MSI X58 Proe Manual

Hardware Setup▍MS-7522

2-25
Hardware Setup▍MS-7522

Led StatuS indicatorS
RE S E TClrCMOS
D I M Mwa r n i n gL ED
P C I EL ED
Po w er LE D
S u s p e nd LE D
C PU Pha s eL E D s
P C I EL ED
P C I EL ED
P C I EL ED
P C I EL ED
P CI LE D
P CI LE D
CPU Phase LEDs
These LEDs ndcate the current CPU power phase mode. Follow the nstructons
below to read.
 5 of the LEDs wll lght blue when CPU s n 5 phase power mode.
 4 of the LEDs wll lght blue when CPU s...

2-26
Hardware Setup▍MS-7522
DIMM Warnng LED
Lghts red when the ncorrect memory nstalled nto DIMM_C0/ DIMM_C1 (the DIMMs
of 3rd channel).
Power LED
Lghts green when the system s n power-on(S0/S1) status.
Suspend LED
Lghts yellow when the system s suspended (S3/S4/S5).
PCIE and PCI LEDs
Lghts blue when the slots s functonal. 

2-3-1
Ths  chapter  provdes 
nformaton  on  the  BIOS  Setup 
program and allows you to configure  the system for op-
tmum use.
You may need to run the Setup program when:
An error message appears on the screen durng 
the  system  bootng  up,  and  requests  you  to  run 
SETUP.
You want to change the default settngs for cus
-
tomzed features.
■
■
Chapter 3
BIOS Setup 

3-2
BIOS Setup▍MS-7522
BIOS Setup▍MS-7522

entering Setup
Power on the computer and the system wll start POST (Power On Self Test) process. When the message below appears on the screen, press  key to enter Setup.
Press DEL to enter SETUP
If the message dsappears before you respond and you stll wsh to enter Setup, restart 
the system by turnng t OFF and On or pressng the RESET button. You may also re-
start the system by smultaneously pressng , , and  keys....

BIOS Setup▍MS-7522

3-3
BIOS Setup▍MS-7522

Control Keys
Move to the prevous tem
Move to the next tem
Move to the tem n the left hand
Move to the tem n the rght hand
Select the tem
Jumps to the Ext menu or returns to the man menu from a submenu
Increase the numerc value or make changes
Decrease the numerc value or make changes
General Help
Enter CPU Specficatons submenu
Enter Memory-Z submenu
Load Optmzed Defaults
Load...

3-4
BIOS Setup▍MS-7522
BIOS Setup▍MS-7522

the Main Menu
Standard CMOS Features
Use ths menu for basc system configuratons, such as tme, date etc.
Advanced BIOS Features
Use ths menu to setup the tems of AMI?specal enhanced features.
Integrated Perpherals
Use ths menu to specfy your settngs for ntegrated perpherals.
Power Management Setup
Use ths menu to specfy your settngs for power management.
H/W Montor
Ths...

BIOS Setup▍MS-7522

3-5
BIOS Setup▍MS-7522

User Settngs
Use ths menu to save/ load your settngs to/ from CMOS for BIOS.
M-Flash
Use ths menu to read/ flash the BIOS from storage drve (FAT/ FAT32 format only).
Load Fal-Safe Defaults
Use  ths  menu  to  load  the  default  values  set  by  the  BIOS  vendor  for  stable  system 
performance.
Load Optmzed Defaults
Use ths menu to load the default values set by the manboard manufacturer...

3-6
BIOS Setup▍MS-7522
BIOS Setup▍MS-7522

Standard cMoS featureS
The tems  n Standard CMOS Features Menu  ncludes some basc setup tems. Use the 
arrow keys to hghlght the  tem and then use the  or  keys to select the 
value you want n each tem.
Date (MM:DD:YY)
Ths allows you to set the system to the date that you want (usually the current date). 
The format s   . day    Day  of  the  week,  from  Sun  to  Sat,  determned  by  BIOS....

BIOS Setup▍MS-7522

3-7
BIOS Setup▍MS-7522

Devce / Vendor / Sze
It wll showng the devce nformaton that you connected to the SATA connector.
LBA/Large Mode
Ths  allows  you  to  enable  or  dsable  the  LBA  Mode.  Settng  to  Auto  enables  LBA 
mode  f  the  devce  supports  t  and  the  devces s  not  already  formatted  wth  LBA 
mode dsabled. 
DMA Mode
Select DMA Mode. 
Hard Dsk S.M.A.R.T.
Ths  allows...

3-8
BIOS Setup▍MS-7522
BIOS Setup▍MS-7522

advanced bioS featureS
Full Screen Logo Dsplay
Ths  tem  enables  ths  system  to  show  the  company  logo  on  the  boot-up  screen.  Set
-
tngs are:
[Enabled]  Shows a stll mage (logo) on the full screen at boot.
[Dsabled]  Shows the POST messages at boot.
Quck Bootng
Settng  the  tem  to  [Enabled]  allows  the  system  to  boot  wthn  10  seconds  snce  t  wll 
skp...