NEC Gt6000r Lcd Projector Users Manual
Have a look at the manual NEC Gt6000r Lcd Projector Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
10-9 n Compatible Input Signal List Signal Resolution Frequency H. Refresh Rate ( Dots ) ( kHz ) ( Hz ) NTSC – 15.734 60 PAL – 15.625 50SECAM – 15.625 50VESA 640480 31.47 59.94 IBM 640480 31.47 60MAC 640480 31.47 60MAC 640480 34.97 66.67 MAC 640480 35 66.67VESA 640480 37.86 72.81VESA 640480 37.5 75 IBM 640480 39.375 75VESA 640480 43.269 85.01IBM 720350 31.469 70.09 VESA 720400 37.927 85.04IBM 720350 39.44 87.85IBM 720400 39.44 87.85 VESA 800600 35.16 56.25VESA 800600 37.879 60.32VESA 800600 48.077 72.19 VESA 800600 46.88 75VESA 800600 53.674 85.06MAC 832624 49.725 74.55 VESA 1024768 35.5 43 InterlacedVESA 1024768 48.363 60VESA 1024768 56.476 70.07 MAC 1024768 60.241 74.93VESA 1024768 60.023 75.03VESA 1024768 68.677 85 # VESA 1152864 67.5 75# MAC 1152870 68.681 75.06# SUN 1152900 61.796 65.95 # SGI 1152900 71.736 76.05# VESA 1280960 60 60# VESA 12801024 63.981 60.02 # MAC 12801024 69.89 65.2# HP 12801024 78.125 72.01# SUN 12801024 81.13 76.11 # VESA 12801024 79.976 75.03# VESA 12801024 91.146 85.02# SXGA+ 14001050 – – #@ HDTV (1080p)19201080 67.5 60SDTV(576i)(625i)– 15.6 50SDTV(576p)(625p)– 31.5 50 #@ HDTV (1080i)(1125i)19201080 33.75 60 Interlace#@ HDTV(1080i)(1125i)19201080 28.13 50 Interlace#HDTV (720p)(750p)1280720 45 60 Progressive SDTV (480p)(525p)– 31.47 59.94 Progressive# @ VESA 16001200 75.0 60# @ VESA 16001200 81.3 65 # @ VESA 16001200 87.5 70# @ VESA 16001200 93.75 75DVD YCbCr – 15.734 59.94 Interlaced DVD YCbCr – 15.625 50 Interlaced #: Images in above flagged with # are compressed with Advanced AccuBlend on GT5000. @: Images in above flagged with # are compressed with Advanced AccuBlend on GT6000. NOTE: Some composite sync signals may not be displayed correctly. Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures. UXGA (16001200) is supported for separate sync signal only. 10. Appendix
10-10 m REMOTE 1 Connector 51423 10 11 12 13 14 156 978 This connector is used for a third party external control device. Pin No. 14 5 10 3 4,8,12,11SHORT/OPEN SHORT OPEN SHORT OPEN SHORT OPEN SHORT OPENFUNCTION External control mode ON External control mode OFF POWER ON POWER OFF PICTURE MUTE ON PICTURE MUTE OFF MUTE SOUND ON MUTE SOUND OFF * When combinations other than specified in the above table are selected or when no optional board is inserted in the Slot 1 and 2, the input will be switched to RGB 1 by default. * The term “SHORT” means to connect with pin 15 * When in the external control mode, the POWER, Source/Input, PICTURE MUTE and SOUND MUTE buttons on the remote control will not function. * When the External control mode is set to ON, the following settings are not effective: Source Select, Auto Start, Power Management, Power off Confirmation, Idle mode, Default Source Select, Timer and Test Pattern. NOTE: When turning off the power to the projector using the external control, do not disconnect the plug from the power outlet.Theseprocedures are to protect your projector and the connected equipment. 11pin OPEN OPEN OPEN OPEN OPEN OPEN OPEN SHORT SHORT SHORT SHORT SHORT SHORT12pin OPEN OPEN OPEN SHORT SHORT SHORT SHORT OPEN OPEN OPEN SHORT SHORT SHORT8pin OPEN OPEN SHORT OPEN OPEN SHORT SHORT OPEN OPEN SHORT OPEN OPEN SHORT4pin OPEN SHORT OPEN OPEN SHORT OPEN SHORT OPEN SHORT SHORT OPEN SHORT OPENRGB 1 VIDEO S-VIDEO Slot 1-1 RGB 2 Slot 1-2 RGB1 (S-VIDEO) DVI (DIGITAL) VIEWER RGB1 (VIDEO) Slot 2-1 Slot 2-2 LAN 10. Appendix
10-11 15243 67 98 Cable Connection Communication Protocol Baud rate ........................ 38400 bps Data length ..................... 8 bits Parity .............................. No parity Stop bit ........................... One bit X on/off ........................... None Communications procedure Full duplex NOTE: Depending on the equipment, a lower baud rate may be recommended forlong cable runs. , PC Control Codes and Cable Connection PC Control CodesFunction Code Data POWER ON 02H 00H 00H 00H 00H 02H POWER OFF 02H 01H 00H 00H 00H 03H INPUT SELECT RGB 1 02H 03H 00H 00H 02H 01H 01H 09H INPUT SELECT RGB 2 02H 03H 00H 00H 02H 01H 02H 0AH INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H LAN 02H 03H 00H 00H 02H 01H 20H 28H SLOT1-1 02H 03H 00H 00H 02H 01H 24H 2CH SLOT1-2 02H 03H 00H 00H 02H 01H 25H 2DH SLOT2-1 02H 03H 00H 00H 02H 01H 29H 31H SLOT2-2 02H 03H 00H 00H 02H 01H 2AH 32H RGB1(VIDEO) 02H 03H 00H 00H 02H 01H 07H 0FH RGB1(S-VIDEO) 02H 03H 00H 00H 02H 01H 0CH 14H PICTURE MUTE ON 02H 10H 00H 00H 00H 12H PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H SOUND MUTE ON 02H 12H 00H 00H 00H 14H SOUND MUTE OFF 02H 13H 00H 00H 00H 15H ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H NOTE: Contact your local dealer for a full list of PC Control Codes if needed. . Using Software Keyboard 1 to 0 and Characters ........................ Use to type in IP address or projector name MODE .............Selects one of three modes for alphabet and spe- cial characters. SP ................... Inserts a space BS ................... Deletes one character backward ..................... Returns to the previous ..................... Advances to the next OK ................... Executes the selection Cancel ............. Cancels the selection To GND of PC NOTE: Pins 1, 4, 6 and 9 are no used. NOTE: Jumper “Request to Send” and “Clear to Send” together on both ends of thecable to simplify cable connection.To RxD of PC To TxD of PC To RTS of PC To CTS of PC PC Control Connector (D-SUB 9P) 10. Appendix
10-12 ⁄0 Operation Using an HTTP Browser Overview The use of HTTP server functions will allow control of the projec- tor from a web browser without the installation of special soft- ware. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will vary depending on the version of browser. Please refer to the help files and the other informa- tion provided in your software.) NOTE: * The use of HTTP server functions is not available during Standby mode. * The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your network. Should this happen, consult your network administrator. * The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and repeat. If you still can’t get any response, pull out and then re-insert the LAN card. * Do not use the HTTP Server functions and the Dynamic Image Utility included on the supplied CD-ROM. Using both at the same time may result in a connection failure or slow response. Access is gained to the HTTP server functions by specifying http:// /index.html in the entry column of the URL. Preparation Before Use Make network connections and set up the projector and confirm that it is complete before engaging in browser operations. (See “LAN Mode” on page 8-19.) Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be dis- played depending on the effectiveness of the cache, and the con- tents set from the browser may not be reflected in operation. It is recommended that a proxy server not be used unless it is un- avoidable. Handling of the Address for Operation via a Browser Regarding the actual address that is entered for the address or entered to the URL column when operation of the projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the projector has been registered to the domain name server by a network administra- tor, or the host name corresponding to the IP address of the pro- jector has been set in the “HOSTS” file of the computer being used. Example 1:When the host name of the projector has been set to “pj.nec.co.jp”, http://pj.nec.co.jp/index.html is specified for the address or the entry column of the URL. Example 2: When the IP address of the projector is “192.168.73.1”, access is gained to the HTTP server func- tions by specifying http://192.168.73.1/index.html for the address or the entry column of the URL. Structure of the HTTP Server Power: This controls the power of the projector. On ............... Power is switched on. Off ............... Power is switched off. Volume: This controls the volume of the projector. ................. Increments the volume adjustment value. ................. Decrements the volume adjustment value. Mute: This controls the mute function of the projector. All On .......... Mutes each of the video, audio, and on-screen display functions. All Off .......... Cancels the muting of each of the video, audio, and on-screen display functions. Picture On ... Mutes the video. Picture Off ... Cancels the video muting. Sound On .... Mutes the audio. Sound Off .... Cancels the audio muting. OSD On ....... Mutes the on-screen display. OSD Off ....... Cancels the muting of the on-screen display. Picture: Controls the video adjustment of the projector. BrightnessIncrements the brightness adjustment value. BrightnessDecrements the brightness adjustment value. Contrast ... Increments the contrast adjustment value. Contrast ... Decrements the contrast adjustment value. Color........ Increments the color adjustment value. Color........ Decrements the color adjustment value. Hue.......... Increments the hue adjustment value. Hue.......... Decrements the hue adjustment value. Sharpness Increments the sharpness adjustment value. Sharpness Decrements the sharpness adjustment value. * The functions that can be controlled will vary depending on the signal being input to the projector. 10. Appendix
10-13 Source Select: This switches the input connector of the projec- tor. RGB1 ...................... Switches to the RGB 1 connector. RGB2 ...................... Switches to the RGB 2 connector. DVI(DIGITAL) ........... Switches to the DVI connector. Video ....................... Switches to the Video connector. S-Video ................... Switches to the S-Video connector. Viewer ..................... Switches to the Viewer. LAN ......................... Switches to a LAN signal. Slot 1-1 .................... Switches to input 1 of the Slot 1. Slot 1-2 .................... Switches to input 2 of the Slot 1. Slot 2-1 .................... Switches to input 1 of the Slot 2. Slot 2-2 .................... Switches to input 2 of the Slot 2. RGB1 (VIDEO) ........ Switches to Video of the RGB1 connec- tor. RGB1 (S-VIDEO) .... Switches to S-Video of the RGB1 con- nector. Projector Status: This displays the condition of the projector. Remaining Lamp 1/2 Time ................................ Displays the remaining life of lamps 1/2 as a percentage. Lamp 1/2 Hour Meter ...Displays how many hours lamps 1/2 have been used. Projector Usage ...... Displays how many hours the projector has been used. Filter Usage ............. Displays how many hours the filter has been used. Error Status ............. Displays the status of errors occurring within the projector. Refresh .................... Updates the display of the following con- ditions. 10. Appendix Ver. 3 5/03
NEC SOLUTIONS’ PROJECTOR PRODUCTSNEC Solutions (America), Inc. (hereafter NEC Solutions) warrants this product to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTYNEC Solutions’ GT6000/5000 projectors are covered by a two (2) year limited parts and labor warranty from the date of the first customer purchase. The lamp when used under normal operating conditions is warranted for 500 hours or 90 days, whichever comes first. WHO IS PROTECTEDThis warranty may be enforced only by the first purchaser, and is not transferable. WHAT IS COVERED AND WHAT IS NOT COVEREDExcept as specified below, this warranty covers all defects in material or workmanship in this product. NEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT NEC SOLUTIONS’ OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR ‘LIKE NEW’. The following are not covered by the limited warranty and NEC Solutions shall not be liable for: 1. Any product which is not distributed in the U.S.A. or Canada by NEC Solutions or which is not purchased, installed, and operated in the U.S.A or Canada. 2. Any product on which the serial number has been defaced, modified or removed. 3. Normal decrease in lamp light output over time. 4. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, improper ventilation, fire, dust, smoke, water, lightning or other acts of nature, unau- thorized product modification, or failure to follow instruc- tions supplied with the product. b. Repair or attempted repair by anyone other than a NEC Solutions authorized service center. c. Any shipment of the product (claims must be presented to the carrier). d. Removal or installation of the product. e. Any other cause which does not relate to a product defect. f. Use of the product beyond normal operating conditions. Normal operating conditions are defined as product use not in excess of 8 hours per day and 260 days per year. 5. Cartons, carr ying cases, shipping cases, batteries, external cabinets, magnetic tapes, or any accessories used in connec- tion with the product. 6. Service required as a result of third party components. WHAT NEC SOLUTIONS WILL PAY FORNEC Solutions will pay labor and material expenses for covered items, but NEC Solutions will not pay for the following: 1. Removal or installation charges. 2. Costs of technical adjustments, set-up, maintenance, or adjust- ment of user controls. 3. Payment of shipping and related charges incurred in returning the product for warranty repair. LIMITED WARRANTY (USA and Canada only) HOW YOU CAN GET WARRANTY SERVICE1. To obtain ser vice on your product, consult the dealer from whom you purchased the product. 2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage. In order to obtain warranty ser vice, you may be required to describe and demonstrate the problem to your dealer or to NEC Solutions. 3. All products returned to NEC Solutions for service MUST have prior approval. To receive approval or for the name of the nearest NEC Solutions authorized service center, call NEC Solutions at 800-836-0655. 4. It shall be your obligation and expense to ship the product, freight prepaid, or to deliver it to a NEC Solutions authorized service center, in either the original package or a similar pack- age affording an equal degree of protection. 5. In the event a product is returned to NEC Solutions for warranty service, and it is determined that there is no product defect or that the product condition is not covered by this limited warranty, a diagnostic service fee may be charged to the customer. LIMITATION OF IMPLIED WARRANTIESEXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY, NEC SOLUTIONS MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED WARRAN- TIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS AND DURATION OF THIS LIMITED WARRANTY. EXCLUSION OF DAMAGESNEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT NEC SOLUTIONS’ OPTION. NEC SOLUTIONS SHALL NOT BE LIABLE FOR: 1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THIS PRODUCT, DAMAGES BASED UPON INCONVE- NIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, COMMERCIAL LOSS; OR 2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSE- QUENTIAL OR OTHERWISE. HOW STATE LAW RELATES TO THE WARRANTYSOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN- TIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLU- SIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. FOR MORE INFORMATION, CONTACT: NEC SOLUTIONS (AMERICA), INC. 1250 N. Arlington Heights Road, Suite 400 Itasca, Illinois 60143-1248 TELEPHONE 800-836-0655 www.necvisualsystems.com Customers are cautioned that product performance is affected by system configuration, software, the application, customer data, and operator control, among other factors. While NEC Solutions’ products are considered to be compatible with many systems, the specific functional implementation by the customers of the prod- uct may vary. Therefore, the suitability of a product for a specific purpose or application must be determined by the customer and is not warranted by NEC Solutions. Printed in Japan Printed on recycled paper
DECLARATION OF CONFORMITY U.S. Responsible Party: Address: Tel. No.:NEC Solutions (America), Inc. 1250 N. Arlington Heights Road Itasca, Illinois 60143 (630) 467-5000 Type of Product: Equipment Classification: Model:LCD Projector Class B Peripheral GT6000/GT5000 We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.