NEC 1200c Manual

31
4. Using Menus
When not displaying menus, the following screen is normally displayed.
When in standby
When the projector is in a standby state (the projector power switch is on), the following is displayed.
When power is turned on
When the power is turned on, the following is displayed.
← Displays the hours of lamp bulb use. 
←  Displays the lamp output (%). 
←  Displays the selected title. 
←  Displays the selected port. 
When the power is turned off
The amount of time remaining for cooling is...

32
4. Using Menus
4-1-2. Operating menus
Preparation: Turn your projector on. (See page 20)
1Press the MENU button on the control panel of your projector .
The menu is displayed in the LCD screen.
2Press the LEFT/RIGHT buttons to display “Information.”
At each press of the LEFT/RIGHT buttons, the display will cycle as “Title Selec\
t” ←→ “Configuration”  ←→ “(Title Setup)”
←→  “Information.”
3Press the DOWN button.
The submenu “Lamp” of “Information” is displayed.
The menu item can be selected by...

33
4. Using Menus
6Press the DOWN button.
The submenu “BIOS” another rank lower than “System” is displ\
ayed.
7Press the LEFT/RIGHT button to select the submenu “Data.”
At each press of the LEFT/RIGHT button, the display will cycle as “BIOS” ←→ “Firmware”  ←→ “Data”  ←→ “Lens”  ←→
“Serial No.”  ←→ “Model,” and each version information is displayed.
8Press the UP button several times.
At each press of the UP button, the display will return to a menu one level above. 

34
4. Using Menus
4-1-3. How to enter alphanumeric characters
Alphanumeric characters are entered for items, such as the title of input signal.
Characters can be entered by pressing numeric buttons on the control panel on this projector.
1
2
3
45
LAMP MENU ENTERDOUSER
KEY
LOCK
EXIT
IMB
6
7
8
Enter characters
Delete entered characters
Move right and left
Characters can be entered by pressing each button as shown in the following table.
• To delete a character during entry, press the DOWN button.
[Example...

35
4. Using Menus
4-2. Table of adjustment menus
Menus in parentheses are menus for our service personnel. Normally, these menus cannot be used.
Main menu Submenu DescriptionReference page
Title Select “Title Memory Name” Selects the title of the signal to be projected.  36 TEST Pattern Selects the test pattern to be projected.  36 37
37
Configuration Lamp Setup Adjust Adjusts lamp brightness. 
Feedback Sets the lamp brightness constant mode that uses a brightness sensor. 
Lens Control Lens Position...

36
4. Using Menus
4-3. Title Select
4-3-1. Title select (Title Memory)
Selects the title of the signal to be projected.
You can register up to 100 titles. You can also assign registered titles to the preset buttons ( to  buttons) on the
projector’s control panel and call them up directly using those buttons.
Request your dealer/distributor for details on registering and changing titles.
←  Displays the currently selected item with asterisk (*).
←  Selects the title to be projected. 
4-3-2. Test Pattern...

37
4. Using Menus
4-4. Configuration
Please request your dealer/distributor to perform the settings.
4-4-1. Lamp Setup
Adjust
Adjusts the lamp output (brightness). Control the output at 10 W increments.
← Displays the lamp output (%) with regard to the setting. 
←  Adjusts the lamp brightness. 
Feedback
Sets the lamp brightness constant mode that uses a brightness sensor.
Disable
EnableDisables the lamp brightness constant mode. 
Enables the lamp brightness constant mode. 
←  Displays the currently...

38
4. Using Menus
4-5. Title Setup
Sets the title to be assigned to the preset buttons ( to  buttons).
Request your dealer/distributor to perform the settings.
4-6. Information
Displays the hours of lamp bulb use, the version information and error codes.
4-6-1. Lamp
Displays information relating to the lamp. (Such as lamp output and the information of lamp bulb.)
Output
Displays the lamp brightness (output) setting.
← Displays the set current (A). 
←  Displays the power consumption (kW). 
Bulb Type [A]...

39
4. Using Menus
4-6-2. Preset Button
Sets the title to be assigned to the preset buttons ( to  buttons) on the projector’s control panel.
← Selects the preset button number whose contents you want to display.
←  Displays the assigned title numbers.
←  Displays the registered names of the assigned titles.
4-6-3. Usage
Displays the hours of projector head, lamp, and lamp house usage, and warning display time of the lamp bulb.
Projector
Bulb
Lamp house
Bulb Warning
AC On Fan
Power On Fan
Lamp Fan...

40
4. Using Menus
4-6-5. Version
Displays the versions of the projector head, and the multi-media switcher (MMS) (optional).
System
Displays the version information of the projector head.
BIOS
Firmware
Data
Lens
Serial No.
ModelDisplays the BIOS version of the projector head. 
Displays the firmware version of the projector head. 
Displays the data version of the projector head. 
Displays the firmware version of the lens mount on the projector.
Displays the serial number of the projector head. 
Displays...