NEC M332xs Projector Users Manual

							130
7. Maintenance
This completes the lamp replacement.
Go on to the clearing lamp hour meters. 
NOTE:	When	you	continue	 to	use	 the	projector	 for	another	 100	hours	 after	the	lamp	 has	reached	 the	end	 of	its	 life,	 the	projector	
cannot	turn	on	and	the	menu	is	not	displayed.
If	this	happens,	press	the	HELP	button	on	the	remote	control	for	10	seconds	to	reset	the	lamp	clock	back	to	zero.
When	the	lamp	time	clock	is	reset	to	zero,	the	LAMP	indicator	goes	out. 	
To clear the lamp usage hours:
1.	 Place	the	projector	where	you	use	it.
2.	 Plug	the	power	cord	into	the	wall	outlet,
	and	then	turn	on	the	projector.
3.	 Clear	the	lamp	usage	hours.
From the menu, select [RESET] → [CLEAR LAMP HOURS] and reset the lamp usage hours.
4. Reattach the lamp cover.
(1)	Slide	the	lamp	cover	back	until	it	snaps	into	place.
(2)	Tighten	the	screw	to	secure	the	lamp	cover.
	 •	Be	sure	to	tighten	the	screw.
3.	 Install	a	new	lamp	housing.
(1)	Insert	a	new	lamp	housing	until	the	lamp	housing	is	plugged	into	the	socket. 	
(2)	Push	the	top	center	of	the	lamp	housing	to	secure	it.
(3)	Secure	it	in	place	with	the	three	screws.
	 •	Be	sure	to	tighten	the	screws. 
						

							131
8. Appendix
❶ Troubleshooting
This	section	helps	you	resolve	problems	you	may	encounter	while	setting	up	or	using	the	projector.
Indicator Messages
Power Indicator
Indicator ConditionProjector	ConditionNote
Off The main power is off –
Blinking light Blue
0�5 sec On,0�5 sec OffThe projector is getting ready to turn on�Wait for a moment�
2�5 sec On,0�5 sec OffOff Timer is enabled� –
Steady lightBlueThe projector is turned on�–
Orange The projector is [NETWORK STANDBY] mode or 
sleep mode*�–
Red [NORMAL] is selected for [STANDBY MODE] –
Status Indicator
Indicator ConditionProjector	ConditionNote
Off Power on or Standby ([NORMAL] or [NETWORK 
STANDBY] for [STANDBY MODE]) –
Blinking light Red
1  cycle  (0�5  sec On, 2�5 sec Off)Lamp cover error or lamp housing errorReplace the lamp cover or lamp housing correctly �
2  cycle  (0�5  sec On, 0�5 sec Off)Temperature errorThe projector is overheated� Move the projector to a cooler location�3  cycle  (0 �5  sec On, 0�5 sec Off)Power errorPower  unit  is  not  working  properly �  Contact  your dealer�4  cycle  (0 �5  sec On, 0�5 sec Off)Fan errorFans will not work correctly �
6  cycle  (0�5  sec On, 0�5 sec Off)Lamp errorLamp fails to light� Wait a full minute and then turn on again�Orange1  cycle  (0 �5  sec On, 2�5 sec Off)Network conflict Both the built-in wired LAN and the wireless LAN cannot be connected to the same network at the same time�To use both built-in wired LAN and wireless LAN at the same time, connect them to different networks�Green Re-firing  the  lamp  (The  projector  is  cooling down�)The projector is re-firing�Wait for a moment�Steady	lightGreen
The  projector  is  in  [NORMAL]  mode  or  sleep mode�–
Orange
CONTROL PANEL LOCK is on�You  have  pressed  cabinet  button  when  Control Panel Lock is on�CONTROL ID error R e m o t e   c o n t r o l   I D   a n d   p r o j e c t o r   I D   a r e   n o t matched�
Lamp Indicator
Indicator ConditionProjector	ConditionNote
Off Normal –
Blinking light Red
Lamp  has  reached  its  end  of  life�  Lamp  replace-ment message will be displayed�Replace the lamp�
Steady lightRedLamp has been used beyond its limit � The projector will not turn on until the lamp is replaced�Replace the lamp�
Green
[ECO  MODE]  is  set  to  [AUTO  ECO],  [NORMAL] 
or [ECO] –
*	For	more	information	on	"sleep	mode",	see	page	119.
Over-Temperature	Protection
If	
the	 temperature	 inside	the	projector	 rises	too	high,	 the	over-temperature	 protector	will	automatically	 turn	off	the	 lamp	
with	the	STATUS	indicator	blinking	(2-cycle	On	and	Off.)
Should	this	happen,	do	the	following:
•	 Unplug	the	power	cord	after	the	cooling	fans	stop.
•	 Move	the	projector	to	a	cooler	location	if	the	room	where	you	are	presenting	is	particularly	too	warm.
•	 Clean	the	vents	if	they	are	clogged	with	dust.
•	 Wait	about	60	minutes	until	the	inside	of	the	projector	becomes	cool	enough. 
						

							132
8. Appendix
Common Problems & Solutions
(→	“Power/Status/Lamp	Indicator” 	on	page	131.)
ProblemCheck	These	Items
Does not turn on
or shut down•	 Check	 that	the	power	 cord	is	plugged	 in	and	 that	 the	power	 button	 on	the	 projector	 cabinet	or	the	 remote	 control	is on� (→ pages 16, 17)•	 Ensure	that	the	lamp	cover	is	installed	correctly.	(→ page 130)•	 Check	 to	see	 if	the	 projector	 has	overheated.	 If	there	 is	insufficient	 ventilation	around	the	projector	 or	if	the	 room	where you are presenting is particularly warm, move the projector to a c\
ooler location�•	 Check	 to	see	 if	you	 continue	 to	use	 the	projector	 for	another	 100	hours	 after	the	lamp	 has	reached	 the	end	 of	its	life� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� (→ page 113)•	 The	lamp	may	fail	to	light.	Wait	a	full	minute	and	then	turn	on	the	power	again.•	 Set	 [FAN	MODE]	 to	[HIGH	 ALTITUDE]	 when	using	 the	projector	 at	altitudes	 approximately	 5500	feet/1700	 meters	or higher� Using the projector at altitudes approximately 5500 feet/1700 meters or higher without setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a couple minutes and turn on the projector � (→ page 99) If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for some time and then the projector will display the image� Wait for a moment�
Will turn off•	 Ensure	that	the	[OFF	TIMER]	or	[AUTO	POWER	OFF]	is	off.	(→ page 94, 102)
No picture
•	 Use	 the	input	 select	 button	 on	the	 remote	 control	to	select	 your	source	 (COMPUTER,	 HDMI1,	HDMI2,	VIDEO,	USB-A, LAN, or USB-B)� (→ page 19) If there is still no picture, press the button again�•	 Ensure	your	cables	are	connected	properly.•	 Use	menus	to	adjust	the	brightness	and	contrast.	(→ page 86)•	 Ensure	that	the	lens	cap	is	removed.	(→ page 5,17)•	 Reset	the	settings	or	adjustments	to	factory	preset	levels	using	the	[RESET]	in	the	Menu.	(→ page 113)•	 Enter	your	registered	keyword	if	the	Security	function	is	enabled.	(→ page 33)•	 Be	sure	to	connect	 the	projector	 and	notebook	 PC	while	 the	projector	 is	in	 standby	 mode	and	before	 turning	 on	the power to the notebook PC� In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up�* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software�•	 See	also	the	next page�
Picture  suddenly  be -
comes dark•	 Check	 if	the	 projector	 is	in	 the	 Forced	 ECO	mode	 because	 of	too	 high	 ambient	 temperature.	 If	this	 is	the	 case,	lower the internal temperature of the projector by selecting [HIGH] for \
[FAN MODE]� (→ page 99)
Color tone or hue is un -
usual
•	 Check	if	an	appropriate	color	is	selected	in	[WALL	COLOR].	If	so,	select	an	appropriate	option.	(→ page 93)•	 Adjust	[HUE]	in	[PICTURE].	(→ page 86)
Image isn’t square to the 
screen
•	 Reposition	the	projector	to	improve	its	angle	to	the	screen.	(→ page 20)•	 Use	the	Keystone	correction	function	to	correct	the	trapezoid	distortion.	(→ page 24)
Picture is blurred
•	 Adjust	the	focus.	(→ page 23)•	 Reposition	the	projector	to	improve	its	angle	to	the	screen.	(→ page 20)•	 Ensure 	that 	the 	distance 	between 	the 	projector 	and 	screen 	is 	within 	the 	adjustment 	range 	of 	the 	lens. 
(→ page 114)
•	 Condensation	 may	form	 on	the	 lens	 if	the	 projector	 is	cold,	 brought	 into	a	warm	 place	and	is	then	 turned	 on.	Should this happen, let the projector stand until there is no condensati\
on on the lens�
F l i c k e r   a p p e a r s   o n 
screen •	Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1700 meters or lower
� Using the projector at altitudes less than approximately 5500 feet/1700 meters and setting to [HIGH ALTI-TUDE] can cause the lamp to overcool, causing the image to flicker � Switch [FAN MODE] to [AUTO]� (→ page 9 9)
Image  is  scrolling  ver -
tically,  horizontally  or 
both•	 Check 	the 	computer’s 	resolution 	and 	frequency. 	Make 	sure 	that 	the 	resolution 	you 	are 	trying 	to 	display 	is 	supported	by the projector � (→ page 138)•	 Adjust	the	computer	image	manually	with	the	Horizontal/Vertical	in	the	[IMAGE	OPTIONS].	(→ page 88)
R e m o t e   c o n t r o l   d o e s 
not work
•	 Install	new	batteries.(→ page 11)•	 Make	sure	there	are	no	obstacles	between	you	and	the	projector.•	 Stand	within	22	feet	(7	m)	of	the	projector.	(→ page 11)
Indicator  is  lit  or  blink -
ing
•	 See	the	POWER/STATUS/LAMP	Indicator.	(→ page 131)
C r o s s   c o l o r   i n   R G B 
mode
•	 Press	the	AUTO	ADJ.	button	on	the	projector	cabinet	or	the	remote	control.	(→ page 26)•	 Adjust	the	computer	image	manually	with	[CLOCK]/[PHASE]	in	[IMAGE	OPTIONS]	in	the	menu.	(→ page 87)
For	more	information	contact	your	dealer. 
						

							133
8. Appendix
If there is no picture, or the picture is not displayed correctly.
•	 Power	on	process	for	the	projector	and	the	PC.
	 Be	sure	to	connect	 the	projector	 and	notebook	 PC	while	 the	projector	 is	in	 standby	 mode	and	before	 turning	 on	
the	power	to	the	notebook	PC.
	 In	most	cases	 the	output	 signal	from	the	notebook	 PC	is	not	 turned	 on	unless	 connected	 to	the	 projector	 before	
being	powered	up.
NOTE:	You	can	check	 the	horizontal	 frequency	of	the	 current	 signal	in	the	 projector’s	 menu	under	 Information.	 If	it	reads	 “0kHz”,	
this	means	there	is	no	signal	being	output	from	the	computer.	(→	page	110	or	go	to	next	step)
•	 Enabling	the	computer’s	external	display.
	 Displaying	 an	image	 on	the	 notebook	 PC’s	screen	 does	not	necessarily	 mean	it	outputs	 a	signal	 to	the	 projector. 	
When	using	a	PC	 compatible	 laptop,	a	combination	 of	function	 keys	will	enable/disable	 the	external	 display.	Usu-
ally,	 the	combination	 of	the	 “Fn” 	key	 along	 with	one	of	the	 12	function	 keys	gets	the	external	 display	to	come	 on	
or	off. 	For	 example,	 NEC	laptops	 use	Fn	+	F3,	 while	 Dell	laptops	 use	Fn	+	F8	 key	 combinations	 to	toggle	 through	
external	display	selections.
•	 Non-standard	signal	output	from	the	computer
	 If	the	output	 signal	from	a	notebook	 PC	is	not	 an	industry	 standard,	 the	projected	 image	may	not	be	displayed	
correctly. 	Should	 this	happen,	 deactivate	 the	notebook	 PC’s	LCD	screen	 when	the	projector	 display	is	in	 use. 	Each	
notebook	 PC	has	 a	different	 way	of	deactivate/reactivate	 the	local	 LCD	screens	 as	described	 in	the	 previous	 step.	
Refer	to	your	computer’s	documentation	for	detailed	information.
•	 Image	displayed	is	incorrect	when	using	a	Mac
	 When	 using	a	Mac	 with	the	projector,	 set	the	 DIPswitch	 of	the	 Mac	 adapter	 (not	supplied	 with	the	projector)	 ac-
cording	to	your	resolution. 	After	setting,	restart	your	Mac	for	the	changes	to	take	affect.
	 For	setting	display	 modes	other	than	those	 supported	 by	your	 Mac	and	the	projector,	 changing	the	DIP	 switch	 on	
a	Mac	 adapter	 may	bounce	 an	image	 slightly	 or	may	 display	 nothing. 	Should	 this	happen,	 set	the	 DIP	 switch	 to	
the	13"	 fixed	 mode	 and	then	 restart	 your	Mac.	After	 that,	restore	 the	DIP	 switches	 to	a	displayable	 mode	and	then	
restart	the	Mac	again.
NOTE:	 A	Video	 Adapter	 cable	manufactured	 by	Apple	 Inc.	is	needed	 for	a	MacBook	 which	does	not	have	 a	mini	 D-Sub	 15-pin	
connector.
•	 Mirroring	on	a	MacBook
*	 When	 using	the	projector	 with	a	MacBook,	 output	may	not	be	set	 to	1024	 ×	768	 unless	 “mirroring” 	is	 off	 on	your	
MacBook. 	Refer	to	owner’s	manual	supplied	with	your	Mac	computer	for	mirroring.
•	 Folders	or	icons	are	hidden	on	the	Mac	screen
	 Folders	 or	icons	 may	not	be	seen	 on	the	 screen. 	Should	 this	happen,	 select	[View]	→	[Arrange]	 from	the	Apple	
menu	and	arrange	icons. 
						

							134
8. Appendix
❷ Specifications
This	section	provides	technical	information	about	projector’s	performance.
[M352WS/M302WS/M332XS]
Optical
Model	NumberNP-M352WSNP-M302WS NP-M332XSProjection	SystemSingle	DLP®	chip	(0.65",	aspect	16:10)Single	DLP®	chip	(0.55",	aspect	4:3)
Resolution*11280	×	800	pixels	(WXGA)1024	×	768	pixels	(XGA)LensDigital	zoom	and	manual	focusDigital	Zoom	Ratio	=	1.2F2.4/	f=6.5	mmLamp270	 W	AC	(219	 W	in	NORMAL)(162	W	in	ECO)
225	W	AC	(171	 W	in	NORMAL)(135	W	in	ECO)
270	W	AC	(219	 W	in	NORMAL)(162	W	in	ECO)Light	Output*2*33500 lumens 3000 lumens3300 lumens NORMAL:	81%NORMAL:	76%NORMAL:	81%ECO:	60%*4
Contrast	Ratio*3
(full	white: 	full	black)10000:1	with	DYNAMIC	CONTRAST	ON
Image	Size	(Diagonal)60–150	inches/1.52	m–3.81	m	(16:10)60–150	inches/1.52	m–3.81	m	(4:3)Projection	Distance(Min.–Max.)22.2–58.3	inches/0.57–1.48	m26.6–69.2	inches/0.68–1.76	m	
Projection	Angle40.7°–40.9° 40.7°–40.8°
*1	 Effective	pixels	are	more	than	99.99%.*2	 This	is	the	 light	 output	 value	(lumens)	 when	the	[PRESET]	 mode	is	set	 to	[HIGH-BRIGHT]. 	If	 any	 other	 mode	 is	selected	 as	the	[PRESET]	mode,	the	light	output	value	may	drop	slightly.*3	 Compliance	with	ISO21118-2005*4	The	maximum	power	becomes	equivalent	to	power	in	ECO	(ECO	MODE).
Electrical
Model	NumberNP-M352WS NP-M302WS NP-M332XS
Inputs1	×	RGB/Component	(D-Sub	15	P),	2	×	HDMI	 Type	A	(19P,	HDMI®	Connector)	HDCP	supported*5, 1	×	Video	(RCA),	1	×	(L/R)	RCA	Audio,	1	×	Stereo	Mini	AudioOutputs1	×	RGB	(D-Sub	15P),	1	×	Stereo	Mini	AudioPC	Control1	×	PC	Control	Port	(D-Sub	9P)Wired	LAN	Port1	×	RJ-45	(10BASE-T/100BASE-TX)Wireless	LAN	Port	 
(Optional)IEEE	802.11	b/g/n	(optional	USB	 Wireless	LAN	Unit		required)
USB	Port1	×	Type	A,	1	×	 Type	BMIC	Input1	×	Monaural	Mini	AudioColor	Reproduction10-bit	signal	processing	(1.07	billion	colors)	(USB-A,	LAN: 	16.7	million	colors)
*5	 HDMI®	(Deep	Color,	Lip	Sync)	with	HDCP	 What	is	HDCP/HDCP	technology?	 HDCP	is 	an 	acronym 	for 	High-bandwidth 	Digital 	Content 	Protection. 	High 	bandwidth 	Digital 	Content 	Protection 	(HDCP) 	is 	a 	system	for	preventing	illegal	copying	of	video	data	sent	over	a	High-Definition	Multimedia	Interface	(HDMI).	 If	 you	are	unable	 to	view	 material	 via	the	 HDMI	 input,	this	does	 not	necessarily	 mean	the	projector	 is	not	 functioning	 properly.	With	the	 implementation	 of	HDCP,	 there	may	be	cases	 in	which	 certain	 content	 is	protected	 with	HDCP	 and	might	 not	be	displayed	due	to	the	decision/intention	of	the	HDCP	community	(Digital	Content	Protection,	LLC).	 Video: 	Deep	Color; 	8/10/12-bit,	LipSync	 Audio:	LPCM;	up	to	2	ch,	sample	rate	32/44.1/48	KHz,	sample	bit; 	16/20/24-bit*6	 An	image	 with	higher	 or	lower	 resolution	 than	the	projector’s	 native	resolution	 (M332XS:	1024	 ×	768	 /	M352WS/M302WS: 	1280	×	800)	will	be	displayed	with	Advanced	AccuBlend. 
						

							135
8. Appendix
Model	NumberNP-M352WSNP-M302WS NP-M332XSCompatible	Signals*6Analog:	VGA/SVGA/XGA/WXGA/Quad-VGA/SXGA/SXGA+/WXGA+/WXGA++/UXGA/WSXGA+/HD/Full	HD/WUXGA/Mac13"/Mac16"/Mac	19"/Mac	21"/Mac	23"	Component: 	480i/480p/720p/1080i	(60Hz),	576i/576p/1080i	(50Hz),	DVD	Progressive	(50/60Hz)Digital:	VGA/SVGA/XGA/WXGA/Quad-VGA/SXGA/SXGA+/WXGA+/WXGA++/WSXGA+/HDTV	(1080p)/HDTV	(1080i)/HDTV	(720p)/HDTV	(480p)3D: 	For	PC	XGA/1280	×	720/WXGA,	For	 Video	SDTV	(480i),	For	HDMI-1.4a	720p	(Frame	Packing)/ 1080p	(Frame	Packing)/1080i	(Side	by	Side	(Half))/720p	(Top	and	Bottom)/1080p	(Top	and	Bottom)Horizontal	Resolution540	TV	lines: 	NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60300	TV	lines: 	SECAMScan	RateHorizontal: 	15	kHz	to	100	kHz	(RGB: 	24	kHz	or	over)Vertical:	50	Hz	to	120	Hz	(HDMI: 	50	Hz	to	85	Hz)Sync	CompatibilitySeparate	SyncBuilt-in	Speaker20	W	(monaural)Power	Requirement100–240V	AC,	50/60HzInput	Current3.9-1.6A 3.3-1.4A3.9-1.6APower	Consump-
tion
(Typical	value)
ECO	MODE	OFF
354W	(100-130V)335W	(200-240V)300W	(100-130V)286W	(200-240V)354W	(100-130V)335W	(200-240V)
NORMAL292W	(100-130V)278W	(200-240V)233W	(100-130V)224W	(200-240V)292W	(100-130V)278W	(200-240V)ECO258W	(100-130V)246W	(200-240V)210W	(100-130V)202W	(200-240V)258W	(100-130V)246W	(200-240V)STANDBY	(NETWORK	STANDBY)
2.5	W(100-130V)2.9	W	(200-240V)
STANDBY	(NORMAL)0.2W	(100-130V)0.38W	(200-130V)
Mechanical
Model	NumberNP-M352WS NP-M302WS NP-M332XS
Installation
OrientationDesktop/Front,	Desktop/Rear,	Ceiling/Front,	Ceiling/Rear
Dimensions14.5"	(W)	×	5.3"	(H)	×	11.5"	(D)	/368	mm	(W)	×	134	mm	(H)	×	291	mm	(D)14.5"	(W)	×	3.9"	(H)	×	11.3"	(D)	/368	mm	(W)	×	98	mm	(H)	×	286	mm	(D)	(not	including	protrusions)WeightM352W/M332XS: 	8.2	lbs/3.7	kgM302WS:	8.0	lbs/3.6	kgEnvironmental	ConsiderationsOperational	 Temperatures	: 	41°	to	104°F	(5°	to	40°C),	(ECO	mode	selected	automatically	at	95°F	to	104°F/35°C	to	40°C)	20%	to	80%	humidity	(non-condensing)	Storage	Temperatures	: 	14°	to	122°F	(-10°	to	50°C),	20%	to	80%	humidity	(non-condensing)Operating	altitude: 	0	to	2400m/8000	feet	(Set	[FAN	MODE]	to	[HIGH	ALUTITUDE]	when	using	the	pro-jector	at	altitudes	approximately	1700	meters	/5500	feet)RegulationsUL/C-UL	Approved	(UL	60950-1,	CSA	60950-1)Meets	DOC	Canada	Class	B	requirementsMeets	FCC	Class	B	requirementsMeets	AS/NZS	CISPR.22	Class	BMeets	EMC	Directive	(EN55022,	EN55024,	EN61000-3-2,	EN61000-3-3)Meets	Low	Voltage	Directive	(EN60950-1,	 TÜV	GS	Approved)
For	additional	information	visit:
US	:	http://www.necdisplay.com/
Europe	: 	http://www.nec-display-solutions.com/
Global	:	http://www.nec-display.com/global/index.html
For	information	on	our	optional	accessories,	visit	our	website	or	see	our	brochure.
The	specifications	are	subject	to	change	without	notice. 
						

							136
8. Appendix
368 (14.5)
286(11.3)
134 (5.3)
130 (5.2) 150 (5.9)
200 (7.9)
175 (6.9)
98 (3.9)
80 (3.2)
108 (4.3)
291 (11.5)
❸ Cabinet Dimensions
[M352WS/M302WS/M332XS]
Lens center
Lens center
Holes for ceiling mount
Unit:	mm	(inch) 
						

							137
8. Appendix
Attaching the Optional Cable Cover (NP05CV)
An	optional	cable	cover	(NP05CV)	is	available	for	hiding	cables.
 CAUTION:
•	 Be	sure	to	tighten	 the	screws	 after	attaching	 the	cable	 cover.	Failure	 to	do	 so	may	 cause	 the	cable	 cover	 to	come	
off	and	fall,	resulting	in	injury	or	damage	to	the	cable	cover.
•	 Do	not	put	bundled	cables	in	the	cable	cover. 	Failure	to	do	so	may	damage	the	power	cord,	resulting	a	fire.
•	 Do	not	force	 excessive	 pressure	to	the	 cable	 cover.	Doing	 so	may	 cause	 damage	 to	the	 cable	 cover,	 resulting	
in	injury.
Attaching	the	cable	cover
Attach	the	cable	cover	after	installing	the	projector	on	the	ceiling	and	connecting	cables.
Tool	needed	for	attaching:
•	 Phillips	screwdriver	(plus-head)
1.	 Align	two	tabs	on	the	outside	of	the	cable	cover	with	grooves	of	the	projector	and	push	the	top	end.
•	 At	the	same	 time	two	tabs	 on	the	 inside	 of	the	 cable	 cover	 will	be	engaged	 in	the	 responding	 grooves	of	the	
projector.
NOTE:
•	 Be	careful	not	to	get	cables	caught	in	between	the	cable	cover	and	the	 projector.
2.	 Tighten	the	cable	cover	screws.
•	 Be	sure	to	tighten	the	screws.
1
12
2
Removing	the	cable	cover
1.	 Loosen	the	cable	cover	screws	until	the	Phillips	screwdriver	goes	into	a	freewheeling	condition
 
1
1
2. Remove the cable cover.
  Push up the cable cover slightly and rotate it to release. 
						

							138
8. Appendix
❹ Pin Assignments of D-Sub COMPUTER Input Connector
Mini D-Sub 15 Pin Connector
Signal	Level
Video	signal	:	0.7Vp-p	(Analog)
Sync	signal	:	TTL	level
5
14 23 10
11 12 13 14 15
69 78
Pin No. RGB	Signal	(Analog)YCbCr	Signal1 Red Cr
2Green	or	Sync	on	GreenY
3 Blue Cb
4 Ground
5 Ground
6
Red	GroundCr	Ground7Green	GroundY	Ground8Blue	GroundCb	Ground9Hot	plug10Sync	Signal	Ground11No	Connection12Bi-directional	DATA	(SDA)13Horizontal	Sync	or	Composite	
Sync
14Vertical	Sync15Data	Clock
COMPUTER IN
NOTE:	Pin	Nos.	12	and	15	are	required	for	DDC/CI. 	 
						

							139
8. Appendix
❺ Compatible Input Signal List
Analog RGB
SignalResolution(	dots	)Aspect	RatioRefresh	Rate(	Hz	)VGA
640×480 4:360/72/75/85
SVGA 800×600 4:356/60/72/75/85
XGA 1024×768 *
14:3 60/70/75/85
WXGA 1280×768 *215:9 60
1280 ×800 *216:10 60
1360 ×768 *316:9 60
1366 ×768 *316:9 60
Quad-VGA 1280×960 4:3 60/75
SXGA 1280×1024 5:4 60/75
SXGA+ 1400×1050 4:3 60
WXGA+ 1440×900 16:10 60
WXGA++ 1600×900 *
316:9 60
UXGA 1600×1200 *44:3 60
WSXGA+ 1680×1050 16:10 60
HD 1280×720 16:9 60
Full	HD1920×1080 16:9 60
WUXGA 1920×1200 *516:10 60MAC	13"640×480 4:3 67MAC	16"832×624 4:3 75MAC	19"1024×768 4:3 75MAC	21"1152×870 4:3 75MAC	23"1280×1024 5:4 65
Component
Signal FormatAspect	RatioRefresh	Rate(	Hz	)HDTV	(1080p)1920×1080 16:9 50/60HDTV	(1080i)1920×1080 16:9 50/60HDTV	(720p)1280×720 16:9 50/60SDTV	(480p)720×480 4:3/16:9 60SDTV	(576p)720×576 4:3/16:9 50SDTV	(480i)720×480 4:3/16:9 60SDTV	(576i)720×576 4:3/16:9 50
Composite	Video
SignalAspect	RatioRefresh	Rate(	Hz	)NTSC 4:360
PAL 4:350
PAL60 4:360
SECAM 4:350
NOTE:
•	 An	image	 with	higher	 or	lower	 resolution	 than	the	projector’s	 native	resolution	 (M332XS:	 1024	×	768	 /	M352WS/M302WS:	 1280	
×	800)	will	be	displayed	with	Advanced	AccuBlend.
•	 Sync	on	Green	and	Composite	sync	signals	are	not	supported.
•	 Signals	other	than	those	 specified	 in	the	 table	 above	 may	not	be	displayed	 correctly.	If	this	 should	 happen,	 change	the	refresh	
rate	or	resolution	on	your	PC.	Refer	to	Display	Properties	help	section	of	your	PC	for	procedures.
HDMI
Signal Resolution(	dots	)Aspect	RatioRefresh	Rate(	Hz	)VGA
640×480 4:3 60
SVGA 800×600 4:3 60
XGA 1024×768 *
14:3 60
WXGA 1280×768 *215:9 60
1280 ×800 *216:10 60
1366 ×768 16:9 60
Quad-VGA 1280×960 4:3 60
SXGA 1280×1024 5:4 60
SXGA+ 1400×1050 4:3 60
WXGA+ 1440×900 16:10 60
WXGA++ 1600×900 16:9 60
WSXGA+ 1680×1050 16:10 60
HDTV	(1080p)1920×1080 16:9 50/60HDTV	(1080i)1920×1080 16:9 50/60HDTV	(720p)1280×720 16:9 50/60SDTV	(480p)720×480 4:3/16:9 60SDTV	(576p)720×576 4:3/16:9 50SDTV	(480i)720	(1440)×
480 4:3/16:9 60SDTV	(576i)720	(1440)×
576 4:3/16:9 50
3D
SignalResolution(	dots	)Aspect	RatioRefresh	Rate(	Hz	)For	PC	SignalXGA
1024×768 4:3 60/120
HD 1280×720 16:9 60/120
WXGA 1280×800 16:10 60/120
HDTV	(1080p)1920×1080 16:9 60For	Video	SignalSDTV	(480i)720 ×480 4:3/16:9 60
HDMI 3D
SignalResolution(	dots	)Aspect	RatioRefresh	Rate(	Hz	)Structure:
	Frame	Packing1080p 1920×1080 16:9 23.98/24
720p 1280×720 16:9 50/59.94/60
Structure:	Side	by	Side	(Half)1080i 1920×1080 16:950/59.94/60Structure:	Top	and	Bottom1080p 1920×1080 16:9 23.98/24
720p 1280×720 16:9 50/59.94/60
*1	Native	resolution	on	XGA	model	(M332XS)	*2	Native	resolution	on	 WXGA	model	(M352WS/M302WS)*3	The	projector	may	fail	to	display	these	signals	correctly	when	[AUTO]	is	selected	for	[ASPECT	RATIO]	in	the	on-screen	menu.	 The	factory	default	is	[AUTO]	for	[ASPECT	RATIO]. 	To	display	these	signals,	select	[16:9]	for	[ASPECT	RATIO].*4	WXGA	MODE: 	OFF*5	WXGA	MODE:	ON