MSI 865pe Neo2 V Manual

							2-20
MS-6728 ATX Mainboard
BATT
+
Serial ATA /Serial ATA RAID Connectors controlled by Promise
20378: IDE3, SATA3 & SATA4 (Optional)
The brand new Promise 20378 chipset supports  one IDE connector IDE3
and two serial connectors SATA1& SATA2.
IDE3 is a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133 controller
that provides PIO mode 0~6, Bus Master, and Ultra DMA 66/100/133 function.
You can connect up to 2 hard disk drives---one IDE master and one IDE slave.
And STAT3 & SATA4 are dual high-speed Serial ATA interface ports.
Each supports 1
st generation serial ATA data rates of 150 MB/s. Both connectors
are fully compliant with Serial ATA 1.0 specifications. Each Serial ATA connector
can connect to 1 hard disk device. Please refer to Serial ATA/Serial ATA Raid
manual for detail software installation procedure.
SATA3
IDE3
7
1
SATA4 
						

							2-21
Hardware Setup
MSI Reminds You...
Please do not fold the serial ATA cable in a 90-degree angle,
which will cause the loss of data during the transmission.
PIN SIGNAL PIN SIGNAL
1 GND 2 TXP
3 TXN 4 GND
5 RXN 6 RXP
7 GND
SATA1~  SATA4 Pin Definition
Connect to serial ATA ports
Take out the dust cover and
connect to the hard disk
devicesOptional Serial ATA cable 
						

							2-22
MS-6728 ATX Mainboard
BATT
+
CD-In Connector: JCD1
The connector is for CD-ROM audio connector.
S-Bracket (SPDIF) Connector: JSP1 (Optional)
The connector allows you to connect a S-Bracket for Sony & Philips
Digital Interface (SPDIF).  The S-Bracket offers 2 SPDIF jacks for digital
audio transmission (one for optical fiber connection and the other for coaxial),
and 2 analog Line-Out jacks for 4-channel audio output.
To attach the fiber-optic cable to optical SPDIF jack, you need to remove
the plug from the jack first.  The two SPDIF jacks support SPDIF output only.
For more information on the S-Bracket, refer to Appendix: Using 4- or 6-Channel
Audio Function.
JCD1
GNDLR
JSP1
     1  11
    2   12 
						

							2-23
Hardware Setup
PIN SIGNAL DESCRIPTION PIN SIGNAL DESCRIPTION
1 VCC5 VCC 5V 2 VDD3 VDD 3.3V
3 SPDFO S/PDIF output 4 (No Pin) Key
5 GND Ground 6SPDFI S/PDIF input
7 LFE-OUT Audio bass output 8 SOUT-R Audio right surrounding output
9 CET-OUT Audio center output 10 SOUT-L Audio left surrounding output
11 GND Ground 12 GND Ground
JSP1 Pin Definition
Optional S-Bracket
SPDIF jack (optical)
SPDIF jack (coaxial)Analog Line-Out jack
Connect to JSP1
MSI Reminds You...
Before connecting to the S-Bracket, be sure to remove the JS1
jumpers (see p.2-32 for details) and power off the system first, then
you are able to attach your S-Bracket to the JSP1 connector. Your
mainboard may be damaged seriously if not following the
instruction above. 
						

							2-24
MS-6728 ATX Mainboard
BATT
+
IEEE 1394 Connectors: J1394_1, J1394_2, J1394_3 (Optional)
The mainboard provides three 1394 pin headers that allow you to con-
nect optional IEEE 1394 ports.
J1394_1, J1394_2, J1394_3
(from left to right)
J1394 Pin Definition
PIN   SIGNAL              PIN SIGNAL
1   TPA+                2 TPA-
3   Ground                4 Ground
5   TPB+                6 TPB-
7  Cable power              8 Cable power
9   Key (no pin)             10 Ground
   9
    2
  10   1 
						

							2-25
Hardware Setup
How to attach the IEEE 1394 Port:
Foolproof
design
Connected separately  to J1394_1,
J1394_2 and J1394_3.
1394 Port 
						

							2-26
MS-6728 ATX Mainboard
BATT
+
Front Panel Connectors: JFP1 & JFP2
The mainboard provides two front panel connectors for electrical con-
nection to the front panel switches and LEDs. JFP1 is compliant with Intel®
Front Panel I/O Connectivity Design Guide.
PIN SIGNAL DESCRIPTION
1 HD_LED_P Hard disk LED pull-up
2 FP PWR/SLP MSG LED pull-up
3 HD_LED_N Hard disk active LED
4 FP PWR/SLP MSG LED pull-up
5 RST_SW_N Reset Switch low reference pull-down to GND
6 PWR_SW_P Power Switch high reference pull-up
7 RST_SW_P Reset Switch high reference pull-up
8 PWR_SW_N Power Switch low reference pull-down to GND
9 RSVD_DNUReserved. Do not use.
 JFP1 Pin Definition
PIN SIGNAL PIN SIGNAL
1 GND 2 SPK-
3 SLED 4 BUZ+
5 PLED 6 BUZ-
7 NC 8 SPK+
JFP2 Pin Definition
JFP2JFP1
1 9
10HDD
LED Reset
Switch
Power
LED Power
Switch2
SpeakerPower
LED
7
8
21 
						

							2-27
Hardware Setup
BATT
+
Front Panel Audio Connector: JAUD1
The JAUD1 front panel audio connector allows you to connect to the
front panel audio and is compliant with Intel® Front Panel I/O Connectivity
Design Guide.
PIN SIGNAL DESCRIPTION
1 AUD_MIC Front panel microphone input signal
2 AUD_GND Ground used by analog audio circuits
3 AUD_MIC_BIASMicrophone power
4 AUD_VCCFiltered +5V used by analog audio circuits
5 AUD_FPOUT_R Right channel audio signal to front panel
6 AUD_RET_R Right channel audio signal return from front panel
7 HP_ON Reserved for future use to control headphone amplifier
8 KEY No pin
9 AUD_FPOUT_L Left channel audio signal to front panel
10 AUD_RET_L Left channel audio signal return from front panel
JAUD1 Pin Definition
MSI Reminds You...
If you don’t want to connect to the front audio
header, pins 5 & 6, 9 & 10 have to be jumpered in
order to have signal output directed to the rear
audio ports. Otherwise, the Line-Out connector on
the back panel will not function.
JAUD1
1
2 9
10
5
6 10      9 
						

							2-28
MS-6728 ATX Mainboard
BATT
+
Front USB Connectors: JUSB1 & JUSB2 (Optional)
The mainboard provides two USB 2.0 pin headers JUSB1 & JUSB2
(Optional) that are compliant with Intel® I/O Connectivity Design Guide. USB
2.0 technology increases data transfer rate up to a maximum throughput of
480Mbps, which is 40 times faster than USB 1.1, and is ideal for connecting
high-speed USB interface peripherals such as USB HDD, digital cameras,
MP3 players, printers, modems and the like.
PIN SIGNAL PIN SIGNAL
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 GND 8 GND
9 Key (no pin) 10 USBOC
JUSB1 & JUSB2 Pin Definition
JUSB2, JUSB1(USB 2.0/Intel spec)      1     2
  10
   9 
						

							2-29
Hardware Setup
BATT
+
D-Bracket™ 2 Connector: JDB1 (Optional)
The mainboard comes with a JDB1 connector for you to connect to D-
Bracket™ 2. D-Bracket™ 2 is a USB Bracket that supports both USB1.1 & 2.
0 spec. It integrates four LEDs and allows users to identify system problem
through 16 various combinations of LED signals. For definitions of 16 signal
combinations, please refer to D-Bracket™  2 at P.1-10 in Chapter 1.
Pin Signal
1         DBG1 (high for green color)
2         DBR1 (high for red color)
3         DBG2 (high for green color)
4         DBR2 (high for red color)
5         DBG3 (high for green color)
6         DBR3 (high for red color)
7         DBG4 (high for green color)
8         DBR4 (high for red color)
9         Key (no pin)
10       NC
JDB1 Pin Definition
JDB1
Connected to JUSB1 Connected to JDB1LEDs
     1    9
    2
  10