MSI K9mmv Manual

 
5 CPU Cooler Installation 
When you are installing the CPU, make sure the CPU has a cooler attached on the top to prevent 
overheating. If you do not have the cooler, contact your dealer to purchase and install them 
before turning on the computer. Meanwhile, do not forget to apply some silicon heat transfer 
compound on CPU before installing the cooler for better heat dispersion.  
Follow the steps below to install the CPU & cooler correctly. Wrong installation will cause the 
damage of your CPU &...

 
6 Installing DDRII Modules 
1. The memory module has only one notch on the center and will only fit in the right orientation.  2. Insert the memory module vertically into the DIMM slot. Then push it in until the golden finger 
on the memory module is deeply inserted in the DIMM slot. 
3. The plastic clip at each side of the DIMM slot will automatically close. 
 Power Supply 
The mainboard supports ATX power supply for the power system. Before inserting the power 
supply connector, always make sure that...

 
7   MSI Reminds You...  If you install two hard disks on one cable, you must configure the second drive to Slave mode by setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions.  Serial ATA Connector: SATA1/SATA2 
The mainboard provides 2 high-speed Serial ATA interface ports. The ports support 1ST
 
generation Serial ATA data rates of 150MB /s and are fully compliant with Serial ATA 1.0 
specifications. Each Serial ATA connector can...

 
8 Front Panel Audio Connector: JAUDIO1 
The front panel audio connector allows you to 
connect to the front panel audio and is compliant 
with Intel®
 Front Panel I/O Connectivity Design 
Guide.  
 
 MSI Reminds You...  If you do not want to connect to the front audio header, pins 5 & 6, 9 & 10 have to be jumpered in order to have signal output directed to the rear audio ports. Otherwise, the Line-Out connector on the back panel will not function.     Front USB Connector: JUSB1/JUSB2 
The mainboard...

 
9 PCI (Peripheral Component Interconnect) Slots 
The PCI slots allow you to insert the expansion cards to meet your needs. When adding or 
removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read 
the documentation for the expansion card to make 
any necessary hardware or software settings for the 
expansion card, such as jumpers, switches or BIOS 
configuration. 
 PCI Interrupt Request Routing 
The IRQ, abbreviation of interrupt request line and pronounced I-R-Q, are...

 
10 BIOS Setup 
Power on the computer and the system will start POST (Power On Self Test) process. When the 
message below appears on the screen, press  key to enter Setup. 
DEL: Setup  F11: Boot Menu  TAB: Logo 
If the message disappears before you respond and you still wish to enter Setup, restart the 
system by turning it OFF and On or pressing the RESET button. You may also restart the system 
by simultaneously pressing , , and  keys. 
 Main Page 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Standard CMOS...

 
11  BIOS Setting Password 
Use this menu to set BIOS setting Password. 
 
Save & Exit Setup 
Save changes to CMOS and exit setup. 
 
Exit Without Saving 
Abandon all changes and exit setup. 
 
 
 H/W Monitor 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Chassis Intrusion 
The field enables or disables the feature of recording the chassis intrusion status and issuing a 
warning message if the chassis is once opened. To clear the warning message, set the field to 
[Reset]. The setting of the field will automatically...

 
12 Cell Menu 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Memory Voltage (V) 
Adjusting the memory voltage can increase the memory speed. Any changes made to this 
setting may cause a stability issue, so changing the memory voltage for long-term purpose is 
NOT recommended. 
 
Cool ’n’ Quiet control 
This feature is especially desiged for AMD Athlon processor, which provides a CPU temperature 
detecting function to prevent your CPU’s from overheading due to the heavy working loading. 
 
Auto Disable PCI Clock...

13 Introduction 
Félicitations, vous venez d’acquérir une carte mère Micro-ATX des séries K9MM-V (MS-7312 
v1.x). Les séries K9MM-V sont basées sur les chipsets VIA®
 K8M800 & VIA®
 VT8237R Plus 
offrant un système performant. Destinées aux processeurs avancés AMD®
 Athlon 64/ Athlon X2 
pour le Socket AM2, les séries K9MM-V offrent une solution adaptée tant aux professionnels 
qu’aux particuliers. 
 Schéma: 
 
 
 AGP1BATT+IDE 1
SATA2
SATA1
FDD 1
JWR2
DIMM1
DIMM2BIOS
JCOM1
CPUFAN1
SFAN1
PCI3...

14 Spécificités: 
CPU: 
· Supporte les processeurs AMD®
 Athlon 64/ Athlon X2 (Socket AM2). 
(Pour plus d’informations sur le CPU, veuillez visiter 
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php) 
 
FSB Supporté: 
· Hyper Transport supporte une vitesse jusqu’à 800 MHz (1600 MT/s). 
 
Chipset: 
· North Bridge: chipset VIA®
 K8M800. 
· South Bridge: chipset VIA®
 VT8237R Plus. 
 
Mémoire : 
· DDRII 400/ 533/ 667/ 800 SDRAM (2 GB Max).  
· 2 slots DDRII DIMM (240-pin/ sans...