needed� It takes more time to switch to the source than when [NOR-
MAL]is selected�
Selecting	Fan	Mode	[FAN	MODE]
This	option	allows	you	to	select	three	modes	for	fan	speed: 	Auto	mode,	High	speed	mode,	and	High	Altitude	mode.
AUTO ���������������������The built-in fans automatically run at a variable speed according to the\
 internal temperature�
HIGH ����������������������The built-in fans run at high speed�
HIGH ALTITUDE  �����The built-in fans run at a high speed� Select this option when using the projector at altitudes approximately 
5500 feet/1600 meters or higher �
When	you	wish	to	cool	down	the	temperature	inside	the	projector	quickly,	select	[HIGH].
NOTE:	
•	 It	is	recommended	that	you	select	High	speed	mode	if	you	use	the	projector	non-stop	for	consecutive	days.
•		 Set	[FAN	MODE]	to	[HIGH	ALTITUDE]	when	using	the	projector	at	altitudes	approximately	5500	feet/1600	meters	or	higher.
•	 Using	the	projector	 at	altitudes	 approximately	 5500	feet/1600	 meters	or	higher	 without	 setting	to	[HIGH	 ALTITUDE]	 can	cause	
the	projector	to	overheat	and	the	protector	could	shut	down.	If	this	happens,	wait	a	couple	minutes	and	turn	on	the	projector.
•		 Using	 the	projector	 at	altitudes	 less	than	 approximately	 5500	feet/1600	 meters	and	setting	 to	[HIGH	 ALTITUDE]	 can	cause	 the	
lamp	to	overcool,	causing	the	image	to	flicker.	Switch	[FAN	MODE]	to	[AUTO].
•		 Using	 the	projector	 at	altitudes	 approximately	 5500	feet/1600	 meters	or	higher	 can	shorten	 the	life	of	optical	 components	 such	
as	the	lamp.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu. 
						

							90
5. Using On-Screen Menu
Selecting	Signal	Format	[SIGNAL	SELECT]
[COMPUTER1],	[COMPUTER2]
Allows	you	to	choose	 [COMPUTER1],	 or	[COMPUTER2]	 for	an	RGB	 source	 such	as	a	computer,	 or	[COMPONENT]	
for	 a	component	 video	source	 such	as	a	DVD	 player. 	Normally	 select	[RGB/COMPONENT]	 and	the	projector	 auto-
matically	detects	a	component	 signal.	However	 there	may	be	some	 component	 signals	that	the	projector	 is	unable	 to	
detect.	If	this	is	the	case,	select	[COMPONENT].
[VIDEO	&	S-VIDEO	System	Select]
This	feature	enables	you	to	select	composite	video	standards	automatically	or	manually.
Normally	select	[AUTO]	and	the	projector	will	automatically	detect	the	video	standard.
In	the	 case	 where	 the	projector	 has	difficulty	 detecting	 the	video	 standard,	 select	the	appropriate	 video	standard	 from	
the menu.
This	must	be	done	for	 VIDEO	and	S-VIDEO	respectively.
Enabling	or	Disabling	 WXGA	Mode	[WXGA	MODE]
Selecting	[ON]	will	give	 priority	 to	WXGA	 (1280	×	768)/WUXGA	 (1920	×	1080)	 signals	 in	recognizing	 an	input	 sig-
nal.
When	 [WXGA	 MODE]	is	set	 to	[ON],	 XGA	(1024	 ×	768)/UXGA	 (1600	×	1200)	 signals	 may	not	be	recognized	 on	
M361X/M311X/M271X. 	In	this	case,	select	[OFF].
NOTE:	
•	 The	[OFF]	is	selected	at	the	time	of	shipment	of	M361X/M311X/M271X.
•	 The	[ON]	is	selected	at	the	time	of	shipment	of	M311W/M271W.
Enabling	the	deinterlace	[DEINTERLACE]
Turns	on	or	off	the	deinterlace	function	for	a	telecine	signal.
OFF ������������������������Select this option if there is any jitter or artifacts in video�
ON  �������������������������Default standard setting�
NOTE:	This	feature	is	not	available	for	HDTV	(progressive)	and	computer	signals.
Setting	HDMI	[HDMI	SETTINGS]
Make	the	settings	for	video	level	and	audio	level	when	connecting	HDMI	equipment	such	as	a	DVD	player. 	
VIDEO LEVEL ���������Select [AUTO] to automatically detect video level� If automatic detection may not work well, select [NOR-
MAL] to disable the [ENHANCED] feature of your HDMI equipment or select [ENHANCED] to improve image 
contrast and increase detail in the dark areas�
AUDIO SELECT  ������Select [HDMI] to switch the HDMI IN digital audio signal and select [COMPUTER 2] to switch the COMPUTER 
2 input audio signal�
Enabling	Key	Sound	and	Error	Sound	[BEEP]
This	 feature	 turns	on	or	off	 the	 button	 sound	or	alarm	 when	an	error	 occurs	 or	the	 following	 operations	 are	per-
formed.
-	Displaying	the	main	menu	
-	Switching	sources
-	Resetting	data	by	using	[RESET]
-	Pressing	POWER	ON	or	POWER	OFF	button