NEC Lt10 Portable Projector Users Manual

								



1. Power Cord
2. VGA Cable
3. S-Video Cable
4. Composite Video Cable
Connecting the Projector
™To ensure the projector works well with your computer, please
set the display mode of your graphics card is less than or equal to
1024 X 768 resolution. Make sure timing of the display mode is
compatible with the projector.  Refer to the “Compatibility
Modes” section on page 30.
S-Video Output
Video Output
 1
23
4
Installation 
						

							





Installation
Lens capOn/Standby
 1
2
Powering On the Projector
1.Remove the lens cap.n
2.Ensure that the power cord and signal cable are securely
connected.
3.Turn on the lamp by pressing “On/Standby” button on the
control panel. o
The startup screen will display for 20 seconds and the Power
indicator will flash green.
When the startup screen disappears, the Power indicator will
turn green.
4.Turn on your source (computer, notebook, video player ,
etc.).  The projector will detect your source automatically.
™If the screen displays “No Signal”,  please make sure the signal
cables are securely connected.
™If you connect multiple sources at the same time, use the “Source”
button on the remote control or control panel to switch between them.
Powering On/Off the Projector
™Turn on the projector
first and then the
computer.     
						

							





Powering Off the Projector
1.Press the “Power” button to turn off the projector lamp.
2.After pressing the “Power” button, you will see a message
“Power off the lamp?” on the on-screen display. Press the
“Power” button again to confirm.
Otherwise the message will disappear after 5 seconds.
3.Power indicator flashes orange for about 100 seconds. The
projector will  automatically shut itself down.
If you want to turn on the projector again, you must press the
“Power” button after 100 seconds of the flashing indicator.
4.Disconnect the power cord from the electrical outlet and the
projector.
5.Do not turn on the projector immediately following a
power off procedure.
Status Indicator
™When the Status indicator turns red, it indicates the projector has
overheated. The projector will automatically shut itself down.
™When the Status indicator flashes red (0.5 second intervals), it
indicates a problem with the lamp.  Turn off the projector and
disconnect the power cord from the electrical outlet, then contact
your local dealer or our service center.
™When the Status indicator flashes red (1 second intervals), it
indicates an internal problem.  Stop using the projector and
disconnect the power cord from the electrical outlet, then
contact your local dealer or our service center.
™When the Status indicator flashes orange, it indicates high-speed
cooling in progress. This is not an abnormal condition, and you can
continue using the projector.
Installation 
						

							




Installation
Adjusting the Projected Image
Adjusting the Projector Height
Tilt Adjusted wheel
Adjustable Tilt
Foot
 1
2
3Adjustable Tilt
Foot Button
The projector is equipped with an adjustable tilt foot foot for
adjusting the projector height.
To raise the projector:
1.Press the adjustable tilt foot button 
n.
2.Raise the projector to the desired display angle o, then
release the button to lock the adjustable tilt foot into
position.
3.Use 
p to fine-tune the display angle.
To lower the projector:
1.Press the adjustable tilt foot button.
2.Lower the projector, then release the button to lock the
adjustable tilt foot into position.
3.Use 
p to fine-tune the display angle.   
						

							




. x a M) m c 4 . 1 8 (  1 . 2 3) m c 6 . 3 0 2 (  2 . 0 8) m c 3 . 9 3 3 (  6 . 3 3 1) m c 2 . 7 0 4 (  3 . 0 6 1) m c 0 . 3 4 5 (  8 . 3 1 2) m c 7 . 8 7 6 (  2 . 7 6 2
. n i M)m c 0 . 0 7 (  6 . 7 2)m c 1 . 5 7 1 (  9 . 8 6)m c 8 . 1 9 2 (  9 . 4 1 1)m c 2 . 0 5 3 (  9 . 7 3 1)m c 9 . 6 6 4 (  8 . 3 8 1)m c 7 . 3 8 5 (  8 . 9 2 2
) H x W ( . x a M 6 2 . 9 1 x  8 6 . 5 2
) m c 8 . 8 4 x m c 1 . 5 6 ( 2 1 . 8 4 x  6 1 . 4 6
) m c 2 . 2 2 1 x m c 9 . 2 6 1 ( 6 1 . 0 8 x  8 8 . 6 0 1
) m c 6 . 3 0 2 x m c 4 . 1 7 2 ( 8 1 . 6 9 x  4 2 . 8 2 1
) m c 3 . 4 4 2 x m c 8 . 5 2 3 ( 8 2 . 8 2 1 x  4 0 . 1 7 1
) m c 8 . 5 2 3 x m c 4 . 4 3 4 ( 2 3 . 0 6 1 x  6 7 . 3 1 2
) m c 2 . 7 0 4 x m c 0 . 3 4 5 (
) H x W ( . n i M 6 5 . 6 1 x  8 0 . 2 2
) m c 0 . 2 4 x m c 0 . 6 5 ( 4 3 . 1 4 x  2 1 . 5 5
) m c 1 . 5 0 1 x m c 1 . 0 4 1 ( 4 9 . 8 6 x  2 9 . 1 9
) m c 1 . 5 7 1 x m c 4 . 3 3 2 ( 4 7 . 2 8 x  2 3 . 0 1 1
) m c 1 . 0 1 2 x m c 2 . 0 8 2 ( 8 2 . 0 1 1 x  4 0 . 7 4 1
) m c 1 . 0 8 2 x m c 5 . 3 7 3 ( 8 8 . 7 3 1 x  4 8 . 3 8 1
) m c 2 . 0 5 3 x m c 0 . 7 6 4 (
) m 2 . 1 (  4 9 . 3) m 0 . 3 (  4 8 . 9) m 0 . 5 (  0 4 . 6 1) m 0 . 6 (  9 6 . 9 1) m 0 . 8 (  5 2 . 6 2) m 0 . 0 1 (  1 8 . 2 3
Focus Ring
Zoom Ring
Adjusting the Projector Zoom / Focus
You may adjust zoom ring to zoom in or out.  To focus the image,
rotate the  focus ring until the image is clear. The projector will
focus at distances from 3.94 to 32.81 feet (1.20 to 10.0 meters).
Adjusting Projection Image Size
68.9
(175.1cm) 114.9
(291.8cm) 137.9
(350.2cm) 183.8
(466.9cm) 229.8
(583.7cm)
32.1(81.4cm) 80.2(203.6cm) 133.6(339.3cm) 160.3 (407.2cm) 213.8(543.0cm) 267.2(678.7cm)
3.94
32.81 26.25 19.69 16.409.84(1.2m)
(10.0m)(8.0m) (6.0m) (5.0m) (3.0m) 27.6
(70.0cm)


	
	




	
™This graph is for user’s reference only.
Installation     
						

							




User Controls
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote
Control and Control Panel.
Using the Control Panel
On/Standby
Refer to the “Powering On/Off the Projector” section on pages
10-11.
Source
Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Menu
Press “Menu” to launch the on screen menu (OSM).  To exit
OSM, press “Menu” again.
Keystone   
Adjusts image distortion caused by tilting the projector (±16
degrees).
Directional Select
Use     to select items or use   to make adjustments for
your selection.
Enter
Confirm your selection of items.     
						

							




Using the Remote Control
Power
Refer to the “Powering On/Off the Projector” section on pages
10-11.
Source
Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
AUTO ADJ. (Auto Adjust)
When “AUTO ADJ.” is pressed, the projector will automatically
synchronize with source signal.
PiP
Displays the “PiP” menu of the on screen display.
Keystone +  / -
Adjust image distortion caused by tilting the projector (±16
degrees).
Hide
Press “Hide” to hide the image, press again to resume display of
the image.
Zoom In + /Zoom Out -
Press “Zoom +” to magnify an image on the projection screen.
Press “Zoom -” to reduce the image size.
Freeze
Press “Freeze” to pause the screen image.
Four Directional Select Keys
Use         to select items or make adjustments to
your selection.
Menu
Press “Menu” to launch the on screen menu (OSM).  To exit
OSM, press “Menu” again.
User Controls 
						

							




The Projector has multilingual On Screen menus that are
multilingual allowing you to make image adjustments and
change a variety of settings. The projector will automatically
detect the source.
How to operate
1.To open the OSM menu, press “Menu” on the Remote Control or
Control Panel.
2.When OSM is displayed, use     keys to select the main menu.
While making a selection on a particular page, press “Enter / 
”
key to enter sub menu.
3.Use      keys to select the desired item and adjust the
settings by 
    key.
4.Select the next item to be adjusted in the sub menu and adjust as
described above.
5.Press “Menu” to confirm, and the screen will return to the main
menu.
6.To exit, press “Menu”again.  The OSM menu will close and the
projector will automatically save the new settings.
On Screen Menus
User Controls
Main MenuSub MenuSetting     
						

							




Language
Language
You can display the multilingual OSM menu . Use the   or 
key to select your prefered language.
Press “Menu” to finalize the selection.

	
	
	

User Controls   
						

							




User Controls
All Images
Brightness
Adjusting the brightness of the image.
Press the  to darken image.
Press the  to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
Press the  to decrease the contrast.
Press the  to increase the contrast.
White Peaking
White peaking can be incrementally adjusted between 0 and
10.  Click on the slider bar to adjust.
Setting 10 will maximize brightness and contrast.
Setting 0 will maximize color reproduction quality.
Color Temperature
Adjust the color temperature. At higher temperature, the screen
looks colder; at lower temperature, the screen looks warmer.
Keystone
Adjusts image distortion caused by tilting projection (±16
degrees).
Zoom

Press the  to reduce the size of an image.
Press the  to magnify an image on the projection screen.