Namco Ridge Racer Upright Operators Manual

Operators Manual
RIDGE RACER
UPRIGHT
Part No 90500009
TM 

© Ltd - all rights reserved.
No part of this publication may be reproduced by any mechanical, photographic or
electronic process, or in the form of phonographic recording, nor may it be stored in a
retrieval system, transmitted or otherwise copied for public or private use, without
permission from 
namco Ltd.
Published by:
BRENT LEISURE Ltd.
Unit 1 Brent Crescent,
London. NW10 0QT
Phone:- 081-965-0550
Fax:- 081-961-0574 

Contents
Operators Manual ................................................................................... 1
1. SPECIFICATIONS ............................................................................ 4
2. PRECAUTIONS ................................................................................ 5
2-1 Cautions When Installing..................................................................... 5
2-2 Caution when Handling........................................................................ 5...

Page 4
1. SPECIFICATIONS
POWER SUPPLY :- 220/240volts AC
MONITOR:- Hantarex 26 Polo Colour Monitor with auto
degause 
DIMENSIONS :- 1205(w) x 895(d) x 1900(h)
WEIGHT :- 140kg.
ACCESSORIES :- Keys: (Cash Door).................................. 2
(Coin Assy) ................................... 2
((Back Door) ................................. 2
Operators Manual ......................................... 1
IEC Mains Lead ............................................. 1 

Page
2. PRECAUTIONS
2-1 Cautions When Installing.This game is designed for indoor use only. The game must not be installed outdoors or
under the following conditions:- 
a. In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat or extreme cold.
b. In locations that would present an obstacle in the case of an emergency, ie. near fire equipment or emergency exits.
c. On an unstable surface or subject to floor vibration.
2-2 Caution when Handling. a. AC power must always...

Page 6
3. ADJUSTMENTS
3-1 Turning on the Power
After installing the product,  turn on the power.  The power switch is located 
above the mains inlet on the rear of the main body.
3-2 Switches for Adjustments Open the coin door to find the switches for adjustments. 
1. Service switch.
Press this switch to increase the number of credits without incrementing\
 thecoin counte r.
2. Test switch.
Set this switch to “ON” to enter test mode. 
You can change the game fee and so on,  and perform various tests in...

Page 7
3-3 Test Mode
1. Open the coin door,  then set the test switch to “ON”.  The “Menu Screen” appears on the monitor display.
2. Select the item to be tested by turning the steering wheel right or left\
. The colour of the item you selected changes.
3. Step on the accelerator pedal to display the menu of the selected item. To return to the “Menu Screen”,  step on the brake pedal (step on b\
oth 
the brake and clutch pedals on the Switch Test Screen).
4. When the test finishes,  set the test switch to...

Page 8
3-3-1 Setting the Game Fee and So On (On the Coin Options Screen)
Select 1 “COIN OPTIONS” on the Menu
Screen to set the game fee and so on.
Turn the steering wheel to select 
the item to be changed,  then
step on the accelerator pedal. 
Turn the steering wheel again to 
change the setting,  then step on
the accelerator pedal (See table
1.) 
Step on the brake pedal to return 
to the Menu Screen.
Note: The price of play
adjustments aremade on the creditboard and the coin options should be set as the...

Page 9
GAME OPTIONS
(DEFAULT IN GREEN)
GAMEDIFFICULTYTIMEEXTEND
NOVICE D** ** ** (a)
ADVANCED D** ** ** (b)
EXPERT D** ** ** (c)
T.T. D** ** ** (d)
LAP
NOVICE 2(e)
ADVANCED 3(f)
EXPERT 3(g)
T.T. 3(h)
SPEEDKM/H(i)
SOUND    IN    ATTRACT
ON(j)
EXIT  =  STEP ON THE BRAKE
ItemDescriptionFactory setting
(a) Play time for the novice levelA (shortest) to H (longest)D
(b) Play time time for the advanced levelA (shortest) to H (longest)D
(c) Play time for the expert levelA (shortest) to H (longest)D
(d) Play time...

3-3-3 Switch TestSelect 3 “SWITCH TEST” to display the following screen. 
a. The status of the option switch SW2 on the game PCB (CPU-PCB) is indicated here.
b. The status of the option switch SW3 on the game PCB (CPU-PCB) is indicated here. 
The SW2 or SW3 switch is set to ON when the corresponding number
is red.
c. When you turn the steering wheel to the right,  the number increments. When turning it to the left,  the number decrements.
d. When you step on the accelerator pedal,  the number...