MSI X99s Gaming 7 Manual

- 71 -
C-1.	UEFI	RAID	Configuration
Only	Windows	8.1/8	64-bit	supports	UEFI	RAID	configuration.
Step 1:
In BIOS Setup, go to BIOS Features and set Windows 8 Features to Windows 8 and CSM Support to Disabled 
(Figure	2).	Save	the	changes	and	exit	BIOS	Setup.
Step 2:
After the system reboot, enter BIOS Setup again. Then enter the Peripherals\Intel(R) Rapid Storage Technology 
sub-menu	(Figure	3).	
Figure 2
Figure 3
Con

- 72 -
Step 3:
On the Intel(R) Rapid Storage Technology menu, press  on Create RAID Volume to enter the Create 
RAID Volume	screen.	 Enter	a	volume	 name	with	1~16	 letters	 (letters	 cannot	be	special	 characters)	 under	the	
Name	item	 and	press	 .	 Then,	select	a	 RAID	 level	(Figure	 4).	RAID	 levels	 supported	 include	RAID	0,	
RAID	1,	RAID	 10,	and	 RAID	 5	(the	 selections	 available	depend	on	the	 number	 of	the	 hard	 drives	 being	installed). 	
Next, use the down arrow key to move to Select...

- 73 -
Step 5:
After setting the capacity, move to Create Volume	and	press		to	begin.	(Figure	6)
After completing, you'll be brought back to the Intel(R) Rapid Storage Technology screen. Under RAID Volumes 
you can see the new RAID volume. To see more detailed information, press  on the volume to check fo\
r 
information	on	RAID	level,	stripe	block	size,	array	name,	and	array	capacity,	etc.	(Figure	7)
Figure 6
Figure 7
Configuring	SATA	Hard	Drive(s)  

- 74 -
Delete RAID Volume
To delete a RAID array, press  on the volume to be deleted on the Intel(R) Rapid Storage Technology 
screen. After entering the RAID VOLUME INFO screen, press  on Delete to enter the Delete screen. 
Press  on Yes	(Figure	8).	
Figure 8
Configuring	SATA	Hard	Drive(s)  

- 75 -
C-2.	Configuring	Legacy	RAID	ROM
Enter the Intel®	legacy 	RAID	 BIOS	 setup	 utility	to	configure	 a	RAID	 array.	 Skip	this	step	 and	proceed	 with	the	
installation	of	Windows	operating	system	for	a	non-RAID	configuration.
Step 1:
After the POST memory test begins and before the operating system boot begins, look fo\
r a message which says 
"Press	 	 to	enter	 Configuration	 Utility"	(Figure	 9).	Press	 	 +		 to	enter	 the	RAID	 Configuration	 Utility.
Figure 9
Step 2:
After you press  +...

- 76 -
Step 3: 
After entering the CREATE VOLUME MENU	screen,	 enter	a	volume	 name	with	1~16	 letters	 (letters	 cannot	be	
special	 characters)	 under	the	Name	item	 and	press	 .	 Then,	select	 a	RAID	 level	(Figure	 11).	RAID	 levels	
supported	 include	RAID	0,	RAID	 1,	RAID	 10,	and	 RAID	 5	(the	 selections	 available	depend	on	the	 number	 of	the	
hard	drives	being	installed).	Press		to	proceed.
Step 4:
Under Disks item, select the hard drives to be included in the RAID array. If only two hard...

- 77 -
Step 5:
Enter the array capacity and press . Finally press  on the Create Volume item to begin creating 
the	RAID	 array.	 When	 prompted	 to	confirm	 whether	 to	create	 this	volume,	 press		to	confirm	 or		 to	
cancel	(Figure	13).
When completed, you can see detailed information about the RAID array in the DISK/VOLUME INFORMATION 
section,	including	the	RAID	level,	stripe	block	size,	array	name,	and	array	capacity,	etc.	(Figure	14)
To exit the RAID BIOS utility, press  or select 6. Exit in MAIN...

- 78 -
Recovery Volume Options
Intel® Rapid Recover Technology provides data protection by allowing users to easily restore data and system 
operation using a designated recovery drive. With the Rapid Recovery Technology, which employs RAID 1 
functionality, users can copy the data from the master drive to the recovery drive; if needed, the data on the 
recovery drive can be restored back to the master drive.
Before you begin: •The recovery drive must have equal or greater capacity than the master d\...

- 79 -
Figure 17
Step 3:
Press  under the Select Disks item. In the SELECT DISKS box, press  on the hard drive you want 
to	use	 for	the	 master	 drive	and	press	 	 on	the	 hard	 drive	 you	want	 to	use	 for	the	 recovery	 drive.	(Make	 sure	
the	recovery	 drive	has	equal	 or	larger	 capacity	 than	the	master	 drive.)	Then	press	 	 to	confirm	 (Figure	17).
Step 4:
Under Sync, select Continuous or On Request	(Figure	 18).	When	 set	to	Continuous, changes made to the 
data on the master drive will be...

- 80 -
Delete RAID Volume
To delete a RAID array, select Delete RAID Volume in MAIN MENU and press . In the DELETE 
VOLUME MENU section, use the up or down arrow key to select the array to be deleted and press . 
When	prompted	to	confirm	your	selection	(Figure	19),	press		to	confirm	or		to	abort.
Figure 19
Acceleration Options
This	option	 allows	 you	to	view	 the	status	 of	your	 accelerated	 drive/volume	 (Figure	20)	created	 using	the	Intel®  
IRST utility. In case you are unable to run the Intel®...