NEC M332xs Projector Users Manual

110
5. Using On-Screen Menu
[SOURCE(1)]
[RESOLUTION]	[HORIZONTAL	FREQUENCY]
[VERTICAL	FREQUENCY]	[SYNC	TYPE]
[SYNC	POLARITY]	 [SCAN	TYPE]
[SOURCE(2)]
[SIGNAL	 TYPE]	 [VIDEO	TYPE]
[BIT	DEPTH]	 [VIDEO	LEVEL]
[3D	SIGNAL]
[WIRED LAN]
[IP	ADDRESS]	[SUBNET	MASK]
[GATEWAY]	[MAC	ADDRESS] 

111
5. Using On-Screen Menu
[WIRELESS LAN]
[IP	ADDRESS]	[SUBNET	MASK]
[GATEWAY]	[MAC	ADDRESS]
[SSID]	[NETWORK	TYPE]
[WEP/WPA]	 [CHANNEL]
[SIGNAL	LEVEL]
[VERSION(1)]
[FIRMWARE]	Version
[DATA]	Version
[VERSION(2)]
[FIRMWARE2]	 Version 

112
5. Using On-Screen Menu
[OTHERS]
[PROJECTOR	NAME]
[MODEL	NO.]
[SERIAL	NUMBER]
[LAN	UNIT	TYPE]
[CONTROL	ID]	(when	[CONTROL	ID]	is	set) 

113
5. Using On-Screen Menu
❽ Menu Descriptions & Functions [RESET]
Returning to Factory Default [RESET]
The	RESET	 feature	allows	you	to	change	 adjustments	 and	settings	 to	the	 factory	 preset	for	a	(all)	 source	 (s)	except	
the	following:
[CURRENT	SIGNAL]
Resets	the	adjustments	for	the	current	signal	to	the	factory	preset	levels. 	
The	items	 that	can	be	reset	 are:	[PRESET],	 [CONTRAST],	 [BRIGHTNESS],	 [COLOR],	[HUE],	[SHARPNESS],	
[ASPECT	 RATIO],	[HORIZONTAL],	 [VERTICAL],	[CLOCK],	[PHASE],...

114
6. Installation and Connections
32
1
This	section	describes	how	to	set	up	your	projector	and	how	to	connect	video	and	audio	sources.
Your	projector	is	simple	to	set	up	and	use.	But	before	you	get	started,	you	must	first:
①	 Set	up	a	screen	and	the	projector.
②	 Connect	your	computer	 or	video	 equip-
ment	to	the	projector.
	(→	page	117 , 119 , 120 , 121 , 122 , 
123)
③
	 Connect	 the	supplied	 power	cord. 
(→
	page	16)
NOTE:	 Ensure	 that	the	power	 cord	and	any	other	
cables	 are	disconnected...

115
6. Installation and Connections
[M352WS/M302WS]
The	further	 your	projector	 is	from	 the	screen	 or	wall,	 the	larger	 the	image. 	The	 minimum	 size	the	image	 can	be	is	ap-
proximately	 60"	(1.52	 m)	measured	 diagonally	 when	the	projector	 is	roughly	 22	inches	 (0.6	m)	from	 the	wall	 or	screen. 	
The	largest	the	image	can	be	is	150"	(3.8	m)	when	the	projector	is	about	58	inches	(1.5	m)	from	the	wall	or	screen.
150
120
Distance 
(Unit: m/inch)
Lens center Screen Size...

116
6. Installation and Connections
B
D
Cα
Throw Distance and Screen Size
The	
following	 shows	the	proper	 relative	 positions	 of	the	 projector	 and	screen. 	Refer	 to	the	 table	 to	determine	 the	
position	of	installation.
Distance Chart
B	=	 Vertical 	distance 	between 	lens 	center 	and	
screen center
C	=	 Throw	distance
D	=	 Vertical 	distance 	between 	lens 	center 	and	
screen	 bottom	 (top	of	screen	 for	ceiling	 ap-
plication)
α
	=	 Throw	angle
NOTE:	 The	values	 in	the	 tables	 are	design...

117
6. Installation and Connections
HDMI 2 IN
HDMI 1 IN
COMPUTER IN
USB-B
AUDIO IN
Computer cable (VGA) (supplied)To mini D-Sub 15-pin connector on	the	projector. 	It	is	recommend-
ed that you use a commercially 
available distribution amplifier if 
connecting a signal cable longer 
than the cable supplied.
NOTE: 	For 	Mac, 	use 	a 	commercially	
available	 pin	adapter	 (not	sup-
plied) 	to 	connect 	to 	your 	Mac’s	
video	port.
A commercially available USB cable 
(compatible with USB 2.0...

118
6. Installation and Connections
•	 Select	the	source	name	for	its	appropriate	input	connector	after	turning	on	the	projector.
Input	connectorSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTER(COMP1)
HDMI	1	IN	HDMI1HDMI1
HDMI	2	IN	HDMI2HDMI2
USB-B
	USB-B(USB-B)
NOTE:	The	projector	is	not	compatible	with	video	decoded	outputs	of	the	NEC	ISS-6020	switcher.
NOTE:	An	image	may	not	be	displayed	correctly	when	a	Video	source	is	played	back	via	a	commercially	available...

119
6. Installation and Connections
Connecting an External Monitor
You	can	connect	 a	separate,	 external	monitor	to	your	 projector	 to	simultaneously	 view	on	a	monitor	 the	computer	
analog	image	you’re	projecting.
NOTE:
•	 Daisy	chain	connection	is	not	possible.
•	 When	audio	equipment	is	connected,	the	projector	speaker	is	disabled.
Monitor	out	and	sleep	mode:
•	 The	MONITOR	OUT	(COMP.)	connector	will	not	work	when	[NORMAL]	is	selected	for	[STANDBY	MODE].
	 The	MONITOR	OUT	(COMP.)	connector	will...