NEC Lt81 Projector Users Manual

39
INSTALLATION40
Transporting and storing the projector
[LT100]
MEMU
SELECT
ENTER
STATUS
POWER ON / OFFAC IN
2 1
Projector
Zipper
Note book PC
Other Accessories
2. Zip up the sides of the case.3. Hold the projector by itÕs handle and slide it into the large
compartment of the carrying case.
5. Unlatch the belt and then place your notebook computer into the
front pouch.
6. Latch the belt.7. Store the remote control and other accessories in the side
pouches on the carrying case.
2
1
When storing the...

     WARNING
¥Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.
¥ Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41ûF (5ûC) and 95ûF (35ûC).
¥ Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.
¥ Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the...

PC CONTROL
VIDEO INPUT
RGB INPUT OUTPUT
OUTPUT S-VIDEO VIDEO L(MONO)-R-AUDIOOUTPUTINPUT
RGB RGBAUDIO AUDIO
REMOTE
CONTROL
Document Camera
VCR, Laser Disk Player or DVD Player
Wiring Diagram
To video, S-video, and audio
inputs on the projector
43
IBM VGA or Compatibles Macintosh or Compatibles 
(Desk top type)
Remote Mouse
Receiver PS/2 mouse adapter
(supplied)
Mac ADB adapter
(supplied)
INSTALLATION44
Pin adapter for Macintosh
(supplied)
DVD Player with Y/Cb/Cr output
Signal cable (supplied)
To mini...

Connecting Your PC Or Macintosh Computer
Connecting your PC or Macintosh computer to your MultiSync LT81 (SVGA)/ LT100 (XGA) Projector will enable you to project your
computers screen image for an impressive presentation. All of these following display standards are supported:
* indicates that this resolution is supported by LT100 only.
To connect to a PC, Macintosh or computer equipped with an XGA/SVGA/VGA adapter or compatible graphics adapter, simply:
1. Turn off the power to your projector and...

Settings for Monitor Mode
Number of DIP switch
Monitor size
15Ó multi-scan mode /16ÓÐ13Ó
17Ó multi-scan mode /19ÓÐ13Ó
19Ó multi-scan mode /21ÓÐ13Ó
13Ó fixed mode /6402480
VGA/SVGA mode
16Ó fixed mode /8322624
19Ó fixed mode /10242768
47
INSTALLATION48
S1
ON
ON
ON
ONS2 S3 S4
ONS5
ON
ONS6
ONS7
ONS8
ON
NOTE: For setting other than display modes supported by your Macintosh and LT81/LT100, using of the
DIP switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the...

Changing Video Resolutions
Depending on your computers graphic capability, you may be able
to select one of several resolutions. Generally a computer- either a
PC or Macintosh- with 1 meg. of memory will run:
6402480 at 16.7 million colors (24 bit Truecolor)
8002600 at 65 thousand colors.
10242768 at 256 colors.
As the resolution increases,  the number of colors you can run de-
creases.  With 2 meg. of memory a computer will run:
6402480 at 16.7 million colors (24 bit Truecolor).
8002600 at 16.7 million...

Connecting Your DVD Player
You can connect your MultiSync LT81/LT100 Projector to a DVD player with the component outputs or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output use the optional 15-pin-to-RCA23 cable to connect your DVD player to the
RGB INPUT connector on the LT81/LT100.
For a DVD player without component video (Y,Cb,Cr) outputs, use common RCA cables (not provided) to connect a composite...

Connecting Your Remote Mouse Receiver
The remote mouse receiver enables you to operate your computers mouse functions from the NEC MultiSync LT81/
LT100 remote control. It is a great convenience for clicking through your computer-generated presentations.
To connect the remote mouse receiver:
1. Turn off your computer.
2. For PCs: Remove your current mouse and connect the serial cable from the remote mouse receiver to your PCs
mouse port. (Use the 6-pin adapter for connecting to a PS/2 computer.)
For...

mThe Remote Mouse Receiver as a mouse for your computer
INSTALLATION55
56
Serial cable (supplied)
Serial cable
(supplied) Remote cable
(supplied with LT100 only)Remote Control
Output
mThe Remote sensors on the projector cabinet work as the remote sensor
on the Remote Mouse Receiver (LT100 only)
mYou can daisy-chain as many as five projectors and operate them with the same remote control. (LT100 only)
To do so:
1. Turn off your computer.
2. Use the remote control cables supplied to connect the Remote...

This section describes how to select a computer or video source and how to adjust the
picture and sound.
General Controls Before you turn on your MultiSync LT81/LT100 Projector,  ensure
that the computer or video source is turned on and that your lens cap is removed.
1.Turn On The Projector The main power switch is on the back panel of the
MultiSync LT81/LT100 Projector. By turning this switch on, the projector will go
into its standby mode and the power light will glow amber. Only after you press the
On...