Multi-Tech Systems MultiVOIP200 Upgrade Information Manual

							1
MultiVOIP200 Upgrade Caution
Product Update
1/12/01
Part Number: 82095117, Rev. C
Important read before installation: MultiVOIP200s with H.323 compatible firmware (MVP200
version 2.50 or later) are not compatible with MultiVOIPs using earlier proprietary versions of firmware. Also, the
MultiVOIP200s with H.323 compatible firmware will not operate behind non-H.323 compliant proxy servers or
firewalls.
Choosing Proprietary or H.323 mode for your new MultiVOIP200
The MultiVOIP200s are shipped with the H.323 compatible firmware version 2.51 installed. If you want to
run in proprietary mode(compatible with versions prior to 2.50 and 2.51), you will need to download firmware
version 2.01D to your MultiVOIP200. Refer to the users guide for instructions to download version 2.01D.
Both versions are included on the CD shipped with this product.
Warning: If the MultiVOIP has firmware version 2.51 installed and you run “MultiVOIP
configuration” using software version 2.01D, you will receive the message “This version of the software
does not support the MultiVOIP firmware version 2.51. Some of the configuration parameters will be
inconsistent and the Download option is disabled. Please contact MultiTech Tech support for the
latest software release.”. If you receive this message, then you need to download firmware version
2.01D to your MultiVOIP200.
Reasons you may want to use proprietary mode include:
1. If you intend to use your MultiVOIP behind a non-H.323 compliant Proxy server or firewall, you will need
to use version 2.01D.
2. If you are installing your new MultiVOIP in an existing Multi-Tech VOIP network and don’t want to
upgrade all your existing MultiVOIPs to make them H.323 compatible.
==================================================================================
Upgrading your previously-installed MultiVOIP200s from 2.01D or earlier to
H.323 (version 2.51).
MVP200 version 2.51 Installation Instructions
Note: steps 3 - 4 must be performed locally via the command port.
Note:  there are two different MVP200 hardware platforms. If you have the hardware platform where the VOICE
CHANNEL 2 LEDs are above the CHANNEL 1 LEDs, you must confirm that sufficient Flash memory is installed
before proceeding with the upgrade. To verify this, remove the two screws from the bottom of the chassis and slide
the entire cover forward. With the LEDs toward you, verify that the four sockets (U12, U13, U14 and U15) along the
left side of the lowest PCB have a Flash memory chip installed. If sockets U14 and U15 are empty, contact Multi-
Tech to obtain a Flash Memory upgrade (two Flash memory chips, PN 00929046).
1. Run “MultiVOIP configuration” from your old version of MultiVOIP software and take note of the current
settings. Your MultiVOIP will be reset to factory defaults during this upgrade.
2. Uninstall you old version of MultiVOIP software by selecting the “Uninstall MultiVOIP Configuration” option
from the program group.
3. Install the version 2.51 H.323 compatible software from the MultiVOIP CD, including downloading the default
setup.
4. From the new program group for the MultiVOIP software, run “Upgrade Software.” 
						

							2 5. Run “MultiVOIP Configuration” and reconfigure your MultiVOIP using the settings you noted in step 1. The
upgrade is complete.
===================================================================================
MANUALLY upgrading your previously-installed MultiVOIP200s from
2.01D or earlier to H.323 (version 2.51).
MVP200 version 2.51 MANUAL Installation Instructions
Follow this procedure ONLY if you want to MANUALLY upgrade your MultiVOIP.
Note: steps 5 - 8 must be performed locally via the command port.
Note:  there are two different MVP200 hardware platforms. If you have the hardware platform where the VOICE
CHANNEL 2 LEDs are above the CHANNEL 1 LEDs, you must confirm that sufficient Flash memory is installed
before proceeding with the upgrade. To verify this, remove the two screws from the bottom of the chassis and slide
the entire cover forward. With the LEDs toward you, verify that the four sockets (U12, U13, U14 and U15) along
the left side of the lowest PCB have a Flash memory chip installed. If sockets U14 and U15 are empty, contact
Multi-Tech to obtain a Flash Memory upgrade (two Flash memory chips, PN 00929046).
1. Run MultiVOIP configuration from your old version of MultiVOIP software and take note of the current
settings. Your MultiVOIP will be reset to factory defaults during this upgrade.
2. Uninstall your old version of MultiVOIP software by selecting the Uninstall MultiVOIP Configuration option
from the program group.
3. Install the H.323 compatible software from the MultiVOIP CD.
4. From the program group of the MultiVOIP software, run Download H.323 Stack and select the default file.
5. From the program group of the MultiVOIP software, run Download Voice Coders and select the default file.
6. From the program group of the MultiVOIP software, run Download Factory Defaults.
7. From the program group of the MultiVOIP software, run Download Firmware. Under File Name,
enter *.upg and hit enter.
Note: Since there are two different hardware platforms for the MultiVOIP200, you will be asked to select the upgrade
file.
If your MultiVOIP200 VOICE/FAX 2 LEDs are above the VOICE/FAX 1 LEDs, select
the file BOOT_200.UPG. However, if your MultiVOIP Voice/Fax 2 LEDs are to the
right of the Voice/Fax 1 LEDs (i.e., on the front panel of the smaller cabinet), select the
file BOOT_20A.UPG.
Warning: If you select the incorrect file your MultiVOIP will need repair.
8. From the program group of the MultiVOIP software, run Download Firmware and select the file mtvoip.bin.
9. Run MultiVOIP Configuration and reconfigure your MultiVOIP. The upgrade is complete.