MSI Z97 Gaming 5 Manual

English
En-9

CPU (Central Processing Unit)
 Important
Overheating
Overheating can seriously damage the CPU and motherboard. Always make sure the cooling fans work properly to protect the CPU from overheating. Be sure to apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
Replacing the CPU
When replacing the CPU, always turn off the system’s power supply and unplug the power supply’s power cord to ensure the safety of the CPU....

English
En-10

CPU & Heatsink Installation
When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability. Follow the steps below to ensure correct CPU and heatsink installation. Wrong installation can damage both the CPU and the motherboard.
1. Push the load lever down to unclip it and lift to the fully open position .
2.  The load plate will automatically lift up as the load lever is pushed to  the fully open...

English
En-11

3. Align the notches with the socket alignment keys. Lower the CPU str aight down, without tilting or sliding the CPU in the socket. Inspect the CPU to check if it is properly seated in the socket.
4.  Close and slide the load plate under the retention knob. Close and en gage the 
load lever. 
Alignment Key
CPU notches
Retention knob
5. When you press down the load lever the PnP cap will automatically p op up from the CPU socket. Do not discard the PnP cap. Always replace the PnP cap if...

English
En-12

 Important
Confirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.
Whenever the CPU is not installed, always protect the CPU socket pins by covering the socket with the plastic cap.
If you purchased a separate CPU and heatsink/ cooler, Please refer to the documentation in the heatsink/ cooler package for more details about installation.
•
•
• 7. Locate the CPU fan connector on the motherboard.
8.  Place the heatsink on the motherboard with the fan’s...

English
En-13

Memory
These DIMM slots are used for installing memory modules. 
DIMM1DIMM2DIMM3DIMM4
 Video Demonstration
Watch the video to learn how to install memories.
http://youtu.be/76yLtJaKlCQ
Dual-Channel mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive data with two data bus channels simultaneously. Enabling Dual-Channel mode can enhance system performance. The following illustrations explain the population rules for Dual-Channel mode.
DIMM2
DIMM4...

English
En-14

Mounting Screw Holes
When installing the motherboard, first install the necessary mounting stands required for an motherboard on the mounting plate in your computer case. If there is an I/O back plate that came with the computer case, please replace it with the I/O backplate that came with the motherboard package. The I/O backplate should snap easily into the computer case without the need for any screws. Align the mounting plate’s mounting stands with the screw holes on the motherboard...

English
En-15

Power Supply
 Video Demonstration
Watch the video to learn how to install power supply connectors.
http://youtu.be/gkDYyR_83I4
JPWR1~2: ATX Power Connectors
These connectors allow you to connect an ATX power supply. To connect the ATX power supply, align the power supply cable with the connector and firmly press the cable into the connector. If done correctly, the clip on the power cable should be hooked on the motherboard’s power connector.
1 3 . + 3 . 3
V
1 . + 3 . 3
V
1 4 . - 1 2 V
2 ....

English
En-16

Expansion Slots
This motherboard contains numerous slots for expansion cards, such as discrete graphics or audio cards.
PCI_E1~7: PCIe Expansion Slots
The PCIe slot supports the PCIe interface expansion card.
PCIe 2.0 x1 Slot
PCIe 3.0 x16 Slot
 Important
When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software...

English
En-17

Video/ Graphics Cards 
If available, this motherboard takes advantage of the CPU’s integrate graphics processor, but discrete video cards can be installed by way of the motherboard’s expansion slots. Adding on one or more discrete video cards will significantly boost the system’s graphics performance. For best compatibility, MSI graphics cards are recommended.
 Video Demonstration
Watch the video to learn how to install a graphics card on PCIe x16 slot with butterfly lock....

English
En-18

Internal Connectors
SATA1~6: SATA Connectors
This connector is a high-speed SATA interface port. Each connector can connect to one SATA device. SATA devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD/ DVD/ Blu-Ray).
 Video Demonstration
Watch the video to learn how to Install SATA HDD.
http://youtu.be/RZsMpqxythc
SATA2
SATA1
SATA4
SATA3SATA6
SATA5
 Important
The SATA5 and SATA6 ports will be unavailable when installing a module in the M.2 port.
Many SATA...