Namco Alpine Racer 52 Operators Manual

Page 13
5. INSTALLATION
WARNING If the location site of this machine has a polished floor it is recommended
that rubber pads are fitted under the level adjusters to prevent the
machine sliding on the floor.
5-1 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important that
at least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is very high, and it is important
that a means of reaching the height safely,...

Page 14 5-2 Connecting the Ski Assy to the Monitor Cabinet.
1. Connect the connectors between the Ski Assembly and Monitor Cabinet.
2. Push the Ski Assembly fully up to the monitor cabinet, taking care not to trap
any wires.
3. Fit, finger tight, a joint bracket to each side using 4off Hex Head Set Screws
(M10x25), Spring and Flat Washers on each bracket. Tighten fully all screws.
(Note: Joint Brackets are handed, ensure  bracket is fitted with fixing holes
uppermost.) 

Page 15
2. Place the assembled Safety Mat into position under the Ski Step Assy.
3. Retain the Safety Mat in position with the Hex Head Set Screws (M8x20), Spring
Washers and Flat Washers
5-3 Fitting the Safety Mat
1. Assemble the Floor Safety Mat by fitting the securing plates from underneath,
the support brackets from the top and retaining the assembly together with
the M6 Dome Nuts.
NOTE:-
When the machine is fully assembled and in its final position, lower the 10 level
adjusters, (4 on the monitor...

Page 16
Service Bracket
COIN COUNTER
TEST SERVICE TEST SERVICERIGHT PLAYER
LEFT PLAYER
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power switch is 
located on the rear of the monitor cabinet.
6-2 Adjustment Switches The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play m\
eter.
2. Test Switch Slide the test switch ON to enter test mode. 
Test mode allows...

Page 17
MENU
COIN OPTIONS ----------------- (1) Sets the price of play  (See 6-3-1)
GAME OPTIONS ----------------- (2) Sets the game options  (See 6-3-2)
I/O TEST ----------------- (3) Used for testing switches and controls -----------------(See 6-3-3)
SOUND TEST ----------------- (4) Used for testing sound and setting ----------------- volumes  (See 6-3-4)
MONITOR TEST ----------------- (5) Used for adjusting the monitor 
ADS TEST ----------------- (6) Displays accumulated game data
OTHERS...

Page 18COIN OPTIONS
[ DEFAULT IN GREEN ]
GAME COST
1 COIN 1 CREDIT ------------------------ (a)
FREE PLAY OFF ------------------------ (b)
EXIT
SELECT L/R BUTTON : CHOOSE
DECISION BUTTON : CHANGE +
6-3-1 Coin Options
1. Select item (1) COIN
OPTIONS on the
menu screen to set
the game cost and
related settings.
2. Press Select L/R to
select the required
item.
3. Use the Decision
button to adjust the
settings.
4. Select EXIT to
return to the menu
screen.
Note :- The price of play on this machine is set...

Page 19 6-3-2 Game Options
1. Select item (2) GAME OPTIONS on the menu screen to set the game
options and related settings.
2. Press Select L/R to select the required item.
3. Press the Decision button to adjust the settings. Standard settings are
displayed in green.
4. Select EXIT and press Decision to return to the menu screen.
GAME OPTIONS
[ DEFAULT IN GREEN ]
GAME DIFFICULTY B ------------ (a)
SOUND IN ATTRACT ON ------------ (b)
HI SCORE INITIALIZE NO ------------ (c)
AUTO HIGH SCORE INITIALIZE OFF...

Page 20
I/O TEST
DIP 4 12345678 ............................ (a) 
SWITCH TEST ............................ (b) 
MOTOR TEST ............................ (c)
STEP ADJUST ............................ (d)
EXIT
SELECT L/R BUTTON : CHOOSE DECISION BUTTON : ENTER
6-3-3 I/O Test
1. Select item (3) I/O Test on the menu screen to test the switches, motorand step adjust.
2. Press Select L/R to select the required item, then press the Decision\
 button to enter the test.
3. Select EXIT and press the Decision button...

Page 21
6-3-3-1 Switch Test
1. Select Switch Test from the I/O Test menu. The following screen willappear on the monitor.
Note:- On entering Switch T est the Skis will be unlocked. Ensure that the
Skis are returned to the locked condition at the end of the test by entering Motor T est (See 6-3-3-2)
SWITCH TEST
TEST SW ON ................. (a) 
COIN SW ON ................. (b)
SERVICE SW ON ................. (c)
R SELECTION BUTTON ON ............ (d)
DECISION BUTTON ON ............ (e)
L SELECTION BUTTON...

Page 22 6-3-3-2 Motor Test
1. Select Motor Test from the I/O Test menu. The following screen will
appear on the monitor.
MOTOR TEST
NOW MOTOR STATE : LOCK ............ (a)
GO MOTOR : FREE ................. (b)
EXIT
L/R SELECT BUTTON : CHOOSE
DECISION BUTTON : EXIT
(a) Displays the current condition of the Skis.
Display will show LOCK - FREEING - FREE - LOCKING as the Skis
are tested.
(b) Allows the Skis to be locked and unlocked.
Display will show FREE - NOW  MOVING - LOCK as the Skis are
being tested....