MSI K7n2 Delta 2 Manual

3-22
MS-6570E ATX Mainboard
H/W Monitor
This section shows the status of your CPU, fan, overall system status, etc.
Monitor function is available only if there is hardware monitoring mechanism onboard.
Chassis Intrusion Detect
The field enables or disables the feature of recording the chassis intrusion status
and issuing a warning message if the chassis is once opened. To clear the warning
message, set the field to [Reset]. The setting of the field will automatically return to
[Enabled] later. Setting...

3-23 BIOS Setup
PC Health Status
Press  and the following sub-menu appears.
Current System/CPU Temperature, NB/CPU Fan Speed, Vcore, +3.3V,
+12.0V, +5.0V, Battery, +5VSB
These items display the current status of all of the monitored hardware de-
vices/components such as CPU voltage, temperatures and all fans’ speeds. 

3-24
MS-6570E ATX Mainboard
Cell Menu
The items in Cell Menu includes some important settings of CPU, AGP, DRAM
and overclocking functions.
Current CPU Clock
It shows the current CPU clock frequency. (Read-only)
Current DRAM Clock
It shows the clock frequency of the installed DRAMs. (read only)
High Performance Mode
This field allows users to control the status of system performance.  Users may
select [Optimized] for the most stable settings by SPD.  [High Performance/Turbo]
will increase the system...

3-25 BIOS Setup
the CPU is temporarily suspending or staying in the low load balance, it will restore
the default settings instead. Usually the Dynamic Overclocking Technology will be
powered only when users PC need to run huge amount of data like 3D games or the
video process, and the CPU frequency need to be boosted up to enhance the overall
performance. Setting options:
[Disabled]Disable Dynamic Overclocking.
[Private]1st level of overclocking, increasing the CPU frequency by
1%.
[Sergeant] 2nd level...

3-26
MS-6570E ATX Mainboard
Adjust CPU Ratio
This setting controls the multiplier that is used to determine the internal clock speed of
the processor relative to the external or motherboard clock speed.
CPU Interface
This setting allows you to select the CPU/FSB parameters. Setting: [Optimal],
[Aggressive]. When [Aggressive] is selected, the system will use overclocked CPU/
FSB parameters. Select [Optimal] for the most stable CPU/FSB parameters.
Adjust DRAM Freq (FSB:DRAM)
This setting controls the ratio...

3-27 BIOS Setup
AGP Clock Control
This item allows users to set the AGP clock manually or by default.  Options: [Default],
[Manual].
AGP Clock Value
When AGP Clock Control is set to [Manual], users can key in a DEC number between
[66] and [120].
FSB Spread Spectrum
This item is used to enable or disable the FSB clock generator’s Spread Specturm
feature.  When overclocking the FSB, always set it to [Disabled].   Options: [Disabled],
[0.50%], [1.00%].
AGP Spread Spectrum
This item is used to enable or...

3-28
MS-6570E ATX Mainboard
Load Fail-Safe/Optimized Defaults
The two options on the main menu allow users to restore all of the BIOS settings to
the Fail-Safe or Optimized Defaults. The Optimized Defaults are the default values set
by the mainboard manufacturer specifically for optimal performance of the mainboard.
The Fail-Safe Defaults are the default values set by the BIOS vendor for stable
system performance.
When you select Load Fail-Safe Defaults, a message as below appears:
Pressing Y loads the...

3-29 BIOS Setup
Set Supervisor/User Password
When you select this function, a message as below will appear on the screen:
Type the password, up to six characters in length, and press . The
password typed now will replace any previously set password from CMOS memory.
You will be prompted to confirm the password.  Retype the password and press
. You may also press  to abort the selection and not enter a password.
To clear a set password, just press  when you are prompted to enter
the password. A message...

Introduction to DigiCell
4-1
Chapter 4. Introduction to DigiCell
Introduction to DigiCell
Chapter 2. Hardware Setup
short-cut icon in the system tray
short-cut path in the start-up menu
(path: Start-->Programs-->MSI-->DigiCell)
DigiCell, the most useful and powerful utility that MSI has spent much
research and efforts to develop, helps users to monitor and configure all the
integrated peripherals of the system, such as audio program, power
management, MP3 files management and communication / 802.11g...

MSI FeatureMS-6570E ATX Mainboard
4-2
Before using this utility, it is required to have all the integrated peripherals/cards (LAN
card, Wireless LAN card, MegaStick... etc.) and all the necessary drivers (onboard
LAN driver, audio driver, CoreCenter, Live Update... etc.) installed correctly.
The icon representing each item will be lit up if it is inserted/installed correctly and
properly. Otherwise, the icon will remain gray and user is not able to view the
functionality/connection of that item.
Main...