MSI Router RG54G3 User Manual

							 
66  WPA:   
 
For this function, we need the server to authenticate. This function is like 802.1x. 
 
The above is our environment: 
 
Method 1: 
1. The UserA or UserB have to get certificate from Radius, first. 
http://192.168.122.1/certsrv  
account : fae1 
passwd : fae1   
 
2. Then, Install this certificate and finish. 
3. Go to the Web manager of Wireless Router to configure, like below: 
  
						

							 
67    
 
4. Go to Odyssey Client Manager, choose  “Profiles ” and Setup Profile name as  “1 ” 
   
 
Login name and passwd are fae1 and fae1. 
Remember that you get certificate from Radius in Step1. 
  
						

							 
68  5. Then Choose 
“certificate ” like above.    
						

							 
69   
6. Then go to Authentication and first Remove EAP/ TLS and Add EAP/TLS again. 
    
  
						

							 
70   
7. Go 
“Network ” and Select  “1 ” and ok 
     
						

							 
71   
8. Back to Connection and Select 
“1kk. 
If  successfully , the wireless client has to authenticate with Radius Server, like below:  
   
 
9.Result:   
 
 
Method 2: 
1. The UserA or UserB have to get certificate from Radius,first. 
http://192.168.122.1/certsrv  
account:fae1 
passwd:fae1  
						

							 
72    
 
2. Then Install this certificate and finish. 
3. Setting on the router and client: 
 Router: 
 
    
						

							 
73  Client: 
Go to 
“Network Connection ” and select wireless adapter. 
Choose  “View available Wireless Networks ” like below: 
Advanced à choose  “1kk ” 
Select  “WirelessCA and Enable ” in Trusted root certificate authority:   
     
  
  Then, if the wireless client wants to associate, it has to request to authenticate.     
						

							 
74  A
A
A p
p
p p
p
p e
e
e n
n
n d
d
d i
i
i x
x
x  
 
  D
D
D  
 
   
 
  F
F
F A
A
A Q
Q
Q  
 
  a
a
a n
n
n d
d
d  
 
  T
T
T r
r
r o
o
o u
u
u b
b
b l
l
l e
e
e s
s
s h
h
h o
o
o o
o
o t
t
t i
i
i n
n
n g
g
g  
 
 
 
Reset to factory Default  
 
There are 2 methods to reset to default. 
 
1.  Restore with RESET button 
First, turn off the router and press the RESET button in. And then, power on the router and push the RESET button down until the 
M1 and or M2 LED (or Status LED) start flashing, then remove the finger. If LED flashes about 8 times, the RESTORE process 
is completed. However, if LED flashes 2 times, repeat.  
 
2.  Restore directly when the router power on  
First, push the RESET button about 5 seconds (M1 will start flashing about 5 times), remove the finger 
. The RESTORE process is completed.  
 
             
             
    
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							 
75  A
A
A p
p
p p
p
p e
e
e n
n
n d
d
d i
i
i x
x
x  
 
  E
E
E  
 
   
 
  P
P
P r
r
r o
o
o d
d
d u
u
u c
c
c t
t
t  
 
  S
S
S p
p
p e
e
e c
c
c i
i
i f
f
f i
i
i c
c
c a
a
a t
t
t i
i
i o
o
o n
n
n  
 
 
  Hardware and Port Characteristic 
CPU 
AMRISC 10100 Memory 
Flash 1MB, DRAM 2MB LAN Port 
4 x RJ45, 10/100 Mbps with Auto-MDI/MDIX WAN Port 
1 x RJ45, 10/100 Mbps with Auto-MDI/MDIX Input Power 
AC 12V1A Operational & Functional Characteristic 
Firmware Platform 
MSI Proprietary Kernel Management Method 
Web-based  Static IP Address 
Dynamic IP Address (DHCP Client) 
PPP over Ethernet 
Multi-session PPP over Ethernet 
(For Japan only)  PPTP Supported WAN Type 
L2TP  Connect on Demand / Auto-Disconnect 
Manually Connect/Disconnect Connection Scheme 
Auto Reconnect  One-to-Many NAT 
One-to-One NAT 
Virtual Server 
Special Application NAT Functionality 
DMZ Host  MAC-level Access Control 
Inbound/Outbound IP Filter Access Control 
Domain Access Control  NAT Firewall with SPI mode 
Firewall 
DoS Detection  On-web logging Event Logging 
Syslog supported