NEC M271w Portable Projector Users Manual

81
5. Using On-Screen Menu
Selecting	Aspect	Ratio	[ASPECT	RATIO]
The	term	“aspect	ratio” 	refers	to	the	ratio	of	width	to	height	of	a	projected	image.
The	projector	automatically	determines	the	incoming	signal	and	displays	it	in	its	appropriate	aspect	ratio.
•	This	table	shows	typical	resolutions	and	aspect	ratios	that	most	computers	support.
ResolutionAspect	RatioVGA640	×	4804:3
SVGA800	×	6004:3
XGA1024	×	7684:3
WXGA1280	×	76815:9
WXGA1280	×	80016:10
WXGA+1440	×	90016:10
SXGA1280	×	10245:4
SXGA+1400	×...

82
5. Using On-Screen Menu
Sample	image	when	the	appropriate	aspect	ratio	is	automatically	determined
M361X/M311X/M271X
[Computer	signal]
Aspect	ratio	of	incoming	signal4:35:416:9 15:916:10
Sample	image	when	the	appro-priate	 aspect	 ratio	is	automati-cally	determined
[Video	signal]
Aspect	ratio	of	incoming	signal4:3 Letterbox Squeeze
Sample	image	when	the	as-pect	 ratio	 is	automatically	 de-
termined
NOTE:	 To	display	 a	squeezed	 signal	prop-erly,	select	[16:9]	or	[WIDE	ZOOM].
M311W/M271W
[Computer...

83
5. Using On-Screen Menu
 Menu Descriptions & Functions [SETUP]
[GENERAL]
Enabling	Auto	Keystone	[AUTO	KEYSTONE]
This	feature	allows	the	projector	to	detect	its	tilt	and	correct	vertical	distortion	automatically.
To	turn	on	the	AUTO	KEYSTONE	feature,	select	[ON].	To	adjust	the	KEYSTONE	feature	manually,	select	[OFF].
NOTE:	 The	[AUTO	 KEYSTONE]	 function	is	not	 available	 when	an	orientation	 type	such	 as	[CEILING	 REAR],	[DESKTOP	 REAR],	
[CEILING	FRONT]	other	than	[DESKTOP/FRONT]	is	selected	for...

84
5. Using On-Screen Menu
Using	the	Wall	Color	Correction	[WALL	COLOR]
 
This	function	allows	for	quick	adaptive	color	correction	in	applications	where	the	screen	material	is	not	white.
NOTE:	Selecting	[WHITEBOARD]	reduces	lamp	brightness.
Setting	Eco	Mode	[ECO	MODE]
The	ECO	MODE	increases	lamp	life,	while	lowering	power	consumption	and	cutting	down	on	CO2 emissions. 
Four	brightness	modes	of	the	lamp	can	be	selected: 	[OFF],	[AUTO	ECO],	[NORMAL]	and	[ECO]	modes.	
(→	page	27) 

85
5. Using On-Screen Menu
Setting	Closed	Caption	[CLOSED	CAPTION]
This	option	 sets	several	 closed	caption	 modes	that	allow	 text	to	be	 superimposed	 on	the	 projected	 image	of	Video	
or	S-Video.
OFF ������������������������This exits the closed caption mode�
CAPTION 1-4 ���������Text is superimposed�
TEXT 1-4 ����������������Text is displayed�
NOTE:
•	 The	closed	caption	is	not	available	under	the	following	conditions:
-	 when	messages	or	menus	are	displayed.
-	 when	an	image	is	magnified,	frozen,...

86
5. Using On-Screen Menu
Turning	ON/OFF	Control	ID	[ID	DISPLAY]
ID DISPLAY �����������This option turns on or off the ID number which is displayed when the ID SET button on the remote control 
is pressed�
Turning	On	/	Off	Eco	Message	[ECO	MESSAGE]
This	option	turns	on	or	off	the	following	messages	when	the	projector	is	turned	on. 	
The	Eco	Message	 prompts	the	user	 to	save	 energy. 	When	 [OFF]	is	selected	 for	[ECO	 MODE],	 you	will	get	 a	message	
to	prompt	you	to	select	[AUTO	ECO],	[NORMAL],	or...

87
5. Using On-Screen Menu
[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	 your	image	 for	your	 type	of	projection. 	The	 options	 are:	desktop	 front	projection,	 ceiling	rear	projection,	
desktop	rear	projection,	and	ceiling	front	projection.
DESKTOP	FRONTCEILING	REAR
DESKTOP	REARCEILING	FRONT
Disabling	the	Cabinet	Buttons	[CONTROL	PANEL	LOCK]
This	option	turns	on	or	off	the	CONTROL	PANEL	LOCK	function.
NOTE:
•	 This	CONTROL	PANEL	LOCK	does	not	affect	the	remote	control...

88
5. Using On-Screen Menu
Selecting	Communication	Speed	[COMMUNICATION	SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	38400	 bps.	The	
default	 is	38400	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	 equip-
ment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE:	Your	selected	communication	speed	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Setting...

89
5. Using On-Screen Menu
Using	Test	Pattern	[TEST	PATTERN]
Displays	 the	test	 pattern	 to	check	 for	image	 distortion	 at	the	 time	 of	the	 projector	 setup.	Press	 the	ENTER	 button	to	
display	 the	test	 pattern; 	press	 the	EXIT	 button	 to	close	 the	test	 pattern	 and	return	 to	the	 menu. 	Menu	 operation	 and	
keystone	correction	are	not	possible	when	the	test	pattern	is	displayed.
[OPTIONS(1)]
Setting	Auto	Adjust	[AUTO	ADJUST]
This	feature	 sets	the	Auto	 Adjust	 mode	so	that	 the	computer...

90
5. Using On-Screen Menu
Selecting	Signal	Format	[SIGNAL	SELECT]
[COMPUTER1],	[COMPUTER2]
Allows	you	to	choose	 [COMPUTER1],	 or	[COMPUTER2]	 for	an	RGB	 source	 such	as	a	computer,	 or	[COMPONENT]	
for	 a	component	 video	source	 such	as	a	DVD	 player. 	Normally	 select	[RGB/COMPONENT]	 and	the	projector	 auto-
matically	detects	a	component	 signal.	However	 there	may	be	some	 component	 signals	that	the	projector	 is	unable	 to	
detect.	If	this	is	the	case,	select	[COMPONENT].
[VIDEO	&	S-VIDEO	System...