NEC Ht410 Entertainment Projector Users Manual

E-vi
TABLE OF CONTENTS
Information ................................................................................................................................................................................................... E-43
Page 1/2/3 ................................................................................................................................................................................................ E-43
Reset...

E-1
1. INTRODUCTION
1. INTRODUCTION
Introduction to the ProjectorThis section introduces you to your new NEC HT510/HT410 home entertainment Projector and describes its
features and controls.
Congratulations on Your Purchase of The HT510/HT410 Entertainment Projector
The HT510/HT410 is a sophisticated single chip DLP™ projector designed with the enhanced video require-
ments for the home entertainment user.  With the HT510/HT410 you will enjoy projecting images up to 200”
(measured diagonally) from your...

E-2
About this users manual
The fastest way to get started is to take your time and do everything right the first time. Take a few
minutes now to review the users manual. This may save you time later on. At the beginning of each
section of the manual youll find an overview. If the section doesnt apply, you can skip it.
•Digital Light Processing and DLP are trademarks of Texas Instruments.
•IBM is a trademark or registered trademark of International Business Machines Corporation.
•Mac and PowerBook are...

E-3
Part Names of the Projector
1. INTRODUCTION
C
O
N
T
R
O
L
CO
MPONENT IN COMPUTER INVIDEO
 IN AU
DIO IN
S
-V
ID
E
O
 IN
R Cr/Pr Cb/Pb
Y
L/mono
AUDIO
 IN
S
E
L
E
C
T
LAMP
STATUS
POWER
ON/STAND BY
A
U
T
O
A
D
J
.
AC IN
LENS SHIFTU
PSELECT
LAMP
STATUS
POWER
ON/STAND BY
A
U
T
O
A
D
J
.SOURCE
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc. Remote Sensor (See page...

E-4
Top Features
LAMP
STATUS
POWER
SOURCE
AUTO
ADJ.ON/STAND BY
SELECT
3
24
5
87
16910
1. INTRODUCTION
1. ON/STAND BY button (  )
Use this button to turn the power on and off when the main power is supplied and the projector is in standby
mode.
To turn on the projector, press and hold this button for a minimum of two seconds. To turn off the projector,
press this button twice.
2. POWER indicator
When this indicator is green, the projector is on; when this indicator is orange, it is in standby mode. See...

E-5
Terminal Panel Features
1. COMPUTER IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM compatible or Macintosh computers.
Use the supplied RGB/VGA cable to connect to your computer. This also serves as a component input con-
nector that allows you to connect a component video output of component equipment such as a DVD player
(optional adapter ADP-CV1 required).
2. AUDIO IN mini jack (Stereo Mini)
This is where you connect the audio...

E-6
Part Names of the Remote Control
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector cabinet.
2. POWER ON Button
When the main power is on, you can use this button to turn your projector on.
NOTE: To turn on the projector, press and hold the POWER ON button for a minimum of two seconds.
3. POWER OFF Button
You can use this button to turn your projector off.
NOTE: To turn off the projector, press the POWER OFF button twice.
4. VIDEO  Button
Press this button to...

E-7
1. INTRODUCTION
7. COMP. Button (COMPUTER)
Press this button to select a video source from computer or component equipment connected to your COM-
PUTER IN port.
8. AUTO Button (AUTO ADJ.)
Use this button to adjust an RGB source for an optimal picture. See page E-27.
9. SELECT 
 Button

 : Use these buttons to select the menu of the item you wish to adjust.
 : Use these buttons to change the level of a selected menu item.
10. MENU Button
Displays the menu for various settings and adjustments....

E-8
Battery Installation
1Press firmly and slide the battery cover off.
2Remove both old batteries and install new ones
(AAA). Ensure that you have the batteries polarity
(+/–) aligned correctly.
3
Remote Control Precautions
•Handle the remote control carefully.
•If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
•If you will not be using the remote control for a long time, remove the batteries.
•Do not place the batteries upside down.
•Do not use new and old...

E-9
1. INTRODUCTION
30º
30º
Remote sensor on projector cabinet
Remote control
7m/22 feet
•The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree
angle of the remote sensor on the projector cabinet.
•The projector will not respond if there are objects between the remote control and the sensor, or if strong light
falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
Operating Range for Wireless...