NEC M350xs Projector Users Manual

							81
5. Using On-Screen Menu
 Menu Descriptions & Functions [SETUP]
[GENERAL]
[M350X/M300X/M260X/M230X/M300W/M260W/
M420X/M420XV][M350XS/M300XS/M260XS/M300WS/M260WS]
Using	Digital	Zoom	[DIGITAL	ZOOM]	(M350XS/M300XS/M260XS/M300WS/M260WS)	
This	
feature	 allows	you	to	electronically	 fine	adjust	 the	image	 size	on	the	 screen. 	Use	 the	◀ or  ▶	button	 to	large	 or	
reduce	the	projected	image. 	
TIP:	To	adjust	 the	projected	 image	size	roughly,	 move	the	projector	 away	or	closer	 to	the	 screen.	 To	fine	 adjust	 the	zoom,	 use	the	
[DIGITAL	ZOOM]	function.	(→	page	21)
Enabling	Auto	Keystone	[AUTO	KEYSTONE]
This	feature	allows	the	projector	to	detect	its	tilt	and	correct	vertical	distortion	automatically.
To	turn	on	the	AUTO	KEYSTONE	feature,	select	[ON]. 	To	adjust	the	KEYSTONE	feature	manually,	select	[OFF].
NOTE:	 The	[AUTO	 KEYSTONE]	 function	is	not	 available	 when	an	orientation	 type	such	 as	[CEILING	 REAR],	[DESKTOP	 REAR],	
[CEILING	FRONT]	other	than	[DESKTOP/FRONT]	is	selected	for	[ORIENTATION].
TIP:
•	 The	range	of	the	AUTO	KEYSTONE	correction	varies	depending	on	the	model	name.
	 M420X/M420XV/M350X/M300X/M260X/M230X/M300W/M260W:	up	to	30	degrees	(vertical)
	 M350XS/M300XS/M260XS/M300WS/M260WS:	up	to	20	degrees	(vertical)
•	 The	AUTO	KEYSTONE	correction	will	take	effect	in	2	seconds	after	changing	the	projection	angle	during	projection.
Correcting	 Vertical	Keystone	Distortion	Manually	[KEYSTONE]
You	can	correct	vertical	distortion	manually. 	(→	page	24)
TIP:	When	this	option	is	highlighted,	pressing	the	ENTER	button	will	display	its	slide	bar	for	adjustment.
Saving	Vertical	Keystone	Correction	[KEYSTONE	SAVE]
This	option	enables	you	to	save	your	current	keystone	settings.
OFF ������������������������Does  not  save  current  keystone  correction  settings �  It  will  return  your  keystone  correction  settings  to 
“zero”�
ON �������������������������Saves current keystone correction settings
Saving	your	change	once	affects	all	sources. 	The	changes	are	saved	when	the	projector	is	turned	off.
NOTE:	 When	[AUTO	 KEYSTONE]	 is	set	 to	[ON],	 [KEYSTONE	 SAVE]	is	not	 available.	 Next	time	you	turn	 on	the	 power,	 the	AUTO	
KEYSTONE	function	will	work	and	the	data	stored	with	[KEYSTONE	SAVE]	will	be	invalid. 
						

							82
5. Using On-Screen Menu
Using	the	Wall	Color	Correction	[WALL	COLOR]
 
This	function	allows	for	quick	adaptive	color	correction	in	applications	where	the	screen	material	is	not	white.
NOTE:	Selecting	[WHITEBOARD]	reduces	lamp	brightness.
Setting	Eco	Mode	[ECO	MODE]
The	ECO	MODE	increases	lamp	life,	while	lowering	power	consumption	and	cutting	down	on	CO2 emissions. 
Four	brightness	modes	of	the	lamp	can	be	selected: 	[OFF],	[AUTO	ECO],	[ECO1]	and	[ECO2]	modes.	
(→	page	30) 
						

							83
5. Using On-Screen Menu
Setting	Closed	Caption	[CLOSED	CAPTION]
This	option	 sets	several	 closed	caption	 modes	that	allow	 text	to	be	 superimposed	 on	the	 projected	 image	of	Video	
or S-Video.
OFF
 ������������������������This exits the closed caption mode�
CAPTION 1-4 ���������Text is superimposed�
TEXT 1-4 ����������������Text is displayed�
NOTE:
•	 The	closed	caption	is	not	available	under	the	following	conditions:
-	 when	messages	or	menus	are	displayed.
-	 when	an	image	is	magnified,	frozen,	or	muted.
•	 Portions	 of	superimposed	 text	or	closed	 caption	 may	be	truncated.	 If	that	 happens,	 try	to	place	 the	superimposed	 text	or	
closed	caption	within	the	screen.
Using	Off	 Timer	[OFF	 TIMER]
1.	 Select	your	desired	time	between	30	minutes	and	16	hours: 	OFF,	0:30, 	1:00,	2:00,	4:00,	8:00,	12:00, 	16:00.
2.	 Press	the	ENTER	button	on	the	remote	control.
3.	 The	remaining	time	starts	counting	down.
4.	 The	projector	will	turn	off	after	the	countdown	is	complete.
NOTE:
•	 To	cancel	the	preset	time,	set	[OFF]	for	the	preset	time	or	turn	off	the	power.
•	 When	 the	remaining	 time	reaches	 3	minutes	 before	the	projector	 is	turned	 off,	the	[THE	 PROJECTOR	 WILL	TURN	 OFF	WITHIN	 3	
MINUTES]	message	will	be	displayed	on	the	bottom	of	the	screen.
Selecting	Menu	Language	[LANGUAGE]
You	can	choose	one	of	27	languages	for	on-screen	instructions.
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
[MENU]
Selecting	Menu	Color	[COLOR	SELECT]
You	can	choose	between	two	options	for	menu	color: 	COLOR	and	MONOCHROME.
Turning	On	/	Off	Source	Display	[SOURCE	DISPLAY]
This	option	 turns	on	or	off	 input	 name	 display	 such	as	COMPUTER	 1,	COMPUTER2,	 HDMI,	VIDEO,	 S-VIDEO,	
VIEWER,	NETWORK,	USB	DISPLAY,	to	be	displayed	on	the	top	right	of	the	screen.
When	no	input	 signal	 is	present,	 the	no-signal	 guidance	 prompting	 you	to	check	 for	an	available	 input	will	be	displayed	
at	the	 center	 of	the	 screen. 	When	 the	[VIEWER]	 or	[NETWORK]	 item	is	selected	 for	[SOURCE],	 the	no-signal	 guid-
ance	will	not	be	displayed. 
						

							84
5. Using On-Screen Menu
Turning	ON/OFF	Control	ID	[ID	DISPLAY]
ID DISPLAY �����������This option turns on or off the ID number which is displayed when the ID SET button on the remote control 
is pressed�
Turning	On	/	Off	Eco	Message	[ECO	MESSAGE]
This	option	turns	on	or	off	the	following	messages	when	the	projector	is	turned	on. 	
The	Eco	Message	 prompts	the	user	 to	save	 energy. 	When	 [OFF]	is	selected	 for	[ECO	 MODE],	 you	will	get	 a	message	
to	prompt	you	to	select	[AUTO	ECO],	[ECO1],	or	[ECO2]*	for	[ECO	MODE].
When	[AUTO	ECO],	[ECO1],	or	[ECO2]*	is	selected	for	[ECO	MODE]
NOTE:	*	[ECO2]	is	available	on	M300X,	M260X,	M300XS,	M260XS,	and	M260WS	only.	
To	 close	 the	message,	 press	any	one	 of	the	 buttons. 	The	 message	 will	disappear	 if	no	 button	 operation	 is	done	 for	
30 seconds.
When	[OFF]	is	selected	for	[ECO	MODE]
Pressing	the	ENTER	button	will	display	the	[ECO	MODE]	screen. 	(→	page	30)
To	close	the	message,	press	the	EXIT	button.
Selecting	Menu	Display	Time	[DISPLAY	TIME]
This	option	 allows	 you	to	select	 how	long	 the	projector	 waits	after	the	last	 touch	 of	a	button	 to	turn	 off	the	 menu. 	The	
preset	 choices	 are	[MANUAL],	 [AUTO	5	SEC],	 [AUTO	 15	SEC],	 and	[AUTO	 45	SEC]. 	The	 [AUTO	 45	SEC]	 is	the	 fac-
tory	preset.
Selecting	a	Color	or	Logo	for	Background	[BACKGROUND]
Use 	this 	feature 	to 	display 	a 	blue/black 	screen 	or 	logo 	when 	no 	signal 	is 	available. 	The 	default 	background 	is	
[BLUE].
NOTE: 
•	 If	 the	[LOGO]	 item	is	selected	 for	[BACKGROUND]	 with	the	[NETWORK]	 or	[USB	 DISPLAY]	 source	selected,	 the	[BLUE]	 item	will	
be	selected	regardless	of	its	selection.
•	 When	 [SOURCE	 DISPLAY]	 is	turned	 on,	the	no-signal	 guidance	prompting	 you	to	check	 for	an	available	 input	will	be	displayed	
at	the	center	of	the	screen	regardless	of	its	selection.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Selecting	Interval	 Time	for	Filter	Message	[FILTER	MESSAGE]
This	option	 allows	 you	to	select	 the	time	 preference	 between	displaying	 the	message	 for	cleaning	 the	filters. 	Clean	
the	filter	when	you	get	the	message	 “PLEASE	CLEAN	FILTER.”	(→	page	115)
Five	options	are	available:	OFF,	100[H],	500[H],	1000[H],	2000[H]
The	default	setting	is	[OFF].
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu. 
						

							85
5. Using On-Screen Menu
[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	 your	image	 for	your	 type	of	projection. 	The	 options	 are:	desktop	 front	projection,	 ceiling	rear	projection,	
desktop	rear	projection,	and	ceiling	front	projection.
DESKTOP	FRONTCEILING	REAR
DESKTOP	REARCEILING	FRONT
Disabling	the	Cabinet	Buttons	[CONTROL	PANEL	LOCK]
This	option	turns	on	or	off	the	CONTROL	PANEL	LOCK	function.
NOTE:
•	 This	CONTROL	PANEL	LOCK	does	not	affect	the	remote	control	functions.
•	 When	 the	control	 panel	is	locked,	 pressing	 and	holding	 the	EXIT	 button	 on	the	 projector	 cabinet	for	about	 10	seconds	 will	change	
the	setting	to	[OFF].
TIP:	When	the	[CONTROL	PANEL	LOCK]	is	turned	on,	a	key	lock	icon	[		]	will	be	displayed	at	the	bottom	right	of	the	menu.
Enabling	Security	[SECURITY]
This	feature	turns	on	or	off	the	SECURITY	function.
Unless	the	correct	keyword	is	entered,	the	projector	cannot	project	an	image. 	(→	page	32)
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu. 
						

							86
5. Using On-Screen Menu
Selecting	Communication	Speed	[COMMUNICATION	SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	38400	 bps.	The	
default	 is	38400	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	 equip-
ment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE:	Your	selected	communication	speed	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Setting	ID	to	the	Projector	[CONTROL	ID]
You	can 	operate 	multiple 	projectors 	separately 	and 	independently 	with 	the 	single 	remote 	control 	that 	has 	the 	CONTROL	
ID	 function. 	If	 you	 assign	 the	same	 ID	to	all	 the	 projectors,	 you	can	 conveniently	 operate	all	the	 projectors	 together	
using	the	single	remote	control. 	To	do	so,	you	have	to	assign	an	ID	number	to	each	projector.
CONTROL ID NUMBER �������Select a number from 1 to 254 you wish to assign to your projector �
CONTROL ID �����������������������Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set -
ting�
NOTE: 
•	 When	[ON]	is	selected	 for	[CONTROL	 ID],	the	projector	 cannot	be	operated	 by	using	 the	remote	 control	that	does	 not	support	
the	CONTROL	ID	function.	(In	this	case	the	buttons	on	the	projector	cabinet	can	be	used.)
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
•		 Pressing	 and	holding	 the	ENTER	 button	on	the	 projector	 cabinet	for	10	seconds	 will	display	 the	menu	 for	canceling	 the	Control	
ID.
Assigning	or	Changing	the	Control	ID
1.	 Turn	on	the	projector.
2.	 Press	the	ID	SET	button	on	the	remote	control.
 The CONTROL ID screen will be displayed.
 If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed. If the projector 
cannot be operated with the current remote control ID, the [INACTIVE] will be displayed. To operate the inactive 
projector, assign the control ID used for the projector by using the following procedure (Step 3).
3.	 Press	 one	of	numeric	 keypad	buttons	 while	pressing	 and	holding	 the	ID	SET	
button	on	the	remote	control.
 Example:
 To assign “3”, press the “3” button on the remote control.
 No  ID  means  that  all  the  projectors  can  be  operated  together  with  a  single  remote 
control. To set “No ID”, enter “000” or press the CLEAR button.
TIP:	The	range	of	IDs	is	from	1	to	254.
4.	 Release	the	ID	SET	button.
 The updated CONTROL ID screen will be displayed.
NOTE: 
•		 The	IDs	can	be	cleared	in	a	few	days	after	the	batteries	are	run	down	or	removed.
•		 Accidentally	 pressing	any	one	 of	the	 buttons	 of	the	 remote	 control	will	clear	 currently	 specified	
ID	with	batteries	removed. 
						

							87
5. Using On-Screen Menu
Using	Test	Pattern	[TEST	PATTERN]
Displays	 the	test	 pattern	 to	check	 for	image	 distortion	 at	the	 time	 of	the	 projector	 setup.	Press	 the	ENTER	 button	to	
display	 the	test	 pattern; 	press	 the	EXIT	 button	 to	close	 the	test	 pattern	 and	return	 to	the	 menu. 	Menu	 operation	 and	
keystone	correction	are	not	possible	when	the	test	pattern	is	displayed.
[OPTIONS(1)]
[M350X/M300X/M260X/M230X/M300W/M260W/
M420X/M350XS/M300XS/M260XS/M300WS/
M260WS] [M420XV]
Setting	Auto	Adjust	[AUTO	ADJUST]
This	
feature	 sets	the	Auto	 Adjust	 mode	so	that	 the	computer	 signal	can	be	automatically	 or	manually	 adjusted	for	
noise	and	stability. 	You	can	automatically	make	adjustment	in	two	ways: 	[NORMAL]	and	[FINE].
OFF ������������������������The computer signal will not be automatically adjusted� You can manually optimize the computer signal�
NORMAL ����������������Default setting� The computer signal will be automatically adjusted� Normally select this option�
FINE  �����������������������Select this option if fine adjustment is needed� It takes more time to switch to the source than when [NOR-
MAL]is selected�
Selecting	Fan	Mode	[FAN	MODE]
This	option	allows	you	to	select	three	modes	for	fan	speed: 	Auto	mode,	High	speed	mode,	and	High	Altitude	mode.
AUTO ���������������������The built-in fans automatically run at a variable speed according to the\
 internal temperature�
HIGH ����������������������The built-in fans run at high speed�
HIGH ALTITUDE  �����The built-in fans run at a high speed� Select this option when using the projector at altitudes approximately 
5500 feet/1600 meters or higher �
When	you	wish	to	cool	down	the	temperature	inside	the	projector	quickly,	select	[HIGH].
NOTE: 
•	 It	is	recommended	that	you	select	High	speed	mode	if	you	use	the	projector	non-stop	for	consecutive	days.
•		 Set	[FAN	MODE]	to	[HIGH	ALTITUDE]	when	using	the	projector	at	altitudes	approximately	5500	feet/1600	meters	or	higher.
•	 Using	the	projector	 at	altitudes	 approximately	 5500	feet/1600	 meters	or	higher	 without	 setting	to	[HIGH	 ALTITUDE]	 can	cause	
the	projector	to	overheat	and	the	protector	could	shut	down.	If	this	happens,	wait	a	couple	minutes	and	turn	on	the	projector.
•		 Using	 the	projector	 at	altitudes	 less	than	 approximately	 5500	feet/1600	 meters	and	setting	 to	[HIGH	 ALTITUDE]	 can	cause	 the	
lamp	to	overcool,	causing	the	image	to	flicker.	Switch	[FAN	MODE]	to	[AUTO].
•		 Using	 the	projector	 at	altitudes	 approximately	 5500	feet/1600	 meters	or	higher	 can	shorten	 the	life	of	optical	 components	 such	
as	the	lamp.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu. 
						

							88
5. Using On-Screen Menu
Selecting	Signal	Format	[SIGNAL	SELECT]
[COMPUTER1],	[COMPUTER2]
Allows	you	to	choose	 [COMPUTER1],	 or	[COMPUTER2]	 for	an	RGB	 source	 such	as	a	computer,	 or	[COMPONENT]	
for	 a	component	 video	source	 such	as	a	DVD	 player. 	Normally	 select	[RGB/COMPONENT]	 and	the	projector	 auto-
matically	detects	a	component	 signal.	However	 there	may	be	some	 component	 signals	that	the	projector	 is	unable	 to	
detect.	If	this	is	the	case,	select	[COMPONENT].
[VIDEO	&	S-VIDEO	System	Select]
This	feature	enables	you	to	select	composite	video	standards	automatically	or	manually.
Normally	select	[AUTO]	and	the	projector	will	automatically	detect	the	video	standard.
In	the	 case	 where	 the	projector	 has	difficulty	 detecting	 the	video	 standard,	 select	the	appropriate	 video	standard	 from	
the menu.
This	must	be	done	for	 VIDEO	and	S-VIDEO	respectively.
Enabling	or	Disabling	 WXGA	Mode	[WXGA	MODE]
Selecting	[ON]	will	give	priority	to	a	 WXGA	(1280	×	768)	signal	in	recognizing	an	input	signal.
When	[WXGA	 MODE]	is	set	 to	[ON],	 an	XGA	 (1024	 ×	768)	 signal	 may	not	be	recognized	 on	M350X/M300X/M260X/
M230X/M420X/M420XV/M350XS/M300XS/M260XS. 	In	this	case,	select	[OFF].
NOTE: 
•	 The	[OFF]	is	selected	at	the	time	of	shipment	of	M350X/M300X/M260X/M230X/M420X/M420XV/M350XS/M300XS/M260XS.
•	 The	[ON]	is	selected	at	the	time	of	shipment	of	M300W/M260W/M300WS/M260WS.
Enabling	the	deinterlace	[DEINTERLACE]
Turns	on	or	off	the	deinterlace	function	for	a	telecine	signal.
OFF ������������������������Select this option if there is any jitter or artifacts in video�
ON  �������������������������Default standard setting�
NOTE:	This	feature	is	not	available	for	HDTV	(progressive)	and	computer	signals.
Setting	HDMI	[HDMI	SETTINGS]
Make	the	settings	for	video	level	and	audio	level	when	connecting	HDMI	equipment	such	as	a	DVD	player. 	
VIDEO LEVEL ���������Select [AUTO] to automatically detect video level� If automatic detection may not work well, select [NOR-
MAL] to disable the [ENHANCED] feature of your HDMI equipment or select [ENHANCED] to improve image 
contrast and increase detail in the dark areas�
AUDIO SELECT (not available on M420XV)
  ������������������������������Select [HDMI] to switch the HDMI IN digital audio signal and select [COMPUTER 2] to switch the COMPUTER 
2 input audio signal�
Enabling	Key	Sound	and	Error	Sound	[BEEP]	(not	available	on	M420XV)
This	 feature	 turns	on	or	off	 the	 button	 sound	or	alarm	 when	an	error	 occurs	 or	the	 following	 operations	 are	per-
formed.
-	Displaying	the	main	menu	
-	Switching	sources
-	Resetting	data	by	using	[RESET]
-	Pressing	POWER	ON	or	POWER	OFF	button 
						

							89
5. Using On-Screen Menu
[OPTIONS(2)]
Selecting	Power-saving	in	[STANDBY	MODE]
The	projector	has	two	standby	modes:	[NORMAL]	and	[POWER-SAVING].
The	POWER-SAVING	 mode	is	the	 mode	 that	allows	 you	to	put	 the	projector	 in	the	 power-saving	 condition	which	
consumes	less	power	than	the	NORMAL	mode. 	The	projector	is	preset	for	NORMAL	mode	at	the	factory.
NORMAL ����������������Power indicator: Orange light/STATUS indicator: Green light
POWER-SAVING
  ����Power indicator: Red light/STATUS indicator: Off
The following connectors, buttons or functions will not work during this\
 mode�
-   MONITOR OUT (COMP � 1) connector, and AUDIO OUT connector (The M420XV does not come with the 
AUDIO OUT connector�)
- LAN and Mail Alert functions
- Buttons other than POWER button on the cabinet
- Buttons other than POWER ON button on the remote control
- Virtual Remote Tool, USB Display fucntion
NOTE: 
•	 When	 [CONTROL	 PANEL	LOCK],	 [CONTROL	 ID],	or	[AUTO	 POWER	 ON(COMP1)]	 is	turned	 on,	the	[STANDBY	 MODE]	setting	is	
not	available.
•	 Even	when	[POWER-SAVING]	is	selected	for	[STANDBY	MODE],	power	on	or	off	can	be	done	by	using	the	PC	CONTROL	port.
•	 The	power	consumption	in	the	standby	mode	will	not	be	included	in	calculating	CO2	emission	reduction.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Enabling	Auto	Power	On	[AUTO	POWER	ON(AC)]
Turns	the	projector	 on	automatically	 when	the	power	 cord	is	inserted	 into	an	active	 power	 outlet.	This	 eliminates	 the	
need	to	always	use	the	POWER	button	on	the	remote	control	or	projector	cabinet. 
						

							90
5. Using On-Screen Menu
Turning	On	the	Projector	By	Applying	Computer	Signal	[AUTO	POWER	ON(COMP1)]
When	the	projector	 is	in	 Standby	 mode,	applying	 a	computer	 signal	from	a	computer	 connected	 to	the	 COMPUTER1	
IN	input	will	power	on	the	projector	and	simultaneously	project	the	computer’s	image.
This	 functionality	 eliminates	the	need	 to	always	 use	the	POWER	 button	on	the	 remote	 control	or	the	 projector	 cabinet	
to	power	on	the	projector.
To	use	this	function,	first	connect	a	computer	to	the	projector	and	the	projector	to	an	active	AC	input.
NOTE: 
•	 Disconnecting	 a	computer	 signal	from	the	computer	 will	not	power	 off	the	 projector.	 We	recommend	 using	this	function	 in	com-
bination	of	the	AUTO	POWER	OFF	function.
•	 This	function	will	not	be	available	under	the	following	conditions:
-	 when	a	component	signal	is	applied	to	the	COMPUTER1	IN	connector
-	 when	a	Sync	on	Green	RGB	signal	or	composite	sync	signal	is	applied
•	 To	enable	the	AUTO	POWER	ON	(COMP1)	after	turning	off	the	projector,	wait	3	seconds	and	input	a	computer	signal.
	 If	 a	computer	 signal	is	still	 present	 when	the	projector	 is	turned	 off,	the	AUTO	 POWER	 ON	(COMP1)	 will	not	work	 and	the	projector	
remains	in	standby	mode.
Enabling	Power	Management	[AUTO	POWER	OFF]
When	 this	option	 is	selected	 you	can	 enable	 the	projector	 to	automatically	 turn	off	(at	 the	 selected	 time:	5min.,	 10min.,	
20min.,	30min.)	if	there	is	no	signal	received	by	any	input	or	if	no	operation	is	performed.
Selecting	Default	Source	[DEFAULT	SOURCE	SELECT]
You	can	set	the	projector	to	default	to	any	one	of	its	inputs	each	time	the	projector	is	turned	on.
LAST ����������������������Sets the projector to default to the previous or last active input each \
time the projector is turned on�
AUTO  ���������������������Searches for an active source in order of COMPUTER1  → COMPUTER2 → HDMI → VIDEO  → S-VIDEO  → 
VIEWER → USB DISPLAY →
 COMPUTER1 and displays the first found source�
COMPUTER1  ���������Displays the computer signal from the COMPUTER 1 IN connector every time the projector is turned on�
COMPUTER2 ���������Displays the computer signal from the COMPUTER 2 IN connector every time the projector is turned on�
HDMI ���������������������Displays the digital source from the HDMI IN connector every time the projector is turned on� 
VIDEO ��������������������Displays the Video source from the VIDEO IN connector every time the projector is turned on�
S-VIDEO  ����������������Displays the Video source from the S-VIDEO IN connector every time the projector is turned on�
VIEWER �����������������Displays slides or plays back movie files from the USB memory device every time the projector is turned 
on�
NETWORK  �������������Displays a signal from LAN port (RJ-45) or the USB Wireless LAN Unit�
USB DISPLAY ��������Displays the computer signal from the USB (PC) port every time the projector is turned on�