NEC M311x Portbale Projector Users Manual
Have a look at the manual NEC M311x Portbale Projector Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 37
27
3. Convenient Features
Changing Eco Mode/Checking Energy-Saving Effect
Using Eco Mode [ECO MODE]
The ECO MODE (NORMAL and ECO) increases lamp life, while lowering power consumption and cutting down on
CO2 emissions.
Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL] and [ECO] modes.
[ECO MODE] DescriptionStatus of LAMP indicator
[OFF]The lamp brightness is 100%.Off
[AUTO ECO]Lamp power consumption will be changed between
[OFF] and [NORMAL]...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-36.png "Page 37
27
3. Convenient Features
Changing Eco Mode/Checking Energy-Saving Effect
Using Eco Mode [ECO MODE]
The ECO MODE (NORMAL and ECO) increases lamp life, while lowering power consumption and cutting down on
CO2 emissions.
Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL] and [ECO] modes.
[ECO MODE] DescriptionStatus of LAMP indicator
[OFF]The lamp brightness is 100%.Off
[AUTO ECO]Lamp power consumption will be changed between
[OFF] and [NORMAL]...")
![Page 38
28
3. Convenient Features
NOTE:
• The [ECO MODE] can be changed by using the menu.
Select [SETUP] → [GENERAL] → [ECO MODE].
• The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] →[USAGE TIME].
• The projector is always in [NORMAL] for 90 seconds after the lamp is turned on and while the POWER indicator is blinking green.
The lamp condition will not be affected even when [ECO MODE] is changed.
• After a lapse of 1 minute from when the projector...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-37.png "Page 38
28
3. Convenient Features
NOTE:
• The [ECO MODE] can be changed by using the menu.
Select [SETUP] → [GENERAL] → [ECO MODE].
• The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] →[USAGE TIME].
• The projector is always in [NORMAL] for 90 seconds after the lamp is turned on and while the POWER indicator is blinking green.
The lamp condition will not be affected even when [ECO MODE] is changed.
• After a lapse of 1 minute from when the projector...")
![Page 39
29
3. Convenient Features
Preventing the Unauthorized Use of the Projector [SECURITY]
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro-
jector cannot project an image.
• The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu.
To enable the Security function:
1. Press the MENU...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-38.png "Page 39
29
3. Convenient Features
Preventing the Unauthorized Use of the Projector [SECURITY]
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro-
jector cannot project an image.
• The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu.
To enable the Security function:
1. Press the MENU...")
![Page 40
30
3. Convenient Features
7. Type in the same combination of buttons and press the ENTER button.
The confirmation screen will be displayed.
8. Select [YES] and press the ENTER button.
The SECURITY function has been enabled.
To turn on the projector when [SECURITY] is enabled:
1. Press the POWER button.
The projector will be turned on and display a message to the effect that the projector is locked.
2. Press the MENU button.
3. Type in the correct keyword and press the ENTER button. The...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-39.png "Page 40
30
3. Convenient Features
7. Type in the same combination of buttons and press the ENTER button.
The confirmation screen will be displayed.
8. Select [YES] and press the ENTER button.
The SECURITY function has been enabled.
To turn on the projector when [SECURITY] is enabled:
1. Press the POWER button.
The projector will be turned on and display a message to the effect that the projector is locked.
2. Press the MENU button.
3. Type in the correct keyword and press the ENTER button. The...")
![Page 41
31
3. Convenient Features
To disable the SECURITY function:
1. Press the MENU button.
The menu will be displayed.
2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button.
The OFF/ON menu will be displayed.
3. Select [OFF] and press the ENTER button.
The SECURITY KEYWORD screen will be displayed.
4. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the SECURITY function will be disabled.
NOTE: If you forget your keyword, contact your...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-40.png "Page 41
31
3. Convenient Features
To disable the SECURITY function:
1. Press the MENU button.
The menu will be displayed.
2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button.
The OFF/ON menu will be displayed.
3. Select [OFF] and press the ENTER button.
The SECURITY KEYWORD screen will be displayed.
4. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the SECURITY function will be disabled.
NOTE: If you forget your keyword, contact your...")
![Page 43
33
3. Convenient Features
NOTE:
• When [COMPUTER 1] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well
as your computer screen.
• Use the supplied computer cable (VGA) to connect the COMPUTER 1 IN connector directly with the monitor output connector of
the computer to use Virtual Remote Tool.
Using a switcher or other cables than the supplied computer cable (VGA) may cause failure in signal communication.
VGA cable...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-42.png "Page 43
33
3. Convenient Features
NOTE:
• When [COMPUTER 1] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well
as your computer screen.
• Use the supplied computer cable (VGA) to connect the COMPUTER 1 IN connector directly with the monitor output connector of
the computer to use Virtual Remote Tool.
Using a switcher or other cables than the supplied computer cable (VGA) may cause failure in signal communication.
VGA cable...")
![Page 44
34
3. Convenient Features
TIP:
If the menu window will not be displayed, try the following procedure.
For Windows 7
1. Click “start” on Windows.
2. Click “All Programs” → “Accessories” → “Run”.
3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\
LAUNCHER.EXE)
4. Click “OK”.
The menu window will be displayed.
2 Click “Install Virtual Remote Tool” on the menu window.
The installation will start.
When the installation is complete, the Welcome...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-43.png "Page 44
34
3. Convenient Features
TIP:
If the menu window will not be displayed, try the following procedure.
For Windows 7
1. Click “start” on Windows.
2. Click “All Programs” → “Accessories” → “Run”.
3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\
LAUNCHER.EXE)
4. Click “OK”.
The menu window will be displayed.
2 Click “Install Virtual Remote Tool” on the menu window.
The installation will start.
When the installation is complete, the Welcome...")
![Page 46
36
3. Convenient Features
Step 3: Start Virtual Remote Tool
Start using the shortcut icon
• Double-click the shortcut icon on the Windows Desktop.
Start from the Start menu
• Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool]
→ [Virtual Remote Tool].
When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
Follow the instructions on the screens
When “Easy Setup” is completed, the Virtual Remote...](http://img.usermanuals.tech/thumb/54/91902/w64_nec-m311x-manual_d-45.png "Page 46
36
3. Convenient Features
Step 3: Start Virtual Remote Tool
Start using the shortcut icon
• Double-click the shortcut icon on the Windows Desktop.
Start from the Start menu
• Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool]
→ [Virtual Remote Tool].
When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
Follow the instructions on the screens
When “Easy Setup” is completed, the Virtual Remote...")
31 3. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen will be displayed. 4. Type in your keyword and press the ENTER button. When the correct keyword is entered, the SECURITY function will be disabled. NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request code. Your request code is displayed in the Keyword Confirmation screen. In this example [NB52-YGK8-2VD6-K585-JNE6-EYA8] is a request code.
32 3. Convenient Features Using the Computer Cable (VGA) to Operate the Projector (Virtual Remote Tool) Using the utility software “Virtual Remote Tool” included on the companion NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed on your computer screen. This will help you perform operations such as projector’s power on or off and signal selection via the computer cable (VGA), serial cable, or LAN connection. Only via serial or LAN connection it is also used to send an image to the projector and register it as the logo data of the projector. After registering it, you can lock the logo to prevent it from changing. Control Functions Power On/Off, signal selection, picture freeze, picture mute, audio mute*, Logo transfer to the projector, and remote control operation on your PC. Virtual Remote screenToolbar This section provides an outline of preparation for use of Virtual Remote Tool. For information on how to use Virtual Remote Tool, see Help of Virtual Remote Tool. (→ page 37) Step 1: Install Virtual Remote Tool on the computer. (→ page 33) Step 2: Connect the projector to the computer. (→ page 35) Step 3: Start Virtual Remote Tool. (→ page 36) TIP: • Virtual Remote Tool can be used with a LAN and a serial connection. USB connection is not supported by Virtual Remote Tool. • For update information on Virtual Remote Tool, visit our website: http://www.nec-display.com/dl/en/index.html
33 3. Convenient Features NOTE: • When [COMPUTER 1] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well as your computer screen. • Use the supplied computer cable (VGA) to connect the COMPUTER 1 IN connector directly with the monitor output connector of the computer to use Virtual Remote Tool. Using a switcher or other cables than the supplied computer cable (VGA) may cause failure in signal communication. VGA cable connector: Pin Nos. 12 and 15 are required for DDC/CI. • Virtual Remote Tool may not work depending on your computer’s specifications and version of graphic adapters or drivers. • To run Virtual Remote Tool on Windows XP Home Edition and Windows XP Professional, “Microsoft .NET Framework Version 2.0 or later” is required. The Microsoft .NET Framework Version 2.0 or later is available from Microsoft’s web page. Download and install the it on your computer. • Logo data (graphics) that can be sent to the projector with Virtual Remote Tool has the following restrictions: (Only via serial or LAN connection) - File size: Less than 1 MB - Image size (resolution): M361X/M311X/M271X: Horizontal 1024 × vertical 768 dots or less M311W/M271W: Horizontal 1280 × vertical 800 dots or less - Number of colors: 256 colors or less TIP: • The projector’s COMPUTER 1 IN connector supports DDC/CI (Display Data Channel Command Interface). DDC/CI is a standard interface for bidirectional communication between display/projector and computer. Step 1: Install Virtual Remote Tool on the computer NOTE: • To install Virtual Remote Tool, the Windows user account must have “Administrator” privilege (Windows 7, Windows Vista and Windows XP). • Exit all running programs before installing Virtual Remote Tool. If another program is running, the installation may not be com- pleted. 1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed.
34 3. Convenient Features TIP: If the menu window will not be displayed, try the following procedure. For Windows 7 1. Click “start” on Windows. 2. Click “All Programs” → “Accessories” → “Run”. 3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\ LAUNCHER.EXE) 4. Click “OK”. The menu window will be displayed. 2 Click “Install Virtual Remote Tool” on the menu window. The installation will start. When the installation is complete, the Welcome window will be displayed. 3 Click “Next”. “END USER LICENSE AGREEMENT” screen will be displayed. Read “END USER LICENSE AGREEMENT” carefully. 4 If you agree, click “I accept the terms in the license agreement” and then click “Next”. • Follow the instructions on the installer screens to complete the installation. • When the installation is complete, you will return to the menu window.
35 3. Convenient Features TIP: Uninstalling Virtual Remote Tool Preparation: Exit Virtual Remote Tool before uninstalling. To uninstall Virtual Remote Tool, the Windows user account must have “Administrator” privilege (Windows 7 and Windows Vista) or “Computer Administrator” privilege (Windows XP). • For Windows 7/Windows Vista 1 Click “Start” and then “Control Panel”. The Control Panel window will be displayed. 2 Click “Uninstall a program” under “Programs” The “Programs and Features” window will be displayed. 3 Select Virtual Remote Tool and click it. 4 Click “Uninstall/Change” or “Uninstall”. • When the “User Account Control” windows is displayed, click “Continue”. Follow the instructions on the screens to complete the uninstallation. • For Windows XP 1 Click “Start” and then “Control Panel”. The Control Panel window will be displayed. 2 Double-click “Add / Remove Programs”. The Add / Remove Programs window will be displayed. 3 Click Virtual Remote Tool from the list and then click “Remove”. Follow the instructions on the screens to complete the uninstallation. Step 2: Connect the projector to the computer 1 Use the supplied computer cable (VGA) to connect the COMPUTER 1 IN connector of the projector directly with the monitor output connector of the computer. 2 Connect the supplied power cord to the AC IN of the projector and the wall outlet. The projector is in the standby condition. COMPUTER 1 IN TIP: • When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed to navigate your connections. AC Input Supplied computer cable (VGA) → To wall outlet Power cord (supplied)
36 3. Convenient Features Step 3: Start Virtual Remote Tool Start using the shortcut icon • Double-click the shortcut icon on the Windows Desktop. Start from the Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed. Follow the instructions on the screens When “Easy Setup” is completed, the Virtual Remote Tool screen will be displayed. NOTE: • When [POWER-SAVING] is selected for [STANDBY MODE] from the menu, the projector cannot be turned on via the computer cable (VGA) or network (wired LAN/wireless LAN) connection. TIP: • The Virtual Remote Tool screen (or Toolbar) can be displayed without displaying “Easy Setup” window. To do so, click to place a check mark for “ Do not use Easy Setup next time” on the screen at Step 6 in “Easy Setup”.
37 3. Convenient Features Exiting Virtual Remote Tool 1 Click the Virtual Remote Tool icon on the Taskbar. The pop-up menu will be displayed. 2 Click “Exit”. The Virtual Remote Tool will be closed. Viewing the help file of Virtual Remote Tool • Displaying the help file using the taskbar 1 Click the Virtual Remote Tool icon on the taskbar when Virtual Remote Tool is running. The pop-up menu will be displayed. 2. Click “Help”. The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “Virtual Remote Tool” → and then “Virtual Remote Tool Help” in this order. The Help screen will be displayed.
38 3. Convenient Features Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function) The built-in remote mouse function enables you to operate your computer’s mouse functions from the supplied remote control when the projector is connected to a computer via a commercially available USB cable (compatible with USB 2.0 specifications). The Remote Mouse function works for the COMPUTER 1 or COMPUTER 2 input while the computer screen is dis- played. The Remote Mouse function will not work while you freeze or magnify an image. - Using the USB cable to connect the projector and the computer will also start USB Display function. USB (PC) NOTE: • A USB cable must support the USB 2.0 Specifications. • The mouse function can be used with the following operating systems: Windows 7, Windows XP, or Windows Vista • In SP2 or older version of Windows XP, if the mouse cursor will not move correctly, do the following: Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer Options tab]. • Wait at least 5 seconds after disconnecting the USB cable before reconnecting it and vice versa. The computer may not identify the USB cable if it is repeatedly connected and disconnected in rapid intervals. • Connect the projector to the computer with a USB cable after starting the computer. Failure to do so may fail to start the com- puter. Operating your computer’s mouse from the remote control You can operate your computer’s mouse from the remote control. PAGE / Button ���������������������������scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer � Buttons ������������������������������moves the mouse cursor on your computer � MOUSE L-CLICK/ENTER Button ������works as the mouse left button� MOUSE R-CLICK Button ������������������works as the mouse right button� NOTE: • When you operate the computer using the or button with the menu displayed, both the menu and the mouse pointer will be affected. Close the menu and perform the mouse operation. TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user documentation or online help supplied with your computer. USB cable (not supplied)
39 3. Convenient Features Projecting Your Computer’s Screen Image from the Projector via the USB Cable (USB Display) Using a commercially available USB cable (compatible with USB 2.0 specifications) to connect the computer with the projector allows you to send your computer screen image to the projector for displaying. Power On/Off and source selection of the projector can be done from your computer without connecting a computer cable (VGA). NOTE: • To make USB DISPLAY available on Windows XP, the Windows user account must have “Administrator” privilege. • USB Display uses functions of Image Express Utility Lite contained on NEC Projector CD-ROM (→ page 52). Starting USB Display, however, will not install Image Express Utility Lite on your computer. This is because USB Display executes the projector’s program only. • USB Display will not work in [POWER-SAVING] of [STANDBY MODE]. (→ page 91) • When USB Display is used, the sound is output from the COMPUTER 2 AUDIO IN Mini Jack (Stereo Mini). Image and sound may not be synchronized. 1. Start the computer. 2. Connect the projector’s power cord to the wall outlet and put the projector into standby condition. • Open the projector’s lens cover. 3. Use the USB cable to connect the computer with the projector. USB (PC) USB cable (not supplied) → To wall outlet Power cord (supplied) The message “The projector is in standby mode. Connect it?” will be displayed on the computer screen. • The control window of Image Express Utility Lite will be displayed on the top of the screen. NOTE: Depending on the computer setting, the “AutoPlay” window may be displayed when the computer detects the connection to the projector. If this happens, click the “Start USB Display” window. 4. Click “Yes”. The projector will turn on and the message “The projector is getting ready. Please wait.” will be displayed on the computer screen. This message will disappear in a few seconds.
40 3. Convenient Features 5. Operate the control window. (1) (Source) �����Selects an input source of the projector � (2) (Picture) ����Turns on or off AV-MUTE (Picture mute), and turns on or off FREEZE (Freeze a picture)� (3) (Sound) �����Turns on or off AV-MUTE (Sound mute), play the sound and turns up or down the volume� (4) (Others) �����Uses “Update”, “HTTP Server”*, “Settings” and “Information”� * The HTTP Server cannot be selected when a USB cable is connected� (5) (Exit) ����������Exit Image Express Utility Lite� You can also turn off the projector at the same time� (6) (Help) �����������Displays the help of Image Express Utility Lite� (1)(2) (3)(4)(5) (6)