NEC Lt157 Lcd Projector Users Manual

E – 7
MENU
ENTERCANCELSELECT
POWERSTATUS ON
/STAND BY
SOURCE
AUTO 
ADJUST
PC  CARD 
ACCESS
Getting to Know Your LT158/LT157 Projector
Zoom leverRemote Sensor
Lens capAdjustable Tilt FootLens
Ventilation (inlet)
Air FilterControls
Front/Side Features
One-touch Tilt Button
Built-In Monaural Speaker (0.5W)
Focus ring
Attaching the lens cap to the bottom with the supplied string and rivet
1. Thread the string through the hole on the
lens cap and then tie a knot in the string.2. Use the rivet to attach the...

E – 8
MENU
ENTERCANCELS
E
L
E
C
T
P
O
W
E
R S
T
A
T
U
S O
N
/S
T
A
N
D
 B
Y
S
O
U
R
C
E
A
U
T
O 
A
D
J
U
S
T
P
C
  C
A
R
D
 
A
C
C
E
S
S
AC  IN
C CARD
PC CONTROLVIDEO
RGB
USBS-VIDEO
AUDIO
AC Input
Connect the supplied power cable’s three-
pin plug here.
Terminal Panel
Slot for Kensington Micro
saver Security System
Rear/Side Features
Rear FootRemote SensorVentilation (inlet)
Ventilation (outlet)
Bottom
Lamp cover
Lamp cover screwRear Foot
Rotate to fine-adjust horizontally
position
Spacer (black rubber)...

E – 9
1. Menu Button
Displays the menu.
2. Select 
 
  / Volume (+) (-) Buttons

: Use these buttons to select the menu of the item you wish to
adjust.
When no menus appear, these buttons work as a volume con-
trol.
 : Use these buttons to change the level of a selected menu item.
A press of the  button executes the selection.
When the menus or the Viewer tool bar is not displayed, these
buttons can be used to select a slide, or to move the cursor in
Folder List or Slide List.
When the pointer is...

E – 10
Terminal Panel Features
MENU
ENTER
CANCELSELECT
POWERSTATUS ON
/STAND BY
SOURCE
AUTO 
ADJUST
PC  CARD 
ACCESS
AC  IN
C CARD
PC CONTROLVIDEO
RGB
USBS-VIDEO
AUDIO
9
10 8
7
6
5
4
3
2
1
EO
DVI-DS-VIDEO
AUDIO
LT158
Slot for Kensington
MicroSaver Security System
1. Audio Input Mini Jack (3.5 mm ∅)
This is where you connect audio output from your computer, VCR,
DVD player or laser disc player.
A commercially available audio cable is required.
2. RGB Input/ Component Input Connector (Mini D-Sub 15 pin)...

E – 11
4. LED
Flashes when any button is pressed.
5. Power ON Button
If the main power is applied, you can use this button to turn your pro-
jector on.
P
JF
O
C
U
SZ
O
O
M
V
O
L
.S
H
IF
T
H
E
L
PPOINTERKEYSTONEMAGNIFY
FREEZE
PIC-MUTEPC CARDS
L
ID
EFOLDER
SLIDEL
IS
T
O
F
F
V
ID
E
O
A
U
T
O
 A
D
J
.S
-V
ID
E
OR
G
B
1R
G
B
2
L
A
S
E
R O
NP
O
W
E
R
SELECT
3
21
Remote Control Features
NOTE: If you are using a Macintosh computer, you can click either the right-click or left-click button to activate the mouse....

E – 12
PJ
FOCUS ZOOM
VOLUME
SHIFT
HELP
POINTER
KEYSTONEMAGNIFY
FREEZE
PIC-MUTEPC CARDSLIDE
FOLDER
SLIDE
LIST
17
19
20
28
29
30
31 22
18
21
23
24
25
26
27
17. PJ Button
Press this button to switch the Select, Cancel, and Enter buttons be-
tween the Projector mode (lit red) and the Computer mode. Press this
button or any one of the Power ON/OFF, Menu, Help, Pointer, Magnify,
PC Card, Folder List or Slide List buttons to switch to the Projector
mode and the PJ button lights red. To switch back to the...

E – 13
30˚7m
7m
30˚30˚
30˚
MENUENTERCANCELSELECT
POWERSTATUS ON/STAND BYSOURCE
AUTO  
ADJUST
PC  CARD 
ACCESS
Operating Range
Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/–) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
Do not mix different types of batteries or new and old batteries.
Note on Remote Control Operation:...

E – 14
Using Remote Mouse ReceiverThe remote mouse receiver enables you to operate your computer’s mouse functions from the remote control (Computer mode). It is a great
convenience for clicking through your computer-generated presentations.To return to the Projector mode, press the PJ button (lit red).
Connecting the remote mouse receiver to your computerIf you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer...

E – 15
Switching operation mode between computer and projectorThe three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.
In the Computer mode the PJ button is not lit.
•When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu
operation using the three buttons.
•When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the SELECT 
,...

E – 16
2. INSTALLATION
This section describes how to set up your LT158/LT157 projector and how to connect video and audio sources.
Setting up Your ProjectorYour LT158/LT157 Projector is simple to set up and use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you can project your image.
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the projector.
When...