Mountfield Lawn Mower SP550 Combi Owners Manual
Have a look at the manual Mountfield Lawn Mower SP550 Combi Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 153 Mountfield manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11 ENGLISHGB SPARK PLUG Never remove the spark plug or spark plug cable when checking to see if there is a spark. Always use an approved test instrument. Clean the spark plug regularly (every 50 hours of run time or once a season). Use a wire brush for cleaning. Change the spark plug if the electrodes are exces- sively burnt or if the plug is damaged. The engine manufacturers recommendations are as follows: (fig. 15): Champion J19LM (RJ19LM), spark gap 0.75 mm. ADJUSTING CLUTCH CABLE If the drive does not engage when the power drive lever is pressed against the handle, or if the lawn- mower feels cumbersome or slow, this may be be- cause the clutch in the transmission is slipping. To rectify this situation, adjust the clutch cable as fol- lows: 1. When the clutch loop is released, it should be possible to push the mower without any resist- ance. If this is not the case, screw in the nipple T until the mower can be pushed (fig. 17). 2. When the clutch loop is pressed in approx. 2 cm (posi- tion 1), there should be some resistance when pushing the lawnmower. With the clutch loop fully pressed in (position 2) it should not be possible to push the mower. Unscrew the nipple T until this position is achieved. CHANGING BLADES Wear protective gloves when changing blade(s) to avoid cutting yourself. Check the blade system regularly. Check particularly the curved area behind the blade edge for traces of wear. If the blade shows traces of damage it should be re- placed. A worn blade creates imbalance and can damage the mower. Always check the blades after a collision. First dis- connect the spark plug cable. If the blade system has been damaged, defective parts should be re- placed. Always use genuine spare parts. Replace-ment blade pack reference MS1186 is available from all B&Q stores and specialist garden machin- ery dealers. To replace the blade, slacken the screw (fig. 18). Fit the new blade so that the stamped logo is turned up facing the blade holder (not facing the grass). Reinstall the washer and screw. Tighten the screw properly. Tightening torque 40 Nm. When replacing the blade, the blade screw should also be replaced. The guarantee does not cover damage to the blade, blade holder or engine caused by running into ob- stacles. When replacing the blade, the blade holder and blade screw, always use genuine spare parts. Non- genuine spare parts can entail a risk of injury or damage, even if they fit the machine. SHARPENING THE BLADES Sharpening of the blades must be done by wet method grinding, using a whetstone or a grind- stone. It is important to keep the same angle as the original edge. For safety reasons, the blades should not be sharp- ened on an emery wheel. A very high temperature could cause the blades to become brittle. Once the blade has been sharpened, it must then be balanced to avoid vibra- tion damage. Refer tp your local dealer. STORAGE WINTER STORAGE Empty the fuel tank. Start the engine and let it run until it stops. The same petrol must not re- main in the tank for more than one month. Tip up the mower and unscrew the spark plug. Pour a tablespoon of engine oil into the spark plug hole. Pull out the starter handle slowly so that the oil is distributed in the cylinder. Screw in the spark plug. Thoroughly clean the mower and store it indoors in a dry place.
12 ENGLISHGB SERVICE ACCESSORIES/SPARE PARTS Always use genuine spare parts and ac- cessories. Non-genuine spare parts and accessories have not been checked and approved by the lawnmower manufac- turer. Use of non-genuine spare parts and accessories can lead to the risk of in- jury, even if they fit the machine. The lawnmower manufacturer does not ac- cept any liability for injuries caused by the use of such parts or accessories. Genuine spare parts are stocked by authorised service centres and by many dealers. We recommend that you take the machine to an au- thorised service station for annual servicing, main- tenance and inspection of safety equipment. For service and spare parts, please contact the deal- er where the machine was purchased. PRODUCT IDENTITY The identity of the product is determined by two components: 1. Article and serial number of the machine: Appears on this label fixed to the chassis of the machine. 2. Model, type and serial number of the engine: Appears on the engine fan housing as shown: Use this identification whenever you contact a service workshop or buy replacement parts.As soon as possible after buying the machine, write the above numbers on the back page of this booklet. The manufacturer reserves the right to make changes to the product without prior notice. PURCHASE TERMS A full guarantee is issued against manufacturing and material defects. The user must carefully fol- low the instructions given in the enclosed docu- mentation. Guarantee period For consumer use: Cutter deck is guaranteed for 10 years. All other, non-consumable, items are guar- anteed for two years against defective components and poor workmanship. For professional use: three months from the pur- chase date. Exceptions The guarantee does not cover damage due to: - neglect of the user to acquaint himself with ac- companying documentation - carelessness - incorrect and non-permitted use or assembly - the use of non-genuine spare parts - the use of accessories not supplied or approved by the manufacturer Neither does the guarantee cover: - wearing components such as blades, belts, wheels and cables - normal wear - engines. These are covered by the appropriate manufacturer’s guarantees with separate terms and conditions. The purchaser is covered by each country’s nation- al laws. The rights to which the purchaser is enti- tled with the support of these laws are not restricted by this guarantee. TYP ART. NR. SERIE NR. XX-XXXX-XX XXXXXXXX TM:HYKVÄKSYMA maahantuoja STIGA OY LWATÜV Rheinland geprü fte Sicherheit SNDFI22 Kg 1,6 kW 230 V 50 Hz 2850 min Nätsäkring 10 AR S461 86ART. NR SERIE NR Briggs & Stratton
STOP EC conformity declaration 1.Category 5.VibrationLawnmower with petrol engine E531 12-9686 8,0 m/s 2 (ISO 5349) 2.Type 3.Item no STIGA Produktion AB P.O. Box 1006 SE-573 28 Tranås Sweden8.Make Mountfield 9.Cutting width53 cm10.Serial numberSee label on chassis 6A.Guaranteed sound power level (L WA)99 dB(A)11. Engine MakeBriggs & Stratton XTE 60 Model 12.Rotation speed3000 rpm 6B.Measured sound power level97 dB(A) 7.Notified body ITS Testing & Certification Ltd Notified Body repre- sentative 0359 4.Manufacturer This product conforms to - Electromagnetic Compatibility Directive 89/336/EEC - Machinery Directive 98/37/EEC with special reference to appendix 1 of the directive regarding essential health and safety requirements in conjunction with manufacturing - Noise Emission Directive 2000/14/EC Managing Director Mats Antonsson Issued in Tranås 2002-01-21
................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ................................................................................................................................................................................................................................................................................................... ...................................................................................................................................................................................................................................................................................................