NEC M322x Projector Users Manual

100
5. Using On-Screen Menu
Selecting Communication Speed [COMMUNICATION SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	38400	 bps.	The	
default	 is	38400	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	 equip-
ment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE:	Your	selected	communication	speed	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Setting...

101
5. Using On-Screen Menu
Using Test Pattern [TEST PATTERN]
Displays	the	test	 pattern	 to	check	 for	image	 distortion	 at	the	 time	 of	the	 projector	 setup.	Press	 the	ENTER	 button	to	
display	 the	test	 pattern; 	press	 the	EXIT	 button	 to	close	 the	test	 pattern	 and	return	 to	the	 menu. 	Menu	 operation	 and	
keystone	correction	are	not	possible	when	the	test	pattern	is	displayed.
Selecting	Microphone	 Type	[MIC	SELECT]
This	feature	allows	you	to	select	dynamic	or	condenser	type	for	your...

102
5. Using On-Screen Menu
Selecting Signal Format [COLOR SYSTEM]
This	feature	allows	you	to	select	video	standards	manually.
Normally	select	[AUTO].	Select	the	video	standard	from	the	pulldown	menu. 	
Enabling	or	Disabling	WXGA	Mode	[WXGA	MODE]
Selecting	[ON]	will	give	 priority	 to	WXGA	 (1280	×	768)/WUXGA	 (1920	×	1080)	 signals	 in	recognizing	 an	input	 sig-
nal.
When	 [WXGA	 MODE]	is	set	 to	[ON],	 XGA	(1024	 ×	768)/UXGA	 (1600	×	1200)	 signals	 may	not	be	recognized	 on...

103
5. Using On-Screen Menu
[OPTIONS(2)]
Selecting	Standby	condition	in	[STANDBY	MODE]
The	projector	has	two	standby	modes:	[NORMAL]	and	[NETWORK	STANDBY].
The	[NORMAL]	 mode	is	the	 mode	 that	allows	 you	to	put	 the	projector	 in	the	 power-saving	 condition	which	consumes	
less	power	than	the	[NETWORK	STANDBY]	mode. 	The	projector	is	preset	for	the	[NORMAL]	mode	at	the	factory.
NORMAL �����������������������������POWER indicator: Red light/STATUS indicator: Off
When [NORMAL] is selected, only the...

104
5. Using On-Screen Menu
Turning	On	the	Projector	By	Applying	Computer	Signal	[AUTO	POWER	ON(COMP.)]
When	the	projector	 is	in	 Standby	 mode,	applying	 a	computer	 signal	from	a	computer	 connected	 to	the	 COMPUTER	
IN	input	will	power	on	the	projector	and	simultaneously	project	the	computer’s	image.
This	 functionality	 eliminates	the	need	 to	always	 use	the	POWER	 button	on	the	 remote	 control	or	the	 projector	 cabinet	
to	power	on	the	projector.
To	use	this	function,	first	connect	a	computer...

105
5. Using On-Screen Menu
Setting	carbon	footprint	factor	[CARBON	CONVERT]
Adjusts	the	carbon	 footprint	 factor	in	the	 carbon	 saving	calculation. 	The	 initial	 setting	 is	0.505[kg-CO2/kWh]	 based	on	
the	CO2	Emissions	from	Fuel	Combustion	(2008	Edition)	published	by	OECD.
Selecting	your	currency	[CURRENCY]
Displays	electricity	pricing	(available	in	4	currency	units).
$ ����������������������������US Dollar
€
  ���������������������������EU Euro
JP¥
  ������������������������Japanese Yen
RMB¥...

106
5. Using On-Screen Menu
[3D]
Selecting	input	connected	to	a	source	of	3D	images	[COMPUTER/HDMI1/HDMI2/VIDEO]
[3D]
This	function	switches	the	3D	mode	between	ON	and	OFF	for	each	input.
ON �������������������������Turns on the 3D mode for the selected input�
NOTE:
To	confirm	that	the	supported	3D	signal	is	accepted,	use	either	way	of	the	following:
•	 Make	sure	that	[3D]	is	displayed	in	the	top	right	of	the	screen	after	the 	source	is	selected.
•	 Display	[INFO.]	→	[SOURCE]	→	[3D	SIGNAL]	and	make	sure...

107
5. Using On-Screen Menu
[L/R	INVERT]
Change	the	setting	if	you	have	difficulty	seeing	3D	images.
NON-INVERT ���������Normal setting�
INVERT ������������������Changes the order of displaying the images for left eye and right eye�
NOTE:
This	option	is	available	only	when	[DLP®	Link]	is	selected	for	[GLASSES]. 

108
5. Using On-Screen Menu
Setting up the Projector for a Wired LAN Connection [WIRED LAN]
Important
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wired	 LAN	connection,	 connect	a	LAN	 cable	 (Ethernet	 cable)	to	the	 LAN	 port	(RJ-45)	 of	the	 projec-
tor.	(→	page	127)
TIP:	The	network	settings	you	make	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
[WIRED	LAN][DISABLE]Wired	LAN	connection	will	be	turned	off.
[ENABLE]Wired	LAN	connection	will	be	turned...

109
5. Using On-Screen Menu
Setting up the Projector for a Wireless LAN Connection (with the optional USB Wireless 
LAN Unit equipped) [WIRLESS LAN]
Important
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wireless	LAN	connection,	attach	the	optional	USB	Wireless	LAN	to	the	projector.	(→	page	128)
[PROFILE][DISABLE]Wireless	LAN	connection	will	be	turned	off
[EASY	CONNECTION]Select	[EASY	 CONNECTION]	 to	execute	 a	wireless	 LAN	
easily	using	Image	 Express	 Utility	Lite...