Motorola Sliver 2 Owners Manual

MOTOROLA
SLIVER II
EN 

ENCheck it out1
Check it outhere’s what you can do
Enjoy crystal clear calls and rich sound with your 
MOTOROLA SLIVER II Bluetooth® headset. So 
small, it’s barely noticeable. So packed with 
features, like wide-band audio and noise 
cancellation, it’s impossible to ignore.
Go ahead, check it out:
At a glance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2
Charge it  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   3
Connect & go. . . . ....

2At a glance EN
At a glancethe important bits, quick and easy
Status 
Light
Volume 
Buttons
Call 
ButtonChar ge 
(Micro  USB)
Turn On & Off
Turn the
earpiece
left or right
to turn on.
Return earpiece to closed
(storage) position to turn off.
Char ge & Store We
ar 

ENCharge it3
Charge itlet’s get you up and running
Headset Status Light Green - more than 4 hours talk-time
 Yellow  -  between 2-3 hours talk-time
 Red  -  less than 1 hour talk-timeCharge 
Headset
Case Status Light Green  -  fully charged (two full headset charges)
 Yellow  -  30-70% charged (one full headset charge)
 Red  -  less than 30% charged
      (less than one headset charge)Char ge 
Case
Note: You  can 
close the case lid 
when charging.
Charge
(Micro USB) 

4Charge it EN
You can charge the headset in several ways:
•Place the headset in the case, and plug the 
charger into the case’s micro USB port. The 
headset charges first, then the case.
 Charge the case first, then place the headset 
in the case when you need to charge it.
 Plug the charger directly into the headset’s 
micro USB port.
Notes:  
 Fully charge the headset before you use it.
 The case or headset status light flashes when 
it is charging. When  not charging, the case or 
headset status light...

ENCharge it5
recycling facility. Any attempt to remove or 
replace your battery will damage the device, void 
your warranty, and could cause injury.
Tip: To save battery power, turn off the headset 
when you’re not using it. 

6Connect & go EN
Connect & golet’s get you connected
2Turn on your headset and follow the
voice prompts.
4When the device and headset connect,
you’ll hear “pair ing complete”.
3Go to the Bluetooth menu on your device
to pair & connect with the headset. Enter 
passcode 0000 if prompted.
1Turn on Bluetooth on your device. 

ENBasics7
Basicsstandard features, advanced quality
Calls
To …
answer a call Press the Call button.
reject a call Press and hold the Volume Up 
or Volume Down button until 
you hear a tone.
make a voice 
dial call Press the Call button to 
activate voice recognition.
mute or 
unmute a 
call Press and hold the Volume Up 
and Volume Down buttons 
until you hear “
mute on” or 
“ mute off ”.
end a call Press the Call button. 

8Basics EN
Notes:  
 Some features are phone/network dependent.
 Using a mobile device or accessory while 
driving may cause distraction and may be 
illegal. Always obey the laws and drive safely.
change call 
volume
Press the Volume Up or 
Volume Down button. To 
quickly change volume, press 
and hold the Volume Up or 
Volume Down button.
answer a 
second 
incoming 
call Press the Call button.
reject a 
second call Press and hold the Volume Up 
or Volume Down button until 
you hear a tone.
To … 

ENBasics9
Headset status light
Light shows… your headset is…
two blue blinks, 
pause, repeat powered on & 
searching for a device
steady blue for three 
seconds, then off connected to a device
flashing red charging, battery at  low power
flashing yellow charging, battery at  medium power
flashing green charging, battery at  high power
steady green connected to charger,  battery fully charged