NEC Lt10 Portable Projector Users Manual

	



All Images
Aspect Ratio
Selects the desired aspect ratio.
Reset This Menu
Choose “Yes” to return the display parameters on this menu to
their factory default settings.

	
	
	

User Controls   






User Controls
Computer Image
Auto Adjust
The projector automatically adjusts clock, phase, horizontal
and vertical. With most signal sources, Auto Adjust provides the
best results.
Clock
“Clock”changes the display data frequency to match the
frequency of your computer’s graphic card. If you experience a
vertical flickering bar, use this function to make an adjustment.
Phase
“Phase” synchronizes the signal timing of the display with the
graphic card. If you experience an unstable or flickering...






Video Image

	

Color
Adjusts a video image from black and white to fully saturated
color.
Press the  to decrease the amount of color in the image.
Press the  to increase the amount of color in the image.
Sharpness
Adjusts the sharpness of the image.
Press the  to decrease the sharpness.
Press the  to increase the sharpness.
Hue
Adjusts the color balance of red and green.
Press the  to increase the amount of green in the image.
Press the  to increase the amount of red  in the...





User Controls
Menu Location
Choose the Menu location on the display screen.
Orientation

Front-Desktop
The factory default setting.
Rear-Desktop
When you select this function, the projector reverses the image
so you can project behind a translucent screen.
Front-Ceiling
When you select this function, the projector turns the image
upside down for ceiling-mounted projection.
Rear-Ceiling
When you select this function, the projector reverses and turns
the image upside down at same time. You...





Setup

	
	
	

User Controls
Factory Default
Choose “Yes” to return the display parameters (except for Lamp
Hours) on all menus to their factory default settings.   





PIP
PIP
Choose “On” to turn the PIP screen on.
PIP Location
Choose the PIP screen position on the display screen.
PIP Switch Source
Choose the input source of the projector on the PIP screen.
Reset This Menu
Choose “Yes” to return the display parameters on this menu to
their factory default settings.

	

™The OSM does not
include a PIP menu
under Video mode.
User Controls
Picture-In-Picture     





Appendices
Problem: No image appears on screen.
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Changing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Problem: Partial, scrolling or incorrectly displayed image.
Press the “Auto...





Appendices
4.Follow above steps 1-2. Click on the “Advanced Properties”
button.
5.Select the “Change” button under the “Monitor” tab .
6.Click on “Show all devices”. Then select “Standard monitor
types” under the “Manufactures” box ; choose the resolution
mode you need under the “Models” box.
7.Verify that the resolution setting of the monitor display is less
than or equal to 1024 x 768.
If you are using a Notebook PC:
1.You are required to implement above steps of resolution setting
of...





Problem: Image is out of focus
Adjusts the Focus Ring on the projector lens.  Refer to page 13.
Make sure the projection screen is between the required distance
3.94 to 32.81 feet (1.20 to 10.00 meters) from the projector.
Problem: The image is outstretched when displaying 16:9
DVD.
The projector automatically detects 16:9 DVD and adjusts the aspect
ratio by digitizing to full screen with 4:3 default setting.
If the image is still outstretched, you will also need to adjust the aspect
ratio...





Appendices
Changing the lamp
The projector will detect the lamp life itself.  It will show you a
warning message “The Lamp has been in use for over 2000
hours.  You should purchase a spare bulb.” When you see this
message, please change the lamp as soon as possible. Refer to the
following instructions to replace the lamp.
Make sure the projector has been cooled down for at least 60
minutes before changing the lamp.
Warning: Lamp
compartment is hot!
Allow it to cool down
before changing lamp!...